Date: Thu, 29 Apr 1999 01:19:56 -0500 From: John Lengeling <johnl@raccoon.com> To: freebsd-scsi@freebsd.org Subject: Problems with HP T20 SCSI Travan under FreeBSD 3.1 Message-ID: <3727FA0C.E3780714@raccoon.com>
next in thread | raw e-mail | index | archive | help
I have an HP T20 SCSI Travan tape driver under FreeBSD 3.1 connected to
an Adaptec 2940UW controller. Kernel sees the 2940 and the HP T20
drive. I created the device using MAKEDEV sa0. When I insert the
cartridge, the drive scans back and forth a bit like a QIC drive. Looks
like some other error was returned from the probe.
When I try to do anything with the drive like tar (tar -cvf /dev/rsa0)
or
mt status, I get:
LOAD UNLOAD CDB 1B 0 0 0 10
MEDIUM ERROR asc:15,2
Positioning Error detected by read of medium.
What is up? Will the T20 work under FreeBSD 3.1? I have included my
boot -v output. Is it specific to the HP T20, or will or will Exabyte
8200/8500s or HP 4MM drives work under 3.1?
10b7, dev=0x9058, revid=0x00
class=02-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=10
map[0]: type 4, range 32, base 0000ec00, size 7
map[1]: type 1, range 32, base febfef80, size 7
xl0: <3Com 3c905B-COMBO Fast Etherlink XL> rev 0x00 int a irq 10 on
pci0.19.0
xl0: Ethernet address: 00:50:04:66:84:22
xl0: media options word: 3a
xl0: probing for a PHY
xl0: checking address: 0
xl0: checking address: 1
xl0: checking address: 2
xl0: checking address: 3
xl0: checking address: 4
xl0: checking address: 5
xl0: checking address: 6
xl0: checking address: 7
xl0: checking address: 8
xl0: checking address: 9
xl0: checking address: 10
xl0: checking address: 11
xl0: checking address: 12
xl0: checking address: 13
xl0: checking address: 14
xl0: checking address: 15
xl0: checking address: 16
xl0: checking address: 17
xl0: checking address: 18
xl0: checking address: 19
xl0: checking address: 20
xl0: checking address: 21
xl0: checking address: 22
xl0: checking address: 23
xl0: checking address: 24
xl0: found PHY at address 24, vendor id: 0 device id: 0
xl0: PHY type: <MII-compliant physical interface>
xl0: found 10baseT
xl0: found AUI
xl0: found BNC
xl0: found 100baseTX
xl0: autoneg complete, link status good (half-duplex, 10Mbps)
bpf: xl0 attached
Probing for devices on PCI bus 1:
found-> vendor=0x1002, dev=0x4742, revid=0x5c
class=03-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[0]: type 1, range 32, base fd000000, size 24
map[1]: type 4, range 32, base 0000d800, size 8
map[2]: type 1, range 32, base feaff000, size 12
vga0: <ATI model 4742 graphics accelerator> rev 0x5c on pci1.0.0
Initializing PnP override table
Probing for PnP devices:
Trying Read_Port at 203
CSN 1 Vendor ID: CSC4236 [0x3642630e] Serial 0xffffffff Comp ID: @@@0000
[0x00000000]
Called nullpnp_probe with tag 0x00000001, type 0x3642630e
port 0x0000 0x0000 0x0000 0x0000 irq 0:0 drq 4:4 en 0
This is a CS4236, but LDN 0 is disabled
Probing for devices on the ISA bus:
atkbd: the current kbd controller command byte 0065
atkbd: keyboard ID 0x41ab (2)
kbdc: RESET_KBD return code:00fa
kbdc: RESET_KBD status:00aa
sc0 on isa
sc0: fb0 kbd0
sc0: VGA color <16 virtual consoles, flags=0x0>
atkbdc0 at 0x60-0x6f on motherboard
atkbd0 irq 1 on isa
kbd0: atkbd0, AT 101/102 (2), config:0x10000, flags:0x3d0000
psm0: current command byte:0065
kbdc: TEST_AUX_PORT status:0000
kbdc: RESET_AUX return code:00fa
kbdc: RESET_AUX status:00aa
kbdc: RESET_AUX ID:0000
psm: status 00 02 64
psm: status 00 00 64
psm: status 00 03 64
psm: status 00 03 64
psm: status 10 00 64
psm: data 08 00 00
psm: data 08 00 00
psm: status 00 02 64
psm0 irq 12 on isa
psm0: model Generic PS/2 mouse, device ID 0, 2 buttons
psm0: config:00000000, flags:00000000, packet size:3
psm0: syncmask:c0, syncbits:00
sio0: irq maps: 0x1 0x11 0x1 0x1
sio0 at 0x3f8-0x3ff irq 4 flags 0x10 on isa
sio0: type 16550A
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: irq maps: 0x1 0x1 0x1 0x1
sio1: probe failed test(s): 0 1 2 4 6 7 9
sio1 not found at 0x2f8
sio2: disabled, not probed.
sio3: disabled, not probed.
mss_probe: no address supplied, try default 0x530
mss_detect error, busy still set (0xff)
sb_probe: no address supplied, try defaults (0x220,0x240)
pcm0 not found
fdc0 at 0x3f0-0x3f7 irq 6 drq 2 on isa
fdc0: FIFO enabled, 8 bytes threshold
fd0: 1.44MB 3.5in
wdc0 at 0x1f0-0x1f7 irq 14 on isa
wdc0: unit 0 (wd0): <Maxtor 90432D2>
wd0: 4121MB (8440992 sectors), 8374 cyls, 16 heads, 63 S/T, 512 B/S
wd0: ATA INQUIRE valid = 0007, dmamword = 0007, apio = 0003, udma = 0407
wdc1 at 0x170-0x177 irq 15 on isa
wdc1: unit 0 (wd2): <Maxtor 90845D4>
wd2: 8063MB (16514064 sectors), 16383 cyls, 16 heads, 63 S/T, 512 B/S
wd2: ATA INQUIRE valid = 0007, dmamword = 0007, apio = 0003, udma = 0407
wdc1: unit 1 (atapi): <TOSHIBA DVD-ROM SD-M1202/1020>, removable, accel,
dma, iordis
acd0: drive speed 5512KB/sec, 256KB cache
acd0: supported read types: CD-R, CD-RW, CD-DA
acd0: Audio: play, 16 volume levels
acd0: Mechanism: ejectable tray
acd0: Medium: no/blank disc inside, unlocked
ppc: parallel port found at 0x378
ppc0: EPP SPP
ppc0 at 0x378 irq 7 on isa
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
nlpt0: <generic printer> on ppbus 0
nlpt0: Interrupt-driven port
ppi0: <generic parallel i/o> on ppbus 0
plip: irq 7
plip0: <PLIP network interface> on ppbus 0
bpf: lp0 attached
vga0 at 0x3b0-0x3df maddr 0xa0000 msize 131072 on isa
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3b0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xf00b8000 size:32k gran:32k, buf:0x0 size:0k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
npx0 on motherboard
npx0: INT 16 interface
apm0: disabled, not probed.
imasks: bio c008c040, tty c0071492, net c0071492
BIOS Geometries:
0:00000000 0..0=1 cylinders, 0..0=1 heads, 1..0=0 sectors
1:00000000 0..0=1 cylinders, 0..0=1 heads, 1..0=0 sectors
2:00000000 0..0=1 cylinders, 0..0=1 heads, 1..0=0 sectors
3:00000000 0..0=1 cylinders, 0..0=1 heads, 1..0=0 sectors
4:00000000 0..0=1 cylinders, 0..0=1 heads, 1..0=0 sectors
5:00000000 0..0=1 cylinders, 0..0=1 heads, 1..0=0 sectors
6:00000000 0..0=1 cylinders, 0..0=1 heads, 1..0=0 sectors
7:00000000 0..0=1 cylinders, 0..0=1 heads, 1..0=0 sectors
0 accounted for
Device configuration finished.
bpf: tun0 attached
bpf: sl0 attached
bpf: ppp0 attached
new masks: bio c008c040, tty c0071492, net c0071492
bpf: lo0 attached
Waiting 15 seconds for SCSI devices to settle
(noperiph:ahc0:0:-1:-1): SCSI bus reset delivered. 0 SCBs aborted.
ahc0: Selection Timeout on A:0. 1 SCBs aborted
ahc0: Selection Timeout on A:1. 1 SCBs aborted
ahc0: Selection Timeout on A:2. 1 SCBs aborted
ahc0: Selection Timeout on A:3. 1 SCBs aborted
ahc0: Selection Timeout on A:5. 1 SCBs aborted
ahc0: Selection Timeout on A:6. 1 SCBs aborted
ahc0: Selection Timeout on A:8. 1 SCBs aborted
ahc0: Selection Timeout on A:9. 1 SCBs aborted
ahc0: Selection Timeout on A:10. 1 SCBs aborted
ahc0: Selection Timeout on A:11. 1 SCBs aborted
ahc0: Selection Timeout on A:12. 1 SCBs aborted
ahc0: Selection Timeout on A:13. 1 SCBs aborted
ahc0: Selection Timeout on A:14. 1 SCBs aborted
ahc0: Selection Timeout on A:15. 1 SCBs aborted
(probe4:ahc0:0:4:0): INQUIRY. CDB: 12 1 80 0 ff 0
(probe4:ahc0:0:4:0): ILLEGAL REQUEST asc:24,0
(probe4:ahc0:0:4:0): Invalid field in CDB
sa0 at ahc0 bus 0 target 4 lun 0
sa0: <HP T20 3.00> Removable Sequential Access SCSI-2 device
sa0: 3.300MB/s transfers
pass0 at ahc0 bus 0 target 4 lun 0
pass0: <HP T20 3.00> Removable Sequential Access SCSI-2 device
pass0: 3.300MB/s transfers
Considering MFS root f/s.
No MFS image available as root f/s.
Considering FFS root f/s.
changing root device to wd0s1a
wd0s1: type 0xa5, start 63, end = 8434124, size 8434062 : OK
wd2s1: type 0xa5, start 63, end = 16514063, size 16514001 : OK
wd2s1: type 0xa5, start 63, end = 16514063, size 16514001 : OK
Linux-ELF exec handler installed
splash: image decoder found: logo_saver
(sa0:ahc0:0:4:0): LOAD UNLOAD. CDB: 1b 0 0 0 1 0
(sa0:ahc0:0:4:0): MEDIUM ERROR asc:15,2
(sa0:ahc0:0:4:0): Positioning error detected by read of medium
(sa0:ahc0:0:4:0): LOAD UNLOAD. CDB: 1b 0 0 0 1 0
(sa0:ahc0:0:4:0): MEDIUM ERROR asc:15,2
(sa0:ahc0:0:4:0): Positioning error detected by read of medium
(sa0:ahc0:0:4:0): LOAD UNLOAD. CDB: 1b 0 0 0 1 0
(sa0:ahc0:0:4:0): MEDIUM ERROR asc:15,2
(sa0:ahc0:0:4:0): Positioning error detected by read of medium
JohnL
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-scsi" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?3727FA0C.E3780714>