Skip site navigation (1)Skip section navigation (2)
Date:      Fri, 17 Jun 2022 18:30:07 -0500
From:      Larry Rosenman <ler@lerctr.org>
To:        Michael Gmelin <grembo@freebsd.org>
Cc:        Alexander Motin <mav@freebsd.org>, Freebsd current <freebsd-current@freebsd.org>
Subject:   Re: SAS/SATA controllers: 8 port that support 8TB Drives
Message-ID:  <5936c6368df3c7d762d4710d23e7c57c@lerctr.org>
In-Reply-To: <736314DA-354C-465C-8D8C-AF67AAD68F5D@freebsd.org>
References:  <f31ff2942ca3d3f1389f21157986ce46@lerctr.org> <736314DA-354C-465C-8D8C-AF67AAD68F5D@freebsd.org>

next in thread | previous in thread | raw e-mail | index | archive | help
On 06/17/2022 6:20 pm, Michael Gmelin wrote:
>> On 18. Jun 2022, at 00:57, Larry Rosenman <ler@lerctr.org> wrote:
>> On 06/17/2022 5:48 pm, Michael Gmelin wrote:
>>>> On 18. Jun 2022, at 00:31, Alexander Motin <mav@freebsd.org> wrote:
>>>> 
>>>>> On 17.06.2022 18:24, Alexander Motin wrote:
>>>>>> On 17.06.2022 18:16, Larry Rosenman wrote:
>>>>>> On 06/17/2022 5:08 pm, Alexander Motin wrote:
>>>>>>> On 17.06.2022 11:59, Larry Rosenman wrote:
>>>>>>>> I'm looking to upgrade the controllers in my TrueNAS box to 
>>>>>>>> something that will
>>>>>>>> support 8TB drives because apparently my LSI 2108 controllers do 
>>>>>>>> not support 8TB drives.
>>>>>>>> What's the communities recommendation?
>>>>>>>> needs to support SFF connectors for a total of 4 SFF connectors, 
>>>>>>>> as I have 16 slots.
>>>>>>> We at iX are still using LSI/Broadcom HBAs, just moved from long
>>>>>>> discontinued mps(4) to newer mpr(4).  And I don't believe the 
>>>>>>> problem
>>>>>>> is directly related to capacity.  According to my observations it 
>>>>>>> may
>>>>>>> be Seagate HDDs of/above certain (8TB) generation.  We do not use
>>>>>>> Seagate HDDs in our products, so about that instability I only 
>>>>>>> heard
>>>>>>> from forums and TrueNAS community user reports.
>>>>>> This is a mfi(4) set of controllers, and a ST80000Nm0045 8TB (CMR) 
>>>>>> drive.
>>>>>> Is this a bad combo?
>>>>>> mfi0: 9973 (708793330s/0x0002/WARN) - PD 00(e0xfc/s3) is not 
>>>>>> supported
>>>>>> (probe0:mfi0:0:0:0): INQUIRY. CDB: 12 00 00 00 24 00
>>>>>> (probe0:mfi0:0:0:0): CAM status: CCB request completed with an 
>>>>>> error
>>>>>> (probe0:mfi0:0:0:0): Retrying command, 3 more tries remain
>>>>>> (probe0:mfi0:0:0:0): INQUIRY. CDB: 12 00 00 00 24 00
>>>>>> (probe0:mfi0:0:0:0): CAM status: CCB request completed with an 
>>>>>> error
>>>>>> (probe0:mfi0:0:0:0): Retrying command, 2 more tries remain
>>>>>> (probe0:mfi0:0:0:0): INQUIRY. CDB: 12 00 00 00 24 00
>>>>>> (probe0:mfi0:0:0:0): CAM status: CCB request completed with an 
>>>>>> error
>>>>>> (probe0:mfi0:0:0:0): Retrying command, 1 more tries remain
>>>>>> (probe0:mfi0:0:0:0): INQUIRY. CDB: 12 00 00 00 24 00
>>>>>> (probe0:mfi0:0:0:0): CAM status: CCB request completed with an 
>>>>>> error
>>>>>> (probe0:mfi0:0:0:0): Retrying command, 0 more tries remain
>>>>>> (probe0:mfi0:0:0:0): INQUIRY. CDB: 12 00 00 00 24 00
>>>>>> (probe0:mfi0:0:0:0): CAM status: CCB request completed with an 
>>>>>> error
>>>>>> (probe0:mfi0:0:0:0): Error 5, Retries exhausted
>>>>>> mfi0 Physical Drives:
>>>>>>  0 (  932G) UNCONFIGURED GOOD <ST8000NM0045-1RL UG07 
>>>>>> serial=ZA1AC912> SATA E1:S3
>>>>> mfi(4) are RAIDs, not HBAs.  We do not recommend RAIDs with TrueNAS 
>>>>> due to problems with hot-plug, disk identification, etc. and so 
>>>>> have limited experience with them.  But I know some of LSI RAIDs 
>>>>> can be reflashed into equivalent HBAs, so if they share the 
>>>>> hardware, I can speculate that they may share some issues.
>>>> I've just noticed "932G" instead of "8000G".  It is obviously a 
>>>> bigger problem than what we heard for HBAs.  It looks like a kind of 
>>>> problems that should not happen to HBAs, since they should not care 
>>>> about disk capacity.
>>> What does `smartctl -a <device>` report (especially sector sizes)?
>>> -m
>>>> --
>>>> Alexander Motin
>> It's not even making a mfid* node (it is a 4Kn disk)
> 
> Ok, that’s sad (and explains the wrong size calculation as 4096/512=8).
> 
> Is this in HBA mode? (Like Alexander suggested, re-/crossflashing
> using an IT firmware might be an option). What controller / firmware
> image version is it?
> 
> -m
> 
> 
>> --
>> Larry Rosenman                     http://www.lerctr.org/~ler
>> Phone: +1 214-642-9640                 E-Mail: ler@lerctr.org
>> US Mail: 5708 Sabbia Dr, Round Rock, TX 78665-2106


mfi0@pci0:8:0:0:	class=0x010400 rev=0x05 hdr=0x00 vendor=0x1000 
device=0x0079 subvendor=0x1734 subdevice=0x1176
     vendor     = 'Broadcom / LSI'
     device     = 'MegaRAID SAS 2108 [Liberator]'
     class      = mass storage
     subclass   = RAID

mfi1@pci0:3:0:0:	class=0x010400 rev=0x05 hdr=0x00 vendor=0x1000 
device=0x0079 subvendor=0x1734 subdevice=0x1176
     vendor     = 'Broadcom / LSI'
     device     = 'MegaRAID SAS 2108 [Liberator]'
     class      = mass storage
     subclass   = RAID

mfi0: <LSI MegaSAS Gen2> port 0xd000-0xd0ff mem 
0xfbc9c000-0xfbc9ffff,0xfbcc0000
-0xfbcfffff irq 26 at device 0.0 on pci3
mfi0: Using MSI
mfi0: Megaraid SAS driver Ver 4.23
mfi0: FW MaxCmds = 1008, limiting to 128
mfip0: <SCSI Passthrough Bus> on mfi0
mfi0: 10014 (708822708s/0x0020/info) - Shutdown command received from 
host
mfi0: 10015 (boot + 3s/0x0020/info) - Firmware initialization started 
(PCI ID 00
79/1000/1176/1734)
mfi0: 10016 (boot + 3s/0x0020/info) - Firmware version 2.130.353-2727
mfi0: 10017 (boot + 6s/0x0020/info) - Package version 12.12.0-0174
mfi0: 10018 (boot + 6s/0x0020/info) - Board Revision

mfi1: <LSI MegaSAS Gen2> port 0xc000-0xc0ff mem 
0xfba9c000-0xfba9ffff,0xfbac0000
-0xfbafffff irq 16 at device 0.0 on pci8
mfi1: Using MSI
mfi1: Megaraid SAS driver Ver 4.23
mfi1: FW MaxCmds = 1008, limiting to 128


-- 
Larry Rosenman                     http://www.lerctr.org/~ler
Phone: +1 214-642-9640                 E-Mail: ler@lerctr.org
US Mail: 5708 Sabbia Dr, Round Rock, TX 78665-2106



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?5936c6368df3c7d762d4710d23e7c57c>