Date: Wed, 8 Sep 2004 15:56:15 +0400 From: Ighor <mail@furgon-center.ru> To: "Andras Kende" <andras@kende.com>, questions@freebsd.org Subject: Re[2]: Intel PRO/1000 and Intel 865 PE, FreeBSD 5.2.1 Message-ID: <478585937.20040908155615@furgon-center.ru> In-Reply-To: <E1BxTYF-0005CQ-00.andras-kende-com@mx15.mail.ru> References: <1698934765.20040818131741@mail.ru> <E1BxTYF-0005CQ-00.andras-kende-com@mx15.mail.ru>
next in thread | previous in thread | raw e-mail | index | archive | help
*This message was transferred with a trial version of CommuniGate(tm) Pro* Good day, Andras. 18 aug 2004 , 20:44:42: AK> -----Original Message----- AK> From: owner-freebsd-questions@freebsd.org AK> [mailto:owner-freebsd-questions@freebsd.org] On Behalf Of Ighor AK> Sent: Wednesday, August 18, 2004 4:18 AM AK> To: questions@FreeBSD.org AK> Subject: Intel PRO/1000 and Intel 865 PE, FreeBSD 5.2.1 AK> Good day! AK> Sorry about my stupid questions, but i can't resolve my problem by AK> myself. I've read a lot of pages and FAQs but can't do this: AK> I have Intel PRO/1000 Network Card on Albatron motherb PX865PE ProII AK> oard with Inter 82865PE chipset. AK> After boot network card doesn't work. I think it's something with AK> interrupts. It only works when I disable ACPI in device.hints. The the AK> card uses IRQ18 and all is ok. AK> I've shitched resources in BIOS in thousands combinations - it's all AK> the same. AK> I need ACPI for HT pseudo-dual processing. AK> There are two logs attached - with ACPI and without AK> Thank you if you can help me. AK> Hello Ighor, AK> I had an Intel 865PERL Board + P4 3.0 800 HTT CPU AK> 5.2.1 always crashed because some ACPI compatibility problem... AK> I upgraded to a 5.2 Current which solved the ACPI issues. AK> Replaced that board to a ASUS p4c800-e deluxe which never had any problem AK> since.. AK> Try firmware upgrade on the motherboard or try test with Current AK> Best regards, AK> Andras Kende AK> http://www.kende.com I've changed motherboard to Albatron on i865PE and 3Com NIC (xl driver). Now it says: === ... Sep 7 18:49:23 kernel: pci0: <serial bus, USB> at device 29.7 (no driver attached) Sep 7 18:49:23 kernel: pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0 Sep 7 18:49:23 kernel: pci2: <ACPI PCI bus> on pcib2 Sep 7 18:49:23 kernel: xl0: <3Com 3c905C-TX Fast Etherlink XL> port 0xa000-0xa07f mem 0xfb000000-0xfb00007f irq 20 at device 0.0 on pci2 Sep 7 18:49:23 kernel: xl0: Ethernet address: 00:0a:48:0c:89:a3 Sep 7 18:49:23 kernel: xl0: no PHY found! Sep 7 18:49:23 kernel: device_probe_and_attach: xl0 attach returned 6 ... === And still does not work. Hardware is 100% ok. I'm panic. -- Best regards, Ighor Poterakhin ICQ UIN 65975280, phone +7-916-7219187
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?478585937.20040908155615>