Skip site navigation (1)Skip section navigation (2)
Date:      Wed, 21 Mar 2001 16:59:40 -0500 (EST)
From:      Mobile Computer <mobile@vta.com>
To:        freebsd-mobile@FreeBSD.ORG
Subject:   2 Socket Serial Cards on 1 4.2 RELEASE Laptop?
Message-ID:  <200103212159.QAA57943@mailhub.vta.com>

next in thread | raw e-mail | index | archive | help
Hello All,

I am looking for advice on how to approach making  2 (identical) single-port 
16550A Serial PCMCIA cards possible on the same 4.2 RELEASE Laptop. 
I am unclear if this is an unsupported operation for this specific card 
type, please advise, likewise if something obvious appears to be missing here. 
Pointers to refence materials, gruesome hack suggestions & patches are also
welcome.

{
	BTW, Excellent Job to all those responsible for merging laptop stuff into
	4.2. I swore by PAO and a 3.5 world, until a misguided mod and a misplaced 
	"make" burned my house down yesterday. (And me with no recent tape. Sheesh.)  
	PAO was fine but 4.2 is downright dandy.
}

pccardc(8) dumpcis (below) returns (lots of stuff including) a curious string :

	Max twin cards = 0

(Probably obvious, but I hope not.)

[ Donning IEEE LART stick suit and ISO grade RTFM helmet just in case ]

The cards in question: (qty=2) "Socket" ("Serial Port Card Rev 2.4"), 
function ID 2

Laptop Hardware: Toshiba Satellite 1695 CDT  ( dmesg attached below )
Kernel: Generic

[ 1 ]. The 1st card inserted is recognized, but fails to attach to a driver 
until an entry is added to /etc/pccard.conf ( This is probably expectable ):

# Socket Serial Card
card "Socket" "Serial Port Card Rev 2.4"
	config	auto "sio" ?
	reset	100 

After which, the 1st socket card recognized attaches to sio4. 

[ 2 ].  Upon insertion of (or booting with the) 2nd Socket card, the 2nd card
is recognized, but an attempt to attach fails with this message:

Mar 21 10:39:29 dialup /kernel: pccard: card inserted, slot 1
Mar 21 10:39:35 dialup pccardd[53]: Card "Socket"("Serial Port Card Rev 2.4") \
 [(null)] [(null)] matched "Socket" ("Serial Port Card Rev 2.4") [(null)] [(null)] 

Mar 21 10:39:35 dialup pccardd[53]: No free configuration for card Socket

SIDE ISSUES AND TANGENTAL CURIOUS SYMPTOMS:

[ 3 ]. Actually testing the one successfully attached card on sio4, with an
ordinary external modem,  no 2nd card inserted, it appears to function, albeit 
a bit sluggishly.  Characters typed to the connected device (modem) are echoed 
to the terminal 1 character behind entry. (Type 'A' see nothing. Type 'T' see 'A'. 
Type <return> see 'T'. type <return> see 'OK'. Hmm.) I am using cu(1) to perform
this test. I haven't had time to actually dial out on this modem to road test
for further symptoms or general performance quality. 


[ 4 ]. I have also noticed that my 3C589D card, when attached AFTER 1 Socket 
card,  seems to not work ( attaches, but won't send packets). No complaints 
mind you, I simply make sure the 3C589D is in the 1st slot, everything is A-OK. 
This was a sanity test just to see how different cards behaved together.

Thanks

G. Boyd

Director In Charge of Hey You In There My EMail Quit Working
(Keep That 20-lb Handbag Off Of The CAT-5 Cable -- Sector)
(Don't Unplug That Hub Again -- THAT Hub, Dammit--  Division)

mobile@vta.com

dumpcis:

Configuration data for card in slot 0
Tuple #1, code = 0x1 (Common memory descriptor), length = 3
    000:  00 00 ff
	Common memory device information:
		Device number 1, type No device, WPS = OFF
		Speed = No speed, Memory block size = 512b, 1 units
Tuple #2, code = 0x10 (Checksum), length = 5
    000:  07 00 d1 00 2c
	Checksum from offset 7, length 209, value is 0x2c
Tuple #3, code = 0x17 (Attribute memory descriptor), length = 3
    000:  d2 3a ff
	Attribute memory device information:
		Device number 1, type Function specific, WPS = OFF
		Speed = 200nS, Memory block size = 8Kb, 8 units
Tuple #4, code = 0x14 (No link), length = 0
Tuple #5, code = 0x20 (Manufacturer ID), length = 4
    000:  04 01 01 00
	PCMCIA ID = 0x104, OEM ID = 0x1
Tuple #6, code = 0x21 (Functional ID), length = 2
    000:  02 01
	Serial port/modem - POST initialize
Tuple #7, code = 0x22 (Functional EXT), length = 4
    000:  00 02 0f 7f
	Serial interface extension:
		16550 UART, Parity - Space,Mark,Odd,Even
		Data bit - 5bit,6bit,7bit,8bit, Stop bit - 1bit,1.5bit,2bit
Tuple #8, code = 0x15 (Version 1 info), length = 35
    000:  05 00 53 6f 63 6b 65 74 00 53 65 72 69 61 6c 20
    010:  50 6f 72 74 20 43 61 72 64 20 52 65 76 20 32 2e
    020:  34 00 ff
	Version = 5.0, Manuf = [Socket], card vers = [Serial Port Card Rev 2.4]
Tuple #9, code = 0x1a (Configuration map), length = 5
    000:  01 2d 00 04 03
	Reg len = 2, config register addr = 0x400, last config = 0x2d
	Registers: XX------ 
Tuple #10, code = 0x1b (Configuration entry), length = 27
    000:  cd 41 99 7f 55 4d 5d 1d 2d 2c 22 b0 60 f8 03 07
    010:  30 ff ff 20 c1 05 43 4f 4d 31 00
	Config index = 0xd(default)
	Interface byte = 0x41 (I/O)  +RDY/-BSY active
	Vcc pwr:
		Nominal operating supply voltage: 5 x 1V
		Minimum operating supply voltage: 4.5 x 1V
		Maximum operating supply voltage: 5.5 x 1V
		Continuous supply current: 1.5 x 10mA
		Max current average over 1 second: 2.5 x 10mA
		Max current average over 10 ms: 2.5 x 1mA
		Power down supply current: 2 x 10uA
	Card decodes 16 address lines, 8 Bit I/O only
		I/O address # 1: block start = 0x3f8 block length = 0x8
		IRQ modes: Level
		IRQs:  0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
	Max twin cards = 0
	Misc attr: (Power down supported)
Tuple #11, code = 0x1b (Configuration entry), length = 27
    000:  d5 41 99 7f 55 4d 5d 1d 2d 2c 22 b0 60 f8 02 07
    010:  30 ff ff 20 c1 05 43 4f 4d 32 00
	Config index = 0x15(default)
	Interface byte = 0x41 (I/O)  +RDY/-BSY active
	Vcc pwr:
		Nominal operating supply voltage: 5 x 1V
		Minimum operating supply voltage: 4.5 x 1V
		Maximum operating supply voltage: 5.5 x 1V
		Continuous supply current: 1.5 x 10mA
		Max current average over 1 second: 2.5 x 10mA
		Max current average over 10 ms: 2.5 x 1mA
		Power down supply current: 2 x 10uA
	Card decodes 16 address lines, 8 Bit I/O only
		I/O address # 1: block start = 0x2f8 block length = 0x8
		IRQ modes: Level
		IRQs:  0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
	Max twin cards = 0
	Misc attr: (Power down supported)
Tuple #12, code = 0x1b (Configuration entry), length = 27
    000:  dd 41 99 7f 55 4d 5d 1d 2d 2c 22 b0 60 e8 03 07
    010:  30 ff ff 20 c1 05 43 4f 4d 33 00
	Config index = 0x1d(default)
	Interface byte = 0x41 (I/O)  +RDY/-BSY active
	Vcc pwr:
		Nominal operating supply voltage: 5 x 1V
		Minimum operating supply voltage: 4.5 x 1V
		Maximum operating supply voltage: 5.5 x 1V
		Continuous supply current: 1.5 x 10mA
		Max current average over 1 second: 2.5 x 10mA
		Max current average over 10 ms: 2.5 x 1mA
		Power down supply current: 2 x 10uA
	Card decodes 16 address lines, 8 Bit I/O only
		I/O address # 1: block start = 0x3e8 block length = 0x8
		IRQ modes: Level
		IRQs:  0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
	Max twin cards = 0
	Misc attr: (Power down supported)
Tuple #13, code = 0x1b (Configuration entry), length = 27
    000:  e5 41 99 7f 55 4d 5d 1d 2d 2c 22 b0 60 e8 02 07
    010:  30 ff ff 20 c1 05 43 4f 4d 34 00
	Config index = 0x25(default)
	Interface byte = 0x41 (I/O)  +RDY/-BSY active
	Vcc pwr:
		Nominal operating supply voltage: 5 x 1V
		Minimum operating supply voltage: 4.5 x 1V
		Maximum operating supply voltage: 5.5 x 1V
		Continuous supply current: 1.5 x 10mA
		Max current average over 1 second: 2.5 x 10mA
		Max current average over 10 ms: 2.5 x 1mA
		Power down supply current: 2 x 10uA
	Card decodes 16 address lines, 8 Bit I/O only
		I/O address # 1: block start = 0x2e8 block length = 0x8
		IRQ modes: Level
		IRQs:  0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
	Max twin cards = 0
	Misc attr: (Power down supported)
Tuple #14, code = 0x1b (Configuration entry), length = 23
    000:  ed 41 99 7f 55 4d 5d 1d 2d 2c 22 23 30 ff ff 20
    010:  c1 05 43 4f 4d 58 00
	Config index = 0x2d(default)
	Interface byte = 0x41 (I/O)  +RDY/-BSY active
	Vcc pwr:
		Nominal operating supply voltage: 5 x 1V
		Minimum operating supply voltage: 4.5 x 1V
		Maximum operating supply voltage: 5.5 x 1V
		Continuous supply current: 1.5 x 10mA
		Max current average over 1 second: 2.5 x 10mA
		Max current average over 10 ms: 2.5 x 1mA
		Power down supply current: 2 x 10uA
	Card decodes 3 address lines, 8 Bit I/O only
		IRQ modes: Level
		IRQs:  0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
	Max twin cards = 0
	Misc attr: (Power down supported)
Tuple #15, code = 0xff (Terminator), length = 0
Configuration data for card in slot 1
Tuple #1, code = 0x1 (Common memory descriptor), length = 3
    000:  00 00 ff
	Common memory device information:
		Device number 1, type No device, WPS = OFF
		Speed = No speed, Memory block size = 512b, 1 units
Tuple #2, code = 0x10 (Checksum), length = 5
    000:  07 00 d1 00 2c
	Checksum from offset 7, length 209, value is 0x2c
Tuple #3, code = 0x17 (Attribute memory descriptor), length = 3
    000:  d2 3a ff
	Attribute memory device information:
		Device number 1, type Function specific, WPS = OFF
		Speed = 200nS, Memory block size = 8Kb, 8 units
Tuple #4, code = 0x14 (No link), length = 0
Tuple #5, code = 0x20 (Manufacturer ID), length = 4
    000:  04 01 01 00
	PCMCIA ID = 0x104, OEM ID = 0x1
Tuple #6, code = 0x21 (Functional ID), length = 2
    000:  02 01
	Serial port/modem - POST initialize
Tuple #7, code = 0x22 (Functional EXT), length = 4
    000:  00 02 0f 7f
	Serial interface extension:
		16550 UART, Parity - Space,Mark,Odd,Even
		Data bit - 5bit,6bit,7bit,8bit, Stop bit - 1bit,1.5bit,2bit
Tuple #8, code = 0x15 (Version 1 info), length = 35
    000:  05 00 53 6f 63 6b 65 74 00 53 65 72 69 61 6c 20
    010:  50 6f 72 74 20 43 61 72 64 20 52 65 76 20 32 2e
    020:  34 00 ff
	Version = 5.0, Manuf = [Socket], card vers = [Serial Port Card Rev 2.4]
Tuple #9, code = 0x1a (Configuration map), length = 5
    000:  01 2d 00 04 03
	Reg len = 2, config register addr = 0x400, last config = 0x2d
	Registers: XX------ 
Tuple #10, code = 0x1b (Configuration entry), length = 27
    000:  cd 41 99 7f 55 4d 5d 1d 2d 2c 22 b0 60 f8 03 07
    010:  30 ff ff 20 c1 05 43 4f 4d 31 00
	Config index = 0xd(default)
	Interface byte = 0x41 (I/O)  +RDY/-BSY active
	Vcc pwr:
		Nominal operating supply voltage: 5 x 1V
		Minimum operating supply voltage: 4.5 x 1V
		Maximum operating supply voltage: 5.5 x 1V
		Continuous supply current: 1.5 x 10mA
		Max current average over 1 second: 2.5 x 10mA
		Max current average over 10 ms: 2.5 x 1mA
		Power down supply current: 2 x 10uA
	Card decodes 16 address lines, 8 Bit I/O only
		I/O address # 1: block start = 0x3f8 block length = 0x8
		IRQ modes: Level
		IRQs:  0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
	Max twin cards = 0
	Misc attr: (Power down supported)
Tuple #11, code = 0x1b (Configuration entry), length = 27
    000:  d5 41 99 7f 55 4d 5d 1d 2d 2c 22 b0 60 f8 02 07
    010:  30 ff ff 20 c1 05 43 4f 4d 32 00
	Config index = 0x15(default)
	Interface byte = 0x41 (I/O)  +RDY/-BSY active
	Vcc pwr:
		Nominal operating supply voltage: 5 x 1V
		Minimum operating supply voltage: 4.5 x 1V
		Maximum operating supply voltage: 5.5 x 1V
		Continuous supply current: 1.5 x 10mA
		Max current average over 1 second: 2.5 x 10mA
		Max current average over 10 ms: 2.5 x 1mA
		Power down supply current: 2 x 10uA
	Card decodes 16 address lines, 8 Bit I/O only
		I/O address # 1: block start = 0x2f8 block length = 0x8
		IRQ modes: Level
		IRQs:  0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
	Max twin cards = 0
	Misc attr: (Power down supported)
Tuple #12, code = 0x1b (Configuration entry), length = 27
    000:  dd 41 99 7f 55 4d 5d 1d 2d 2c 22 b0 60 e8 03 07
    010:  30 ff ff 20 c1 05 43 4f 4d 33 00
	Config index = 0x1d(default)
	Interface byte = 0x41 (I/O)  +RDY/-BSY active
	Vcc pwr:
		Nominal operating supply voltage: 5 x 1V
		Minimum operating supply voltage: 4.5 x 1V
		Maximum operating supply voltage: 5.5 x 1V
		Continuous supply current: 1.5 x 10mA
		Max current average over 1 second: 2.5 x 10mA
		Max current average over 10 ms: 2.5 x 1mA
		Power down supply current: 2 x 10uA
	Card decodes 16 address lines, 8 Bit I/O only
		I/O address # 1: block start = 0x3e8 block length = 0x8
		IRQ modes: Level
		IRQs:  0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
	Max twin cards = 0
	Misc attr: (Power down supported)
Tuple #13, code = 0x1b (Configuration entry), length = 27
    000:  e5 41 99 7f 55 4d 5d 1d 2d 2c 22 b0 60 e8 02 07
    010:  30 ff ff 20 c1 05 43 4f 4d 34 00
	Config index = 0x25(default)
	Interface byte = 0x41 (I/O)  +RDY/-BSY active
	Vcc pwr:
		Nominal operating supply voltage: 5 x 1V
		Minimum operating supply voltage: 4.5 x 1V
		Maximum operating supply voltage: 5.5 x 1V
		Continuous supply current: 1.5 x 10mA
		Max current average over 1 second: 2.5 x 10mA
		Max current average over 10 ms: 2.5 x 1mA
		Power down supply current: 2 x 10uA
	Card decodes 16 address lines, 8 Bit I/O only
		I/O address # 1: block start = 0x2e8 block length = 0x8
		IRQ modes: Level
		IRQs:  0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
	Max twin cards = 0
	Misc attr: (Power down supported)
Tuple #14, code = 0x1b (Configuration entry), length = 23
    000:  ed 41 99 7f 55 4d 5d 1d 2d 2c 22 23 30 ff ff 20
    010:  c1 05 43 4f 4d 58 00
	Config index = 0x2d(default)
	Interface byte = 0x41 (I/O)  +RDY/-BSY active
	Vcc pwr:
		Nominal operating supply voltage: 5 x 1V
		Minimum operating supply voltage: 4.5 x 1V
		Maximum operating supply voltage: 5.5 x 1V
		Continuous supply current: 1.5 x 10mA
		Max current average over 1 second: 2.5 x 10mA
		Max current average over 10 ms: 2.5 x 1mA
		Power down supply current: 2 x 10uA
	Card decodes 3 address lines, 8 Bit I/O only
		IRQ modes: Level
		IRQs:  0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
	Max twin cards = 0
	Misc attr: (Power down supported)
Tuple #15, code = 0xff (Terminator), length = 0
2 slots found


dmesg output ( /var/log/messages ):

Mar 21 10:37:56 dialup /kernel: Copyright (c) 1992-2000 The FreeBSD Project.
Mar 21 10:37:56 dialup /kernel: Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
Mar 21 10:37:56 dialup /kernel: The Regents of the University of California. All rights reserved.
Mar 21 10:37:56 dialup /kernel: FreeBSD 4.2-RELEASE #0: Mon Nov 20 13:02:55 GMT 2000
Mar 21 10:37:56 dialup /kernel: jkh@bento.FreeBSD.org:/usr/src/sys/compile/GENERIC
Mar 21 10:37:56 dialup /kernel: Timecounter "i8254"  frequency 1193182 Hz
Mar 21 10:37:56 dialup /kernel: CPU: Pentium III/Pentium III Xeon/Celeron (597.07-MHz 686-class CPU)
Mar 21 10:37:56 dialup /kernel: Origin = "GenuineIntel"  Id = 0x683  Stepping = 3
Mar 21 10:37:56 dialup /kernel: Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
Mar 21 10:37:56 dialup /kernel: real memory  = 67043328 (65472K bytes)
Mar 21 10:37:56 dialup /kernel: avail memory = 61018112 (59588K bytes)
Mar 21 10:37:56 dialup /kernel: Preloaded elf kernel "kernel" at 0xc0436000.
Mar 21 10:37:56 dialup /kernel: Pentium Pro MTRR support enabled
Mar 21 10:37:56 dialup /kernel: md0: Malloc disk
Mar 21 10:37:56 dialup /kernel: npx0: <math processor> on motherboard
Mar 21 10:37:56 dialup /kernel: npx0: INT 16 interface
Mar 21 10:37:56 dialup /kernel: pcib0: <Intel 82443BX (440 BX) host to PCI bridge> on motherboard
Mar 21 10:37:56 dialup /kernel: pci0: <PCI bus> on pcib0
Mar 21 10:37:56 dialup /kernel: pcib1: <Intel 82443BX (440 BX) PCI-PCI (AGP) bridge> at device 1.0 on pci0
Mar 21 10:37:56 dialup /kernel: pci1: <PCI bus> on pcib1
Mar 21 10:37:56 dialup /kernel: pci1: <ATI model 4c42 graphics accelerator> at 0.0 irq 10
Mar 21 10:37:56 dialup /kernel: pcic-pci0: <TI PCI-1420 PCI-CardBus Bridge> at device 4.0 on pci0
Mar 21 10:37:56 dialup /kernel: pcic-pci0: TI12XX PCI Config Reg: [speaker enable][pwr save][FUNC pci int + CSC serial isa irq]
Mar 21 10:37:56 dialup /kernel: pcic-pci1: <TI PCI-1420 PCI-CardBus Bridge> at device 4.1 on pci0
Mar 21 10:37:56 dialup /kernel: pcic-pci1: TI12XX PCI Config Reg: [speaker enable][pwr save][FUNC pci int + CSC serial isa irq]
Mar 21 10:37:56 dialup /kernel: isab0: <Intel 82371AB PCI to ISA bridge> at device 7.0 on pci0
Mar 21 10:37:56 dialup /kernel: isa0: <ISA bus> on isab0
Mar 21 10:37:56 dialup /kernel: atapci0: <Intel PIIX4 ATA33 controller> port 0x1050-0x105f at device 7.1 on pci0
Mar 21 10:37:56 dialup /kernel: ata0: at 0x1f0 irq 14 on atapci0
Mar 21 10:37:56 dialup /kernel: ata1: at 0x170 irq 15 on atapci0
Mar 21 10:37:56 dialup /kernel: uhci0: <Intel 82371AB/EB (PIIX4) USB controller> irq 10 at device 7.2 on pci0
Mar 21 10:37:56 dialup /kernel: uhci0: Could not map ports
Mar 21 10:37:56 dialup /kernel: device_probe_and_attach: uhci0 attach returned 6
Mar 21 10:37:56 dialup /kernel: chip1: <Intel 82371AB Power management controller> port 0x1040-0x104f at device 7.3 on pci0
Mar 21 10:37:56 dialup /kernel: pci0: <unknown card> (vendor=0x1013, dev=0x6005) at 8.0 irq 5
Mar 21 10:37:56 dialup /kernel: pci0: <unknown card> (vendor=0x127a, dev=0x2013) at 16.0 irq 10
Mar 21 10:37:56 dialup /kernel: fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
Mar 21 10:37:56 dialup /kernel: fdc0: FIFO enabled, 8 bytes threshold
Mar 21 10:37:56 dialup /kernel: fd0: <1440-KB 3.5" drive> on fdc0 drive 0
Mar 21 10:37:56 dialup /kernel: atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
Mar 21 10:37:56 dialup /kernel: atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
Mar 21 10:37:56 dialup /kernel: kbd0 at atkbd0
Mar 21 10:37:56 dialup /kernel: psm0: <PS/2 Mouse> irq 12 on atkbdc0
Mar 21 10:37:56 dialup /kernel: psm0: model Generic PS/2 mouse, device ID 0
Mar 21 10:37:56 dialup /kernel: vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Mar 21 10:37:56 dialup /kernel: sc0: <System console> at flags 0x100 on isa0
Mar 21 10:37:56 dialup /kernel: sc0: VGA <16 virtual consoles, flags=0x300>
Mar 21 10:37:56 dialup /kernel: pcic0: <VLSI 82C146> at port 0x3e0 iomem 0xd0000 on isa0
Mar 21 10:37:56 dialup /kernel: pcic0: Polling mode
Mar 21 10:37:56 dialup /kernel: pccard0: <PC Card bus -- kludge version> on pcic0
Mar 21 10:37:56 dialup /kernel: pccard1: <PC Card bus -- kludge version> on pcic0
Mar 21 10:37:56 dialup /kernel: sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
Mar 21 10:37:56 dialup /kernel: sio0: type 16550A
Mar 21 10:37:56 dialup /kernel: sio1: configured irq 3 not in bitmap of probed irqs 0
Mar 21 10:37:56 dialup /kernel: ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
Mar 21 10:37:56 dialup /kernel: ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
Mar 21 10:37:56 dialup /kernel: plip0: <PLIP network interface> on ppbus0
Mar 21 10:37:56 dialup /kernel: lpt0: <Printer> on ppbus0
Mar 21 10:37:56 dialup /kernel: lpt0: Interrupt-driven port
Mar 21 10:37:56 dialup /kernel: ppi0: <Parallel I/O> on ppbus0
Mar 21 10:37:56 dialup /kernel: ad0: 5729MB <FUJITSU MHK2060AT> [12416/15/63] at ata0-master UDMA33
Mar 21 10:37:56 dialup /kernel: acd0: CDROM <TOSHIBA CD-ROM XM-7002Bc> at ata1-master using PIO4
Mar 21 10:37:56 dialup /kernel: Mounting root from ufs:/dev/ad0s2a
Mar 21 10:37:56 dialup /kernel: pccard: card inserted, slot 1
Mar 21 10:38:00 dialup pccardd[53]: Card "3Com Corporation"("3C589D") [TP/BNC LAN Card Ver. 2a] [000002] matched "3Com Corporation" ("3C589") [(null)] [(null)] 
Mar 21 10:38:05 dialup /kernel: ep0: <3Com Etherlink III 3C589> at port 0x240-0x24f irq 3 slot 1 on pccard1
Mar 21 10:38:05 dialup /kernel: ep0: Ethernet address 00:10:4b:a0:e3:41
Mar 21 10:38:05 dialup pccardd[53]: ep0: 3Com Corporation (3C589) inserted.
Mar 21 10:38:05 dialup pccardd[53]: pccardd started
Mar 21 10:38:16 dialup login: ROOT LOGIN (root) ON ttyv0
Mar 21 10:38:41 dialup /kernel: pccard: card inserted, slot 0
Mar 21 10:38:46 dialup pccardd[53]: Card "Socket"("Serial Port Card Rev 2.4") [(null)] [(null)] matched "Socket" ("Serial Port Card Rev 2.4") [(null)] [(null)] 
Mar 21 10:38:51 dialup /kernel: sio4 at port 0x2f8-0x2ff irq 5 slot 0 on pccard0
Mar 21 10:38:51 dialup /kernel: sio4: type 16550A
Mar 21 10:38:51 dialup pccardd[53]: sio4: Socket (Serial Port Card Rev 2.4) inserted.
Mar 21 10:39:16 dialup /kernel: ep0: detached
Mar 21 10:39:16 dialup /kernel: pccard: card removed, slot 1
Mar 21 10:39:16 dialup /kernel: stray irq 3
Mar 21 10:39:16 dialup pccardd[53]: ep0: 3Com Corporation (3C589) removed.
Mar 21 10:39:29 dialup /kernel: pccard: card inserted, slot 1
Mar 21 10:39:35 dialup pccardd[53]: Card "Socket"("Serial Port Card Rev 2.4") [(null)] [(null)] matched "Socket" ("Serial Port Card Rev 2.4") [(null)] [(null)] 
Mar 21 10:39:35 dialup pccardd[53]: No free configuration for card Socket
Mar 21 10:39:54 dialup /kernel: pccard: card removed, slot 1
Mar 21 10:40:07 dialup /kernel: pccard: card inserted, slot 1
Mar 21 10:40:13 dialup pccardd[53]: Card "3Com Corporation"("3C589D") [TP/BNC LAN Card Ver. 2a] [000002] matched "3Com Corporation" ("3C589") [(null)] [(null)] 
Mar 21 10:40:18 dialup /kernel: ep0: <3Com Etherlink III 3C589> at port 0x240-0x24f irq 3 slot 1 on pccard1
Mar 21 10:40:18 dialup /kernel: ep0: Ethernet address 00:10:4b:a0:e3:41
Mar 21 10:40:18 dialup pccardd[53]: ep0: 3Com Corporation (3C589) inserted.

EOF


To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-mobile" in the body of the message




Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?200103212159.QAA57943>