Skip site navigation (1)Skip section navigation (2)
Date:      Wed, 08 Nov 2006 19:21:14 +0300
From:      Boris Samorodov <bsam@ipt.ru>
To:        "Mark Maddox" <MMaddox@TMCDesign.com>
Cc:        freebsd-questions@freebsd.org
Subject:   Re: FreeBSD 6.1 Installation problem
Message-ID:  <58214693@srv.sem.ipt.ru>
In-Reply-To: <CE568152976C2A4BADD08770B6360E8A01D78803@tmcsvr.tmcdesign.local> (Mark Maddox's message of "Wed, 8 Nov 2006 09:00:30 -0700")
References:  <CE568152976C2A4BADD08770B6360E8A01D78803@tmcsvr.tmcdesign.local>

next in thread | previous in thread | raw e-mail | index | archive | help
On Wed, 8 Nov 2006 09:00:30 -0700 Mark Maddox wrote:
> > On Wed, 8 Nov 2006 08:02:14 -0700 Mark Maddox wrote:
> > 
> > > The cable is fine; I installed windows on the drive in the machine
> that is having problems, just to see if it would work.  I'm still
> > > trying
> to get FreeBSD 6.1 up
> >
> > > "Mark Maddox" <MMaddox@TMCDesign.com> writes:
> >
> > > > I have an onboard Intel ICH7-M SATA controller with an SATA hard
> drive and cdrom connected to it.  I am unable to install FreeBSD onto
> the harddrive.
> > > >
> > > > According to the FreeBSD website ICH7 has been supported since
> version 6.0
> > > > I have tried putting the controller in Legacy Mode and tried
> turning turned DMA off in on boot.  I have tested both of my SATA
> > > > ports on
> the motherboard to make sure they both work with an alternate
> operating system (Windows) and they both worked.
> > > >
> > > > I have also installed the harddrive in another computer and
> installed FreeBSD on it successfully and then (after testing it and
> > > > booting successfully on that computer) put it in the machine I
> > > > am having
> the problems with only to have it start booting and then error out
> with harddrive errors.
> > > >
> > > > During boot I get this error:
> > > > ad0: FAILURE -READ_DMA48 status=ff<BUSY,
> > > > READY,DMA_READY,DSC,DRQ,CORRECTABLE,INDEX,ERROR> error=0
> LBA=390721967
> > > >
> > > > During install the error I get is Error mounting /mnt/dev/ad0s1e
> on /mnt/tmp : Input/output error
> > > >
> > > > ad0: FAILURE - READ_DMA status=ff<BUSY,READY,
> > > > DMA_READY,DSC,DRQ,CORRECTABLE,INDEX,ERROR> error=0 LBA=9303631
> > > >
> > > > Anyone have any ideas?
> >
> > > Sounds like controller problems.  I'd start by replacing the SATA
> cable.
> >  Windows throws those messages away. And you understand it when the
> > data got lost.

> I just tried a new cable and I get the same errors.

> Windows worked fine on the machine, but I cannot use Windows for my
> application.

Do you have any check utility for your harddrive?
Can you try the latest FreeBSD iso installation CD (seems it's a
BETA-3 now)? Not for a production use but at least to test.


WBR
-- 
Boris Samorodov (bsam)
Research Engineer, http://www.ipt.ru Telephone & Internet SP
FreeBSD committer, http://www.FreeBSD.org The Power To Serve



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?58214693>