Date: Fri, 12 Sep 2014 13:02:49 -0300 From: Danilo Egea Gondolfo <daniloegea@yahoo.com.br> To: Ian Lepore <ian@FreeBSD.org> Cc: freebsd-arm@freebsd.org Subject: Re: panic: run_interrupt_driven_config_hooks: waited to long on 10.1-PRERELEASE + RPI-B Message-ID: <54131929.10208@yahoo.com.br> In-Reply-To: <1410444341.1150.439.camel@revolution.hippie.lan> References: <1410382322.23950.YahooMailNeo@web162003.mail.bf1.yahoo.com> <1410444341.1150.439.camel@revolution.hippie.lan>
next in thread | previous in thread | raw e-mail | index | archive | help
On 09/11/14 11:05, Ian Lepore wrote: > On Wed, 2014-09-10 at 13:52 -0700, Danilo Egea wrote: >> Hi all, >> >> I updated my system on raspberry to 10.0-PRERELEASE (r271400) and now the system is stopping at this point [1]. >> This is a known problem? >> >> Sorry the bad quality picture... >> >> [1] - https://www.dropbox.com/sc/r89hs2wal7dpn44/AABCKqJzAB7FzlHugfUvQrUva > I sync'd to the same stable-10 revision and built a fresh world and > kernel and it boots fine. The big difference is that I don't use a > video console, just serial. I don't know if that's a factor in why you > see a hang or not. > > -- Ian > > > Ok, now I have a serial cable. Now it's freezing and I can't run a "bt". I noticed these lines: "VT: initialize with new VT driver "fb". device_attach: fbd0 attach returned 6 fb0: Failed to attach fbd device" With other kernel config I got this bt: http://pastebin.com/FUVCwt7B Hit [Enter] to boot immediately, or any other key for command prompt. Booting [/boot/kernel/kernel]... Using DTB provided by U-Boot at address 0x0x100. Kernel entry at 0x100100... Kernel args: (null) KDB: debugger backends: ddb KDB: current backend: ddb Copyright (c) 1992-2014 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 10.1-BETA1 #0 r271466: Fri Sep 12 11:41:47 BRT 2014 root@danilo:/home/danilo/Mestrado/Sources/crochet-freebsd/work/obj/arm.armv6/home/danilo/Sources/freebsd-10-stable/sys/RPI-B arm FreeBSD clang version 3.4.1 (tags/RELEASE_34/dot1-final 208032) 20140512 VT: init without driver. CPU: ARM1176JZ-S rev 7 (ARM11J core) Supported features: ARM_ISA THUMB2 JAZELLE ARMv4 Security_Ext WB enabled LABT branch prediction enabled 16KB/32B 4-way instruction cache 16KB/32B 4-way write-back-locking-C data cache real memory = 536866816 (511 MB) avail memory = 482893824 (460 MB) random device not loaded; using insecure entropy random: <Software, Yarrow> initialized kbd0 at kbdmux0 ofwbus0: <Open Firmware Device Tree> simplebus0: <Flattened device tree simple bus> mem 0x20000000-0x20ffffff on ofwbus0 intc0: <BCM2835 Interrupt Controller> mem 0xb200-0xb3ff on simplebus0 systimer0: <BCM2835 System Timer> mem 0x3000-0x3fff irq 8,9,10,11 on simplebus0 Event timer "BCM2835 Event Timer 3" frequency 1000000 Hz quality 1000 Timecounter "BCM2835 Timecounter" frequency 1000000 Hz quality 1000 bcmwd0: <BCM2708/2835 Watchdog> mem 0x10001c-0x100027 on simplebus0 gpio0: <BCM2708/2835 GPIO controller> mem 0x200000-0x2000af irq 57,59,58,60 on simplebus0 gpio0: read-only pins: 46,47,48,49,50,51,52,53. gpio0: reserved pins: 48,49,50,51,52,53. gpioc0: <GPIO controller> on gpio0 gpiobus0: <OFW GPIO bus> on gpio0 gpioled0: <GPIO led> at pin(s) 16 on gpiobus0 iichb0: <BCM2708/2835 BSC controller> mem 0x205000-0x20501f irq 61 on simplebus0 iicbus0: <OFW I2C bus> on iichb0 iic0: <I2C generic I/O> on iicbus0 iichb1: <BCM2708/2835 BSC controller> mem 0x804000-0x80401f irq 61 on simplebus0 iicbus1: <OFW I2C bus> on iichb1 iic1: <I2C generic I/O> on iicbus1 spi0: <BCM2708/2835 SPI controller> mem 0x204000-0x20401f irq 62 on simplebus0 spibus0: <OFW SPI bus> on spi0 bcm_dma0: <BCM2835 DMA Controller> mem 0x7000-0x7fff,0xe05000-0xe05fff irq 24,25,26,27,28,29,30,31,32,33,34,35,36 on simplebus0 mbox0: <BCM2835 VideoCore Mailbox> mem 0xb880-0xb8bf irq 1 on simplebus0 sdhci_bcm0: <Broadcom 2708 SDHCI controller> mem 0x300000-0x3000ff irq 70 on simplebus0 mmc0: <MMC/SD bus> on sdhci_bcm0 uart0: <PrimeCell UART (PL011)> mem 0x201000-0x201fff irq 65 on simplebus0 uart0: console (115200,n,8,1) dwcotg0: <DWC OTG 2.0 integrated USB controller> mem 0x980000-0x99ffff irq 17 on simplebus0 usbus0 on dwcotg0 fb0: <BCM2835 VT framebuffer driver> on ofwbus0 simplebus1: <Flattened device tree simple bus> on ofwbus0 simplebus1: could not get ranges device_attach: simplebus1 attach returned 6 Timecounters tick every 10.000 msec usbus0: 480Mbps High Speed USB v2.0 ugen0.1: <DWCOTG> at usbus0 uhub0: <DWCOTG OTG Root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0 mmcsd0: 4GB <SDHC SA04G 1.0 SN 1A93CC12 MFG 07/2012 by 2 TM> at mmc0 50.0MHz/4bit/65535-block fb0: 656x416(0x0@0,0) 16bpp fb0: pitch 1312, base 0x5e006000, screen_size 545792 fbd0 on fb0 VT: initialize with new VT driver "fb". device_attach: fbd0 attach returned 6 fb0: Failed to attach fbd device uhub0: 1 port with 1 removable, self powered ugen0.2: <vendor 0x0424> at usbus0 uhub1: <vendor 0x0424 product 0x9514, class 9/0, rev 2.00/2.00, addr 2> on usbus0 uhub1: MTT enabled uhub1: 5 ports with 4 removable, self powered random: unblocking device. ugen0.3: <vendor 0x0424> at usbus0 smsc0: <vendor 0x0424 product 0xec00, rev 2.00/2.00, addr 3> on usbus0 smsc0: chip 0xec00, rev. 0002 miibus0: <MII bus> on smsc0 ukphy0: <Generic IEEE 802.3u media interface> PHY 1 on miibus0 ukphy0: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto ue0: <USB Ethernet> on smsc0 ue0: Ethernet address: b8:27:eb:60:d9:9b run_interrupt_driven_hooks: still waiting after 60 seconds for bcm_fb_init run_interrupt_driven_hooks: still waiting after 120 seconds for bcm_fb_init run_interrupt_driven_hooks: still waiting after 180 seconds for bcm_fb_init run_interrupt_driven_hooks: still waiting after 240 seconds for bcm_fb_init run_interrupt_driven_hooks: still waiting after 300 seconds for bcm_fb_init
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?54131929.10208>