Date: Tue, 2 Jul 1996 15:47:54 -0600 (MDT) From: Greg Skafte <skafte@worldgate.com> To: freebsd-stable@freebsd.org Subject: Kernel Compile Problems Message-ID: <199607022147.PAA10597@gras-varg.worldgate.com>
next in thread | raw e-mail | index | archive | help
Hi guys with the Following config file generates some errors...
#
# $Id: GRAS-VARG,v 1.4 1996/07/26 11:30:37 skafte Exp $
#
# NB: You probably don't want to try running a kernel built from this
# file. Instead, you should start from GENERIC, and add options from
# this file as required.
#
#
# This directive is mandatory; it defines the architecture to be
# configured for; in this case, the 386 family. You must also specify
# at least one CPU (the one you intend to run on); deleting the
# specification for CPUs you don't need to use may make parts of the
# system run faster
#
machine "i386"
cpu "I486_CPU"
#
# This is the ``identification'' of the kernel. Usually this should
# be the same as the name of your kernel.
#
ident GRAS_VARG
#
# The `maxusers' parameter controls the static sizing of a number of
# internal system tables by a complicated formula defined in param.c.
#
maxusers 16
#
# Under some circumstances it is necessary to make the default max
# number of processes per user and open files per user more than the
# defaults on bootup. (an example is a large news server in which
# the uid, news, can sometimes need > 100 simultaneous processes running,
# or perhaps a user using lots of windows under X).
options "CHILD_MAX=128"
options "OPEN_MAX=128"
#
# A math emulator is mandatory if you wish to run on hardware which
# does not have a floating-point processor. Pick either the original,
# bogus (but freely-distributable) math emulator, or a much more
# fully-featured but GPL-licensed emulator taken from Linux.
#
#options MATH_EMULATE #Support for x87 emulation
#options GPL_MATH_EMULATE #Support for x87 emualtion via
#new math emulator
#
# This directive defines a number of things:
# - The compiled kernel is to be called `kernel'
# - The root filesystem might be on partition wd0a
# - Crash dumps will be written to wd0b, if possible. Specifying the
# dump device here is not recommended. Use dumpon(8).
#
# config kernel root on wd0 dumps on wd0
config kernel root on wd1
#####################################################################
# COMPATIBILITY OPTIONS
#
# Implement system calls compatible with 4.3BSD and older versions of
# FreeBSD.
#
options "COMPAT_43"
#
# Allow user-mode programs to manipulat their local descriptor tables.
# This option is required for the WINE Windows(tm) emulator, and is
# not used by anything else (that we know of).
#
# options USER_LDT #allow user-level control of i386 ldt
#
# These three options provide support for System V Interface
# Definition-style interprocess communication, in the form of shared
# memory, semaphores, and message queues, respectively.
#
options SYSVSHM
options SYSVSEM
options SYSVMSG
#####################################################################
# DEBUGGING OPTIONS
#
# Enable the kernel debugger.
#
# options DDB
#
# KTRACE enables the system-call tracing facility ktrace(2).
#
options KTRACE #kernel tracing
#
# The DIAGNOSTIC option is used in a number of source files to enable
# extra sanity checking of internal structures. This support is not
# enabled by default because of the extra time it would take to check
# for these conditions, which can only occur as a result of
# programming errors.
#
# options DIAGNOSTIC
#
# Allow ordinary users to take the console - this is useful for X.
options UCONSOLE
#####################################################################
# NETWORKING OPTIONS
#
# Protocol families:
# Only the INET (Internet) family is officially supported in FreeBSD.
# Source code for the NS (Xerox Network Service), ISO (OSI), and
# CCITT (X.25) families is provided for amusement value, although we
# try to ensure that it actually compiles.
#
options INET #Internet communications protocols
# options CCITT #X.25 network layer
# options NS #Xerox NS communications protocols
# These are currently broken and don't compile
#options ISO
#options TPIP #ISO TP class 4 over IP
#options TPCONS #ISO TP class 0 over X.25
#
# Network interfaces:
# The `loop' pseudo-device is mandatory when networking is enabled.
# The `ether' pseudo-device provides generic code to handle
# Ethernets; it is mandatory when a Ethernet device driver is
# configured.
# The 'fddi' pseudo-device provides generic code to support FDDI.
# The `sppp' pseudo-device serves a similar role for certain types
# of synchronous PPP links (like `cx').
# The `sl' pseudo-device implements the Serial Line IP (SLIP) service.
# The `ppp' pseudo-device implements the Point-to-Point Protocol.
# The `bpfilter' pseudo-device enables the Berkeley Packet Filter. Be
# aware of the legal and administrative consequences of enabling this
# option. The number of devices determines the maximum number of
# simultaneous BPF clients programs runnable.
# The `disc' pseudo-device implements a minimal network interface,
# which throws away all packets sent and never receives any. It is
# included for testing purposes.
# The `tun' pseudo-device implements the User Process PPP (iijppp)
#
pseudo-device ether #Generic Ethernet
#pseudo-device fddi #Generic FDDI
#pseudo-device sppp #Generic Synchronous PPP
pseudo-device loop #Network loopback device
#pseudo-device sl 2 #Serial Line IP
#pseudo-device ppp 2 #Point-to-point protocol
pseudo-device bpfilter 4 #Berkeley packet filter
pseudo-device disc #Discard device
#pseudo-device tun 1 #Tunnel driver(user process ppp)
#options NSIP #XNS over IP
#options LLC #X.25 link layer for Ethernets
#options HDLC #X.25 link layer for serial lines
# broken
#options EON #ISO CLNP over IP
#
# Internet family options:
#
# TCP_COMPAT_42 causes the TCP code to emulate certain bugs present in
# 4.2BSD. This option should not be used unless you have a 4.2BSD
# machine and TCP connections fail.
#
# GATEWAY allows the machine to forward packets, and also configures
# larger static sizes of a number of system tables.
#
# MROUTING enables the kernel multicast packet forwarder, which works
# with mrouted(8).
#
# IPFIREWALL enables support for IP firewall construction, in
# conjunction with the `ipfw' program. IPFIREWALL_VERBOSE does
# the obvious thing.
#
# ARP_PROXYALL enables global proxy ARP. Beware! This can burn
# your house down! See netinet/if_ether.c for the gory details.
# (Eventually there will be a better management interface.)
#
#options "TCP_COMPAT_42" #emulate 4.2BSD TCP bugs
options GATEWAY #internetwork gateway
options MROUTING # Multicast routing
options IPFIREWALL #firewall
options IPFIREWALL_VERBOSE #print information about
# dropped packets
#options ARP_PROXYALL # global proxy ARP
#####################################################################
# FILESYSTEM OPTIONS
#
# Only the root, /usr, and /tmp filesystems need be statically
# compiled; everything else will be automatically loaded at mount
# time. (Exception: the UFS family---FFS, MFS, and LFS---cannot
# currently be demand-loaded.) Some people still prefer to statically
# compile other filesystems as well.
#
# NB: The LFS, PORTAL, and UNION filesystems are known to be buggy,
# and WILL panic your system if you attempt to do anything with them.
# They are included here as an incentive for some enterprising soul to
# sit down and fix them.
#
# Note: 4.4BSD NQNFS lease checking has relatively high cost for
# _local_ I/O as well as remote I/O. Don't use it unless you will
# using NQNFS.
#
# One of these is mandatory:
options FFS #Fast filesystem
options NFS #Network File System
# The rest are optional:
#options NQNFS #Enable NQNFS lease checking
options "CD9660" #ISO 9660 filesystem
#options FDESC #File descriptor filesystem
#options KERNFS #Kernel filesystem
#options LFS #Log filesystem
#options MFS #Memory File System
options MSDOSFS #MS DOS File System
#options NULLFS #NULL filesystem
#options PORTAL #Portal filesystem
options PROCFS #Process filesystem
#options UMAPFS #UID map filesystem
#options UNION #Union filesystem
# Make space in the kernel for a MFS rootfilesystem. Define to the number
# of kilobytes to reserve for the filesystem.
#options "MFS_ROOT=10"
# Allow this many swap-devices.
options "NSWAPDEV=20"
# Disk quotas are supported when this option is enabled. If you
# change the value of this option, you must do a `make clean' in your
# kernel compile directory in order to get a working kernel.
#
#options QUOTA #enable disk quotas
#####################################################################
# SCSI DEVICES
# SCSI DEVICE CONFIGURATION
# The SCSI subsystem consists of the `base' SCSI code, a number of
# high-level SCSI device `type' drivers, and the low-level host-adapter
# device drivers. The host adapters are listed in the ISA and PCI
# device configuration sections below.
#
# Beginning with FreeBSD 2.0.5 you can wire down your SCSI devices so
# that a given bus, target, and LUN always come on line as the same
# device unit. In earlier versions the unit numbers were assigned
# in the order that the devices were probed on the SCSI bus. This
# means that if you removed a disk drive, you may have had to rewrite
# your /etc/fstab file, and also that you had to be careful when adding
# a new disk as it may have been probed earlier and moved your device
# configuration around.
# This old behavior is maintained as the default behavior. The unit
# assignment begins with the first non-wired down unit for a device
# type. For example, if you wire a disk as "sd3" then the first
# non-wired disk will be assigned sd4.
# The syntax for wiring down devices is:
# controller scbus0 at ahc0 # Single bus device
# controller scbus1 at ahc1 bus 0 # Single bus device
# controller scbus3 at ahc2 bus 0 # Twin bus device
# controller scbus2 at ahc2 bus 1 # Twin bus device
# disk sd0 at scbus0 target 0 unit 0
# disk sd1 at scbus3 target 1
# disk sd2 at scbus2 target 3
# tape st1 at scbus1 target 6
# device cd0 at scbus?
# "units" (SCSI logical unit number) that are not specified are
# treated as if specified as LUN 0.
# All SCSI devices allocate as many units as are required.
# The "unknown" device (uk? in pre-2.0.5) is now part of the base SCSI
# configuration and doesn't have to be explicitly configured.
#controller scbus0 #base SCSI code
#device ch0 #SCSI media changers
#device sd0 #SCSI disks
#device st0 #SCSI tapes
#device cd0 #SCSI CD-ROMs
# XXX
# The `od' driver is unsupported in 2.1-stable. The SCSI subsystem
# here does not allow for SCSI type overrides (assigning a driver that
# differs from the type the SCSI device claims to be), thus it could
# not be tested on my reference SONY SMO drive. -- joerg
#
# However, it will most likely work fine.
#device od0
# The previous devices (ch, sd, st, cd) are recognized by config.
# config doesn't (and shouldn't) know about these newer ones,
# so we have to specify that they are on a SCSI bus with the "at scbus?"
# clause.
#device worm0 at scbus? # SCSI worm
#device pt0 at scbus? # SCSI processor type
#device sctarg0 at scbus? # SCSI target
# SCSI OPTIONS:
# SCSIDEBUG: When defined enables debugging macros
# NO_SCSI_SENSE: When defined disables sense descriptions (about 4k)
# SCSI_REPORT_GEOMETRY: Always report disk geometry at boot up instead
# of only when booting verbosely.
#options SCSIDEBUG
#options NO_SCSI_SENSE
#options SCSI_REPORT_GEOMETRY
#####################################################################
# MISCELLANEOUS DEVICES AND OPTIONS
#
# Of these, only the `log' device is truly mandatory. The `pty'
# device usually turns out to be ``effectively mandatory'', as it is
# required for `telnetd', `rlogind', `screen', `emacs', and `xterm',
# among others. The `isdn', `ii', `ity', `itel', and `ispy' devices
# are all required when ISDN support is used.
#
pseudo-device pty 32 #Pseudo ttys - can go as high as 64
pseudo-device speaker #Play IBM BASIC-style noises out your speaker
pseudo-device log #Kernel syslog interface (/dev/klog)
pseudo-device gzip #Exec gzipped a.out's
pseudo-device vn #Vnode driver (turns a file into a device)
pseudo-device snp 4 #Snoop device - to look at pty/vty/etc..
# These are non-optional for ISDN
#pseudo-device isdn
#pseudo-device ii 4
#pseudo-device ity 4
#pseudo-device itel 2
#pseudo-device ispy 1
#####################################################################
# HARDWARE DEVICE CONFIGURATION
# ISA and EISA devices:
# Currently there is no separate support for EISA. There should be.
# Micro Channel is not supported at all.
#
# Mandatory ISA devices: isa, sc or vt, npx
#
controller isa0
#
# Options for `isa':
#
# AUTO_EOI_1 enables the `automatic EOI' feature for the master 8259A
# interrupt controller. This saves about 1.25 usec for each interrupt.
# No problems are known to be caused by this option.
#
# AUTO_EOI_2 enables the `automatic EOI' feature for the slave 8259A
# interrupt controller. This saves about 1.25 usec for each interrupt.
# Automatic EOI is documented not to work for for the slave with the
# original i8259A, but it works for some clones and some integrated
# versions.
#
# BOUNCE_BUFFERS provides support for ISA DMA on machines with more
# than 16 megabytes of memory. It doesn't hurt on other machines.
# Some broken EISA and VLB hardware may need this, too.
#pseudo-device ccd 4 #Concatenated disk driver
#
# DUMMY_NOPS disables extra delays for some bus operations. The delays
# are mostly for older systems and aren't used consistently. Probably
# works OK on most EISA bus machines.
#
# TUNE_1542 enables the automatic ISA bus speed selection for the
# Adaptec 1542 boards. Does not work for all boards, use it with caution.
#
# BROKEN_KEYBOARD_RESET disables the use of the keyboard controller to
# reset the CPU for reboot. This is needed on some systems with broken
# keyboard controllers.
options "AUTO_EOI_1"
options "AUTO_EOI_2"
options BOUNCE_BUFFERS
#options DUMMY_NOPS
#options "TUNE_1542"
#options "BROKEN_KEYBOARD_RESET"
# Enable this and PCVT_FREEBSD for pcvt vt220 compatible console driver
device vt0 at isa? port "IO_KBD" tty irq 1 vector pcrint
options "PCVT_FREEBSD=210" # pcvt running on FreeBSD 2.0.5
options XSERVER # include code for XFree86
options FAT_CURSOR # start with block cursor
options PCVT_CTRL_ALT_DEL # allow three finger salute
options PCVT_EMU_MOUSE
# The syscons console driver (sco color console compatible) - default.
#device sc0 at isa? port "IO_KBD" tty irq 1 vector scintr
#
# Options for `sc':
#
# HARDFONTS allows the driver to load an ISO-8859-1 font to replace
# the default font in your display adapter's memory.
#
#options HARDFONTS
#
# MAXCONS is maximum number of virtual consoles, no more than 16
# default value: 12
#
#options "MAXCONS=12"
device npx0 at isa? port "IO_NPX" irq 13 vector npxintr
#
# Optional ISA and EISA devices:
#
#
# SCSI host adapters:
#
# aha: Adaptec 154x
# ahb: Adaptec 174x (See Eisa and PCI section below)
# ahc: Adaptec 274x/284x/294x (See Eisa and PCI section below)
# aic: Adaptec 152x and sound cards using the Adaptec AIC-6360 (slow!)
# bt: Most Buslogic controllers
# nca: ProAudioSpectrum cards using the NCR 5380 or Trantor T130
# uha: UltraStore 14F and 34F
# sea: Seagate ST01/02 8 bit controller (slow!)
# wds: Western Digital WD7000 controller (no scatter/gather!).
#
# Note that the order is important in order for Buslogic cards to be
# probed correctly.
#
#controller bt0 at isa? port "IO_BT0" bio irq ? vector bt_isa_intr
#controller aha0 at isa? port "IO_AHA0" bio irq ? drq 5 vector ahaintr
#controller uha0 at isa? port "IO_UHA0" bio irq ? drq 5 vector uhaintr
#controller aic0 at isa? port 0x340 bio irq 11 vector aicintr
#controller nca0 at isa? port 0x1f88 bio irq 10 vector ncaintr
#controller nca1 at isa? port 0x1f84
#controller nca2 at isa? port 0x1f8c
#controller nca3 at isa? port 0x1e88
#controller nca4 at isa? port 0x350 bio irq 5 vector ncaintr
#controller sea0 at isa? bio irq 5 iomem 0xdc000 iosiz 0x2000 vector seaintr
#controller wds0 at isa? port 0x350 bio irq 15 drq 6 vector wdsintr
#
# ST-506, ESDI, and IDE hard disks: `wdc' and `wd'
#
# NB: ``Enhanced IDE'' is NOT supported at this time.
#
# The flags fields are used to enable the multi-sector I/O and
# the 32BIT I/O modes. The flags may be used in either the controller
# definition or in the individual disk definitions. The controller
# definition is supported for the boot configuration stuff.
#
# Each drive has a 16 bit flags value defined:
# The low 8 bits are the maximum value for the multi-sector I/O,
# where 0xff defaults to the maximum that the drive can handle.
# The high bit of the 16 bit flags (0x8000) allows probing for
# 32 bit transfers.
#
# The flags field for the drives can be specified in the controller
# specification with the low 16 bits for drive 0, and the high 16 bits
# for drive 1.
# e.g.:
#controller wdc0 at isa? port "IO_WD1" bio irq 14 flags 0x00ff8004 vector wdintr
#
# specifies that drive 0 will be allowed to probe for 32 bit transfers and
# a maximum multi-sector transfer of 4 sectors, and drive 1 will not be
# allowed to probe for 32 bit transfers, but will allow multi-sector
# transfers up to the maximum that the drive supports.
#
#
controller wdc0 at isa? port "IO_WD1" bio irq 14 vector wdintr
disk wd0 at wdc0 drive 0
disk wd1 at wdc0 drive 1
#controller wdc1 at isa? port "IO_WD2" bio irq 15 vector wdintr
#disk wd2 at wdc1 drive 0
#disk wd3 at wdc1 drive 1
#
# Options for `wdc':
#
# ATAPI enables the support for ATAPI-compatible IDE devices
#
#options ATAPI #Enable ATAPI support for IDE bus
# IDE CD-ROM driver - requires wdc controller and ATAPI option
#device wcd0
#
# Standard floppy disk controllers and floppy tapes: `fdc', `fd', and `ft'
#
controller fdc0 at isa? port "IO_FD1" bio irq 6 drq 2 vector fdintr
#
# Activate this line instead of the fdc0 line above if you happen to
# have an Insight floppy tape. Probing them proved to be dangerous
# for people with floppy disks only, so it's "hidden" behind a flag:
#controller fdc0 at isa? port "IO_FD1" bio flags 1 irq 6 drq 2 vector fdintr
disk fd0 at fdc0 drive 0
#disk fd1 at fdc0 drive 1
#tape ft0 at fdc0 drive 2
#
# Options for `fd':
#
# FDSEEKWAIT selects a non-default head-settle time (i.e., the time to
# wait after a seek is performed). The default value (1/32 s) is
# usually sufficient. The units are inverse seconds, so a value of 16
# here means to wait 1/16th of a second; you should choose a power of
# two.
#
#options FDSEEKWAIT="16"
#
# Other standard PC hardware: `lpt', `mse', `psm', `sio', etc.
#
# lpt: printer port
# lpt specials:
# port can be specified as ?, this will cause the driver to scan
# the BIOS port list;
# the irq and vector clauses may be omitted, this
# will force the port into polling mode.
# mse: Logitech and ATI InPort bus mouse ports
# psm: PS/2 mouse port [note: conflicts with sc0/vt0, thus "conflicts" keywd]
# sio: serial ports (see sio(4))
device lpt0 at isa? port? tty irq 7 vector lptintr
#device lpt1 at isa? port "IO_LPT3" tty irq 5 vector lptintr
#device mse0 at isa? port 0x23c tty irq 5 vector mseintr
device psm0 at isa? port "IO_KBD" conflicts tty irq 12 vector psmintr
# Options for psm:
#options PSM_NO_RESET #don't reset mouse hardware (some laptops)
device sio0 at isa? port "IO_COM1" tty irq 4 vector siointr
device sio1 at isa? port "IO_COM2" tty irq 3 vector siointr
# Options for sio:
#options COMCONSOLE #prefer serial console to video console
#options COM_MULTIPORT #code for some cards with shared IRQs
#options DSI_SOFT_MODEM #code for DSI Softmodems
#options BREAK_TO_DEBUGGER #a BREAK on a comconsole goes to
#DDB, if available.
#
# Network interfaces: `cx', `ed', `el', `ep', `ie', `is', `le', `lnc'
#
# cx: Cronyx/Sigma multiport sync/async (with Cisco or PPP framing)
# ed: Western Digital and SMC 80xx; Novell NE1000 and NE2000; 3Com 3C503
# el: 3Com 3C501 (slow!)
# ep: 3Com 3C509 (buggy)
# fe: Fujitsu MB86960A/MB86965A Ethernet
# fea: DEC DEFEA EISA FDDI adapter
# ie: AT&T StarLAN 10 and EN100; 3Com 3C507; unknown NI5210
# le: Digital Equipment EtherWorks 2 and EtherWorks 3 (DEPCA, DE100,
# DE101, DE200, DE201, DE202, DE203, DE204, DE205, DE422)
# lnc: Lance/PCnet cards (Isolan, Novell NE2100, NE32-VL)
# ze: IBM/National Semiconductor PCMCIA ethernet controller.
# zp: 3Com PCMCIA Etherlink III (It does not require shared memory for
# send/receive operation, but it needs 'iomem' to read/write the
# attribute memory)
#
#device cx0 at isa? port 0x240 net irq 15 drq 7 vector cxintr
#device ed0 at isa? port 0x280 net irq 5 iomem 0xd8000 vector edintr
#device eg0 at isa? port 0x310 net irq 5 vector egintr
#device el0 at isa? port 0x300 net irq 9 vector elintr
device ep0 at isa? port 0x300 net irq 10 vector epintr
#device fe0 at isa? port 0x240 net irq ? vector feintr
#device fea0 at isa? net irq ? vector feaintr
#device ie0 at isa? port 0x360 net irq 7 iomem 0xd0000 vector ieintr
#device ix0 at isa? port 0x300 net irq 10 iomem 0xd0000 iosiz 32768 vector ixintr
#device le0 at isa? port 0x300 net irq 5 iomem 0xd0000 vector le_intr
#device lnc0 at isa? port 0x300 net irq 10 drq 0 vector lncintr
#device ze0 at isa? port 0x300 net irq 5 iomem 0xd8000 vector zeintr
#device zp0 at isa? port 0x300 net irq 10 iomem 0xd8000 vector zpintr
#
# ISDN drivers - `isdn'.
#
# Uncomment one (and only one) of the following two drivers for the appropriate
# ISDN device you have. For more information on what's considered appropriate
# for your given set of circumstances, please read
# /usr/src/gnu/usr.sbin/isdn/docs/INSTALL. It's a bit sparse at present, but
# it's the best we have right now. The snic driver is also disabled at present,
# waiting for someone to upgrade the driver to 2.0 (it's in /sys/gnu/scsi/).
#
#device nic0 at isa? port "IO_COM3" iomem 0xe0000 tty irq 9 vector nicintr
#device nnic0 at isa? port 0x150 iomem 0xe0000 tty irq 12 vector nnicintr
#
# Audio drivers: `snd', `sb', `pas', `gus', `pca'
#
# snd: Voxware sound support code
# sb: SoundBlaster PCM - SoundBlaster, SB Pro, SB16, ProAudioSpectrum
# sbxvi: SoundBlaster 16
# sbmidi: SoundBlaster 16 MIDI interface
# pas: ProAudioSpectrum PCM and MIDI
# gus: Gravis Ultrasound - Ultrasound, Ultrasound 16, Ultrasound MAX
# gusxvi: Gravis Ultrasound 16-bit PCM (do not use)
# mss: Microsoft Sound System
# opl: Yamaha OPL-2 and OPL-3 FM - SB, SB Pro, SB 16, ProAudioSpectrum
# uart: stand-alone 6850 UART for MIDI
# mpu: Roland MPU-401 stand-alone card
#
# Beware! The addresses specified below are also hard-coded in
# i386/isa/sound/sound_config.h. If you change the values here, you
# must also change the values in the include file.
#
# pca: PCM audio through your PC speaker
#
# If you don't have a lpt0 device at IRQ 7, you can remove the
# ``conflicts'' specification in the appropriate device entries below.
#
# If you have a GUS-MAX card and want to use the CS4231 codec on the
# card the drqs for the gus max must be 8 bit (1, 2, or 3).
#
# If you would like to use the full duplex option on the gus, then define
# flags to be the ``read dma channel''.
#
# options BROKEN_BUS_CLOCK #PAS-16 isn't working and OPTI chipset
# options SYMPHONY_PAS #PAS-16 isn't working and SYMPHONY chipset
# options EXCLUDE_SBPRO #PAS-16
# options "SBC_IRQ=5" #PAS-16. Must match irq on sb0 line.
# PAS16: The order of the pas0/sb0/opl0 is important since the
# sb emulation is enabled in the pas-16 attach.
#
# The i386/isa/sound/sound.doc has more information.
# Controls all sound devices
controller snd0
#device pas0 at isa? port 0x388 irq 10 drq 6 vector pasintr
device sb0 at isa? port 0x280 irq 5 conflicts drq 1 vector sbintr
device sbxvi0 at isa? drq 5
device sbmidi0 at isa? port 0x330
options "SBC_IRQ=5" # Must match irq on sb0 line.
#device gus0 at isa? port 0x220 irq 12 drq 1 vector gusintr
#device gus0 at isa? port 0x220 irq 12 drq 1 flags 0x3 vector gusintr
#device mss0 at isa? port 0x530 irq 10 drq 1 vector adintr
#device opl0 at isa? port 0x388 conflicts
#device mpu0 at isa? port 0x330 irq 6 drq 0
#device uart0 at isa? port 0x330 irq 5 vector "m6850intr"
# Not controlled by `snd'
device pca0 at isa? port IO_TIMER1 tty
#
# Miscellaneous hardware:
#
# mcd: Mitsumi CD-ROM
# scd: Sony CD-ROM
# matcd: Matsushita/Panasonic CD-ROM
# wt: Wangtek and Archive QIC-02/QIC-36 tape drives
# ctx: Cortex-I frame grabber
# apm: Laptop Advanced Power Management (experimental)
# spigot: The Creative Labs Video Spigot video-aquisition board
# meteor: Matrox Meteor video capture board
# cy: Cyclades serial driver
# dgb: Digiboard PC/Xi and PC/Xe series driver (ALPHA QUALITY!)
# gp: National Instruments AT-GPIB and AT-GPIB/TNT board
# asc: GI1904-based hand scanners, e.g. the Trust Amiscan Grey
# gsc: Genius GS-4500 hand scanner.
# joy: joystick
# labpc: National Instrument's Lab-PC and Lab-PC+
# rc: RISCom/8 multiport card
# tw: TW-523 power line interface for use with X-10 home control products
# si: Specialix SI/XIO 4-32 port terminal multiplexor
#
# Notes on APM
# Some APM implementations will not work with the `statistics clock'
# enabled, so it's disabled by default if the APM driver is enabled.
# However, this is not true for all laptops. Try removing the option
# APM_BROKEN_STATCLOCK and see if suspend/resume work
#
#
# Notes on the spigot:
# The video spigot is at 0xad6. This port address can not be changed.
# The irq values may only be 10, 11, or 15
# I/O memory is an 8kb region. Possible values are:
# 0a0000, 0a2000, ..., 0fffff, f00000, f02000, ..., ffffff
# Note that the start address must be on an even boundary.
# Notes on the Digiboard driver:
#
# The following flag values have special meanings:
# 0x01 - alternate layout of pins
# 0x02 - use the windowed PC/Xe in 64K mode
# Notes on the Specialix SI/XIO driver:
# **This is NOT a Specialix supported Driver!**
# The host card is memory, not IO mapped.
# The Rev 1 host cards use a 64K chunk, on a 32K boundary.
# The Rev 2 host cards use a 32K chunk, on a 32K boundary.
# The cards can use an IRQ of 11, 12 or 15.
#device mcd0 at isa? port 0x300 bio irq 10 vector mcdintr
# for the Sony CDU31/33A CDROM
#device scd0 at isa? port 0x230 bio
# for the soundblaster 16 multicd - up to 4 devices
controller matcd0 at isa? port 0x290 bio
#device wt0 at isa? port 0x300 bio irq 5 drq 1 vector wtintr
#device ctx0 at isa? port 0x230 iomem 0xd0000
#device spigot0 at isa? port 0xad6 irq 15 iomem 0xee000 vector spigintr
#device qcam0 at isa? port "IO_LPT3" tty
#device apm0 at isa?
#options APM_BROKEN_STATCLOCK
#device gp0 at isa? port 0x2c0 tty
#device gsc0 at isa? port "IO_GSC1" tty drq 3
device joy0 at isa? port "IO_GAME"
#device cy0 at isa? tty irq 10 iomem 0xd4000 iosiz 0x2000 vector cyintr
#device dgb0 at isa? port 0x220 iomem 0xfc0000 iosiz ? tty
#device labpc0 at isa? port 0x260 tty irq 5 vector labpcintr
#device rc0 at isa? port 0x220 tty irq 12 vector rcintr
# the port and irq for tw0 are fictitious
#device tw0 at isa? port 0x380 tty irq 11 vector twintr
#device si0 at isa? iomem 0xd0000 tty irq 12 vector siintr
#device asc0 at isa? port IO_ASC1 tty drq 3 irq 10 vector ascintr
#
# EISA devices:
#
# The EISA bus device is eisa0. It provides auto-detection and
# configuration support for all devices on the EISA bus.
#
# The `ahb' device provides support for the Adaptec 174X adapter.
#
# The `ahc' device provides support for the Adaptec 274X and 284X
# adapters. The 284X, although a VLB card responds to EISA probes.
#
#controller eisa0
#controller ahb0
#controller ahc0
#
# PCI devices:
#
# The main PCI bus device is `pci'. It provides auto-detection and
# configuration support for all devices on the PCI bus, using either
# configuration mode defined in the PCI specification.
#
# The `ahc' device provides support for the Adaptec 29/3940(U)(W)
# and motherboard based AIC7870/AIC7880 adapters
#
# The `ncr' device provides support for the NCR 53C810 and 53C825
# self-contained SCSI host adapters.
#
# The `de' device provides support for the Digital Equipment DC21040
# self-contained Ethernet adapter.
#
# The `fpa' device provides support for the Digital DEFPA PCI FDDI
# adapter. pseudo-device fddi is also needed.
#
# The PROBE_VERBOSE option enables a long listing of chip set registers
# for supported PCI chip sets (currently only intel Saturn and Mercury).
#
# The 'meteor' device is a PCI video capture board. It can also have the
# following options:
# options "METEOR_ALLOC_PAGES=xxx" preallocate kernel pages for data entry
# figure (ROWS*COLUMN*BYTES_PER_PIXEL*FRAME+PAGE_SIZE-1)/PAGE_SIZE
# options METEOR_DEALLOC_PAGES remove all allocated pages on close(2)
# options "METEOR_DEALLOC_ABOVE=xxx" remove all allocated pages above the
# specified amount. If this value is below the allocated amount no action
# taken
#
#controller pci0
#device ncr0
#device de0
#device fpa0
#device meteor0
#options PROBE_VERBOSE
#
# Laptop/Notebook options:
#
# See also:
# apm under `Miscellaneous hardare'
# options PSM_NO_RESET for the `psm' driver
# above.
# For older notebooks that signal a powerfail condition (external
# power supply dropped, or battery state low) by issuing an NMI:
#options POWERFAIL_NMI # make it beep instead of panicing
[compile deleted]
loading kernel
cd9660_lookup.o: Undefined symbol `_isonum_711' referenced from text segment
cd9660_lookup.o: Undefined symbol `_isonum_711' referenced from text segment
cd9660_lookup.o: Undefined symbol `_isonum_711' referenced from text segment
cd9660_lookup.o: Undefined symbol `_isonum_711' referenced from text segment
cd9660_node.o: Undefined symbol `_isonum_733' referenced from text segment
cd9660_node.o: Undefined symbol `_isonum_733' referenced from text segment
cd9660_node.o: Undefined symbol `_isonum_711' referenced from text segment
cd9660_node.o: Undefined symbol `_isonum_711' referenced from text segment
cd9660_node.o: Undefined symbol `_isonum_711' referenced from text segment
cd9660_node.o: Undefined symbol `_isonum_711' referenced from text segment
cd9660_node.o: Undefined symbol `_isonum_711' referenced from text segment
cd9660_node.o: More undefined symbol _isonum_711 refs follow
cd9660_node.o: Undefined symbol `_isonum_723' referenced from text segment
cd9660_node.o: Undefined symbol `_isonum_723' referenced from text segment
cd9660_node.o: Undefined symbol `_isonum_733' referenced from text segment
cd9660_rrip.o: Undefined symbol `_isonum_731' referenced from text segment
cd9660_rrip.o: Undefined symbol `_isonum_731' referenced from text segment
cd9660_rrip.o: Undefined symbol `_isonum_731' referenced from text segment
cd9660_rrip.o: Undefined symbol `_isonum_731' referenced from text segment
cd9660_rrip.o: Undefined symbol `_isonum_733' referenced from text segment
cd9660_rrip.o: Undefined symbol `_isonum_733' referenced from text segment
cd9660_rrip.o: Undefined symbol `_isonum_733' referenced from text segment
cd9660_rrip.o: Undefined symbol `_isonum_733' referenced from text segment
cd9660_rrip.o: Undefined symbol `_isonum_733' referenced from text segment
cd9660_rrip.o: Undefined symbol `_isonum_733' referenced from text segment
cd9660_rrip.o: More undefined symbol _isonum_733 refs follow
cd9660_vfsops.o: Undefined symbol `_isonum_723' referenced from text segment
*** Error code 1
Stop.
--
Email: skafte@worldgate.com Voice: +403 413 1910 Fax: +403 421 4929
#575 Sun Life Place * 10123 99 Street * Edmonton, AB * Canada * T5J 3H1
-- --
PGP 2.6.2 Key fingerprint = 42 9C 2C A8 4D 2B C9 C4 7D B6 00 B0 50 47 20 97
http://gras-varg.worldgate.com/~skafte/ http://www.worldgate.com/
-- --
When things can't get any worse, they simplify themselves by getting a whole
lot worse then complicated. A complete and utter disaster is the simplest
thing in the world; it's preventing one that's complex. (Janet Morris)
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?199607022147.PAA10597>