Date: Wed, 22 Jun 2011 09:39:16 -0700 From: Jack Vogel <jfvogel@gmail.com> To: Joshua Boyd <boydjd@jbip.net> Cc: freebsd-stable <freebsd-stable@freebsd.org>, "Vogel, Jack" <jack.vogel@intel.com>, Jeremy Chadwick <freebsd@jdc.parodius.com> Subject: Re: em0 watchdog timeouts on 8-STABLE Message-ID: <BANLkTi=6ssM3uMvkx3OqfbWJ0%2BaV75mXZg@mail.gmail.com> In-Reply-To: <BANLkTimcn2QcgiVq347%2BiX%2B0puxmFVurCw@mail.gmail.com> References: <BANLkTinoyV61RzkB8HbHe=AY8zsBov4JXg@mail.gmail.com> <20110615075754.GA54879@icarus.home.lan> <BANLkTim_Y30cXNtvOGg_%2Bj4devU5VtiMxA@mail.gmail.com> <BANLkTininFrihBXvsKwAnheqE%2B%2BXoyhCVg@mail.gmail.com> <BANLkTi=UPCZms5-t5vgXoS7-ZK4VkXWy8w@mail.gmail.com> <BANLkTi=DpPykyjUaG6KkDG=dQ=xqfOMEHg@mail.gmail.com> <BANLkTi=BgY2_SsL6tjSsoRXszffSddVXNA@mail.gmail.com> <BANLkTimcn2QcgiVq347%2BiX%2B0puxmFVurCw@mail.gmail.com>
next in thread | previous in thread | raw e-mail | index | archive | help
Then its sounding to me like the em driver is a victim of your other I/O, meaning that the watchdogs are just an honest indicator of the driver not getting to run when it needs to. This is also a side effect of running older hardware with legacy interrupts, the MSIX capable adapters would be less likely to get starved I suspect. I don't know anything about ZFS so maybe someone else can help with tuning this?? Jack On Wed, Jun 22, 2011 at 8:24 AM, Joshua Boyd <boydjd@jbip.net> wrote: > :( > > I don't actually have problems normally with maxing out the throughput of > the network. Watchdogs only occur when I've got heavy I/O occurring during > ZFS scrubs across 2 mpt devices, at about 700MB/s. And then it doesn't > matter what kind of traffic I'm running through em0, it still throws > watchdogs. During the first occurrence it was actually pretty minimal > traffic, less than 100KB/s. > > Are there any statistics that would be useful to you if I were to trigger > the watchdogs again? > > > On Wed, Jun 22, 2011 at 1:22 AM, Jack Vogel <jfvogel@gmail.com> wrote: > >> I cannot repro this, I used your kernel config, this is on a Dell 1850 >> btw, >> I ran netperf stress from 3 clients, and have seen no watchdogs :( >> >> Jack >> >> >> >> On Tue, Jun 21, 2011 at 7:59 PM, Joshua Boyd <boydjd@jbip.net> wrote: >> >>> If needed, I can reproduce this on demand. Just need to know what sort of >>> statistics are needed when the problem is occurring. I've had to turn off my >>> weekly scrubs until I can figure out how to fix this problem. >>> >>> >>> On Wed, Jun 15, 2011 at 8:37 PM, Joshua Boyd <boydjd@jbip.net> wrote: >>> >>>> In the kernel. Here's my kernel configuration: >>>> >>>> http://pastebin.com/raw.php?i=4JL814m3 >>>> >>>> On Wed, Jun 15, 2011 at 8:20 PM, Jack Vogel <jfvogel@gmail.com> wrote: >>>> >>>>> I have hardware now, am working on reproducing this. Just curious, do >>>>> you have >>>>> the em driver defined in the kernel, or as a module? >>>>> >>>>> Jack >>>>> >>>>> >>>>> On Wed, Jun 15, 2011 at 2:09 AM, Joshua Boyd <boydjd@jbip.net> wrote: >>>>> >>>>>> On Wed, Jun 15, 2011 at 3:57 AM, Jeremy Chadwick >>>>>> <freebsd@jdc.parodius.com>wrote: >>>>>> >>>>>> > On Wed, Jun 15, 2011 at 03:14:43AM -0400, Joshua Boyd wrote: >>>>>> > > I recently updated my server to the latest 8-STABLE, and upgraded >>>>>> to v28 >>>>>> > > ZFS. I have not had these problems on any other version of >>>>>> 8-STABLE or >>>>>> > > 7-STABLE, which this box was upgraded from some time ago. >>>>>> > > >>>>>> > > Now, during my weekly scrub, I get the following messages and em0 >>>>>> is >>>>>> > > unresponsive: >>>>>> > > >>>>>> > > Jun 12 03:07:58 foghornleghorn kernel: em0: Watchdog timeout -- >>>>>> resetting >>>>>> > > Jun 12 03:07:58 foghornleghorn kernel: em0: link state changed to >>>>>> DOWN >>>>>> > > Jun 12 03:08:01 foghornleghorn kernel: em0: link state changed to >>>>>> UP >>>>>> > > Jun 12 03:08:47 foghornleghorn kernel: em0: Watchdog timeout -- >>>>>> resetting >>>>>> > > Jun 12 03:08:47 foghornleghorn kernel: em0: link state changed to >>>>>> DOWN >>>>>> > > Jun 12 03:08:50 foghornleghorn kernel: em0: link state changed to >>>>>> UP >>>>>> > > >>>>>> > > My scrub is scheduled to start at 03:00:00, so it looks like >>>>>> watchdog >>>>>> > > timeouts start occurring pretty quickly once I/O ramps up. >>>>>> > > >>>>>> > > Here's some possibly relevant information, let me know if anything >>>>>> else >>>>>> > > would be helpful to troubleshoot. >>>>>> > > >>>>>> > > FreeBSD foghornleghorn.res.openband.net 8.2-STABLE FreeBSD >>>>>> 8.2-STABLE >>>>>> > #17: >>>>>> > > Mon Jun 6 19:40:19 EDT 2011 >>>>>> > > root@foghornleghorn.res.openband.net: >>>>>> /usr/obj/usr/src/sys/FOGHORNLEGHORN >>>>>> > > amd64 >>>>>> > > >>>>>> > > em0: <Intel(R) PRO/1000 Legacy Network Connection 1.0.3> port >>>>>> > 0xe800-0xe83f >>>>>> > > mem 0xfebe0000-0xfebfffff,0xfebc0000-0xfebdffff irq 20 at device >>>>>> 5.0 on >>>>>> > pci7 >>>>>> > > >>>>>> > > em0@pci0:7:5:0: class=0x020000 card=0x13768086 chip=0x107c8086 >>>>>> rev=0x05 >>>>>> > > hdr=0x00 >>>>>> > > vendor = 'Intel Corporation' >>>>>> > > device = 'Gigabit Ethernet Controller (Copper) rev 5 >>>>>> (82541PI)' >>>>>> > > class = network >>>>>> > > subclass = ethernet >>>>>> > > >>>>>> > > And, the SAS cards: >>>>>> > > >>>>>> > > dev.mpt.0.%desc: LSILogic SAS/SATA Adapter >>>>>> > > dev.mpt.0.%driver: mpt >>>>>> > > dev.mpt.0.%location: slot=0 function=0 >>>>>> > > dev.mpt.0.%pnpinfo: vendor=0x1000 device=0x0058 subvendor=0x15d9 >>>>>> > > subdevice=0xa580 class=0x010000 >>>>>> > > dev.mpt.0.%parent: pci1 >>>>>> > > dev.mpt.0.debug: 3 >>>>>> > > dev.mpt.0.role: 1 >>>>>> > > dev.mpt.1.%desc: LSILogic SAS/SATA Adapter >>>>>> > > dev.mpt.1.%driver: mpt >>>>>> > > dev.mpt.1.%location: slot=0 function=0 >>>>>> > > dev.mpt.1.%pnpinfo: vendor=0x1000 device=0x0058 subvendor=0x15d9 >>>>>> > > subdevice=0xa580 class=0x010000 >>>>>> > > dev.mpt.1.%parent: pci2 >>>>>> > > dev.mpt.1.debug: 3 >>>>>> > > dev.mpt.1.role: 1 >>>>>> > > dev.mpt.2.%desc: LSILogic SAS/SATA Adapter >>>>>> > > dev.mpt.2.%driver: mpt >>>>>> > > dev.mpt.2.%location: slot=0 function=0 >>>>>> > > dev.mpt.2.%pnpinfo: vendor=0x1000 device=0x0058 subvendor=0x1000 >>>>>> > > subdevice=0x30a0 class=0x010000 >>>>>> > > dev.mpt.2.%parent: pci6 >>>>>> > > dev.mpt.2.debug: 3 >>>>>> > > dev.mpt.2.role: 1 >>>>>> > >>>>>> > Please provide output from the following commands (as root): >>>>>> > >>>>>> > # pciconf -lvcb >>>>>> > >>>>>> >>>>>> hostb0@pci0:0:0:0: class=0x060000 card=0x59561002 chip=0x59561002 >>>>>> rev=0x00 >>>>>> hdr=0x00 >>>>>> vendor = 'ATI Technologies Inc. / Advanced Micro Devices, Inc.' >>>>>> device = 'RD790 GFX Dual Slot' >>>>>> class = bridge >>>>>> subclass = HOST-PCI >>>>>> pcib1@pci0:0:2:0: class=0x060400 card=0x59561002 chip=0x59781002 >>>>>> rev=0x00 >>>>>> hdr=0x01 >>>>>> vendor = 'ATI Technologies Inc. / Advanced Micro Devices, Inc.' >>>>>> device = 'RD790 PCI to PCI bridge (external gfx0 port A)' >>>>>> class = bridge >>>>>> subclass = PCI-PCI >>>>>> pcib2@pci0:0:3:0: class=0x060400 card=0x59561002 chip=0x59791002 >>>>>> rev=0x00 >>>>>> hdr=0x01 >>>>>> vendor = 'ATI Technologies Inc. / Advanced Micro Devices, Inc.' >>>>>> device = 'RD790 PCI to PCI bridge (external gfx0 port B)' >>>>>> class = bridge >>>>>> subclass = PCI-PCI >>>>>> pcib3@pci0:0:4:0: class=0x060400 card=0x59561002 chip=0x597a1002 >>>>>> rev=0x00 >>>>>> hdr=0x01 >>>>>> vendor = 'ATI Technologies Inc. / Advanced Micro Devices, Inc.' >>>>>> device = 'RD790 PCI to PCI bridge (PCIe gpp port A)' >>>>>> class = bridge >>>>>> subclass = PCI-PCI >>>>>> pcib4@pci0:0:6:0: class=0x060400 card=0x59561002 chip=0x597c1002 >>>>>> rev=0x00 >>>>>> hdr=0x01 >>>>>> vendor = 'ATI Technologies Inc. / Advanced Micro Devices, Inc.' >>>>>> device = 'RD790 PCI to PCI bridge (PCIe gpp port C)' >>>>>> class = bridge >>>>>> subclass = PCI-PCI >>>>>> pcib5@pci0:0:7:0: class=0x060400 card=0x59561002 chip=0x597d1002 >>>>>> rev=0x00 >>>>>> hdr=0x01 >>>>>> vendor = 'ATI Technologies Inc. / Advanced Micro Devices, Inc.' >>>>>> device = 'RD790 PCI to PCI bridge (PCIe gpp port D)' >>>>>> class = bridge >>>>>> subclass = PCI-PCI >>>>>> pcib6@pci0:0:11:0: class=0x060400 card=0x59561002 chip=0x59801002 >>>>>> rev=0x00 >>>>>> hdr=0x01 >>>>>> vendor = 'ATI Technologies Inc. / Advanced Micro Devices, Inc.' >>>>>> device = 'RD790 PCI to PCI bridge (external gfx1 port A)' >>>>>> class = bridge >>>>>> subclass = PCI-PCI >>>>>> atapci4@pci0:0:18:0: class=0x01018f card=0x81ef1043 chip=0x43801002 >>>>>> rev=0x00 >>>>>> hdr=0x00 >>>>>> vendor = 'ATI Technologies Inc. / Advanced Micro Devices, Inc.' >>>>>> device = 'IXP SB600 Serial ATA Controller' >>>>>> class = mass storage >>>>>> subclass = ATA >>>>>> ohci0@pci0:0:19:0: class=0x0c0310 card=0x82881043 chip=0x43871002 >>>>>> rev=0x00 >>>>>> hdr=0x00 >>>>>> vendor = 'ATI Technologies Inc. / Advanced Micro Devices, Inc.' >>>>>> device = 'IXP SB600 USB Controller (OHCI0)' >>>>>> class = serial bus >>>>>> subclass = USB >>>>>> ohci1@pci0:0:19:1: class=0x0c0310 card=0x82881043 chip=0x43881002 >>>>>> rev=0x00 >>>>>> hdr=0x00 >>>>>> vendor = 'ATI Technologies Inc. / Advanced Micro Devices, Inc.' >>>>>> device = 'IXP SB600 USB Controller (OHCI1)' >>>>>> class = serial bus >>>>>> subclass = USB >>>>>> ohci2@pci0:0:19:2: class=0x0c0310 card=0x82881043 chip=0x43891002 >>>>>> rev=0x00 >>>>>> hdr=0x00 >>>>>> vendor = 'ATI Technologies Inc. / Advanced Micro Devices, Inc.' >>>>>> device = 'IXP SB600 USB Controller (OHCI2)' >>>>>> class = serial bus >>>>>> subclass = USB >>>>>> ohci3@pci0:0:19:3: class=0x0c0310 card=0x82881043 chip=0x438a1002 >>>>>> rev=0x00 >>>>>> hdr=0x00 >>>>>> vendor = 'ATI Technologies Inc. / Advanced Micro Devices, Inc.' >>>>>> device = 'IXP SB600 USB Controller (OHCI3)' >>>>>> class = serial bus >>>>>> subclass = USB >>>>>> ohci4@pci0:0:19:4: class=0x0c0310 card=0x82881043 chip=0x438b1002 >>>>>> rev=0x00 >>>>>> hdr=0x00 >>>>>> vendor = 'ATI Technologies Inc. / Advanced Micro Devices, Inc.' >>>>>> device = 'IXP SB600 USB Controller (OHCI4)' >>>>>> class = serial bus >>>>>> subclass = USB >>>>>> ehci0@pci0:0:19:5: class=0x0c0320 card=0x82881043 chip=0x43861002 >>>>>> rev=0x00 >>>>>> hdr=0x00 >>>>>> vendor = 'ATI Technologies Inc. / Advanced Micro Devices, Inc.' >>>>>> device = 'IXP SB600 USB Controller (EHCI)' >>>>>> class = serial bus >>>>>> subclass = USB >>>>>> none0@pci0:0:20:0: class=0x0c0500 card=0x82881043 chip=0x43851002 >>>>>> rev=0x14 >>>>>> hdr=0x00 >>>>>> vendor = 'ATI Technologies Inc. / Advanced Micro Devices, Inc.' >>>>>> device = 'ATI SMBus (ATI RD600/RS600)' >>>>>> class = serial bus >>>>>> subclass = SMBus >>>>>> atapci5@pci0:0:20:1: class=0x01018a card=0x82881043 chip=0x438c1002 >>>>>> rev=0x00 >>>>>> hdr=0x00 >>>>>> vendor = 'ATI Technologies Inc. / Advanced Micro Devices, Inc.' >>>>>> device = 'ATI RD600/RS600 IDE Controller (RD600/RS600)' >>>>>> class = mass storage >>>>>> subclass = ATA >>>>>> none1@pci0:0:20:2: class=0x040300 card=0x82881043 chip=0x43831002 >>>>>> rev=0x00 >>>>>> hdr=0x00 >>>>>> vendor = 'ATI Technologies Inc. / Advanced Micro Devices, Inc.' >>>>>> device = 'IXP SB600 High Definition Audio Controller' >>>>>> class = multimedia >>>>>> subclass = HDA >>>>>> isab0@pci0:0:20:3: class=0x060100 card=0x82881043 chip=0x438d1002 >>>>>> rev=0x00 >>>>>> hdr=0x00 >>>>>> vendor = 'ATI Technologies Inc. / Advanced Micro Devices, Inc.' >>>>>> device = 'IXP SB600 PCI to LPC Bridge' >>>>>> class = bridge >>>>>> subclass = PCI-ISA >>>>>> pcib7@pci0:0:20:4: class=0x060401 card=0x00000000 chip=0x43841002 >>>>>> rev=0x00 >>>>>> hdr=0x01 >>>>>> vendor = 'ATI Technologies Inc. / Advanced Micro Devices, Inc.' >>>>>> device = 'IXP SB600 PCI to PCI Bridge' >>>>>> class = bridge >>>>>> subclass = PCI-PCI >>>>>> hostb1@pci0:0:24:0: class=0x060000 card=0x00000000 chip=0x12001022 >>>>>> rev=0x00 >>>>>> hdr=0x00 >>>>>> vendor = 'Advanced Micro Devices (AMD)' >>>>>> device = '(Family 10h) Athlon64/Opteron/Sempron HyperTransport >>>>>> Technology Configuration' >>>>>> class = bridge >>>>>> subclass = HOST-PCI >>>>>> hostb2@pci0:0:24:1: class=0x060000 card=0x00000000 chip=0x12011022 >>>>>> rev=0x00 >>>>>> hdr=0x00 >>>>>> vendor = 'Advanced Micro Devices (AMD)' >>>>>> device = '(Family 10h) Athlon64/Opteron/Sempron Address Map' >>>>>> class = bridge >>>>>> subclass = HOST-PCI >>>>>> hostb3@pci0:0:24:2: class=0x060000 card=0x00000000 chip=0x12021022 >>>>>> rev=0x00 >>>>>> hdr=0x00 >>>>>> vendor = 'Advanced Micro Devices (AMD)' >>>>>> device = '(Family 10h) Athlon64/Opteron/Sempron DRAM >>>>>> Controller' >>>>>> class = bridge >>>>>> subclass = HOST-PCI >>>>>> hostb4@pci0:0:24:3: class=0x060000 card=0x00000000 chip=0x12031022 >>>>>> rev=0x00 >>>>>> hdr=0x00 >>>>>> vendor = 'Advanced Micro Devices (AMD)' >>>>>> device = '(Family 10h) Athlon64/Opteron/Sempron Miscellaneous >>>>>> Control' >>>>>> class = bridge >>>>>> subclass = HOST-PCI >>>>>> hostb5@pci0:0:24:4: class=0x060000 card=0x00000000 chip=0x12041022 >>>>>> rev=0x00 >>>>>> hdr=0x00 >>>>>> vendor = 'Advanced Micro Devices (AMD)' >>>>>> device = '(Family 10h) Athlon64/Opteron/Sempron Link Control' >>>>>> class = bridge >>>>>> subclass = HOST-PCI >>>>>> mpt0@pci0:1:0:0: class=0x010000 card=0xa58015d9 chip=0x00581000 >>>>>> rev=0x08 >>>>>> hdr=0x00 >>>>>> vendor = 'LSI Logic (Was: Symbios Logic, NCR)' >>>>>> device = 'SAS 3000 series, 8-port with 1068E -StorPort' >>>>>> class = mass storage >>>>>> subclass = SCSI >>>>>> mpt1@pci0:2:0:0: class=0x010000 card=0xa58015d9 chip=0x00581000 >>>>>> rev=0x08 >>>>>> hdr=0x00 >>>>>> vendor = 'LSI Logic (Was: Symbios Logic, NCR)' >>>>>> device = 'SAS 3000 series, 8-port with 1068E -StorPort' >>>>>> class = mass storage >>>>>> subclass = SCSI >>>>>> atapci0@pci0:3:0:0: class=0x01018f card=0x612111ab chip=0x612111ab >>>>>> rev=0xb1 >>>>>> hdr=0x00 >>>>>> vendor = 'Marvell Semiconductor (Was: Galileo Technology Ltd)' >>>>>> device = '6121 SATA2 Controller' >>>>>> class = mass storage >>>>>> subclass = ATA >>>>>> mskc0@pci0:4:0:0: class=0x020000 card=0x81f81043 chip=0x436411ab >>>>>> rev=0x12 >>>>>> hdr=0x00 >>>>>> vendor = 'Marvell Semiconductor (Was: Galileo Technology Ltd)' >>>>>> device = 'Yukon PCI-E Gigabit Ethernet Controller (88E8056)' >>>>>> class = network >>>>>> subclass = ethernet >>>>>> atapci2@pci0:5:0:0: class=0x01018f card=0x612111ab chip=0x612111ab >>>>>> rev=0xb2 >>>>>> hdr=0x00 >>>>>> vendor = 'Marvell Semiconductor (Was: Galileo Technology Ltd)' >>>>>> device = '6121 SATA2 Controller' >>>>>> class = mass storage >>>>>> subclass = ATA >>>>>> mpt2@pci0:6:0:0: class=0x010000 card=0x30a01000 chip=0x00581000 >>>>>> rev=0x08 >>>>>> hdr=0x00 >>>>>> vendor = 'LSI Logic (Was: Symbios Logic, NCR)' >>>>>> device = 'SAS 3000 series, 8-port with 1068E -StorPort' >>>>>> class = mass storage >>>>>> subclass = SCSI >>>>>> em0@pci0:7:5:0: class=0x020000 card=0x13768086 chip=0x107c8086 >>>>>> rev=0x05 >>>>>> hdr=0x00 >>>>>> vendor = 'Intel Corporation' >>>>>> device = 'Gigabit Ethernet Controller (Copper) rev 5 (82541PI)' >>>>>> class = network >>>>>> subclass = ethernet >>>>>> vgapci0@pci0:7:6:0: class=0x030000 card=0x00000000 chip=0x88115333 >>>>>> rev=0x44 >>>>>> hdr=0x00 >>>>>> vendor = 'S3 Graphics Co., Ltd' >>>>>> device = '86C732 Trio32, 86C764 Trio64, 86C765 Trio64V+ Rev 01' >>>>>> class = display >>>>>> subclass = VGA >>>>>> none2@pci0:7:8:0: class=0x0c0010 card=0x82941043 chip=0x581111c1 >>>>>> rev=0x70 >>>>>> hdr=0x00 >>>>>> vendor = 'Lucent/Agere Systems (Was: AT&T MicroElectronics)' >>>>>> device = '1394A PCI PHY/Link Open Host Ctrlr I/F (FW322)' >>>>>> class = serial bus >>>>>> subclass = FireWire >>>>>> [josh@foghornleghorn /var/log]$ sudo su - >>>>>> foghornleghorn# pciconf -lvcb >>>>>> hostb0@pci0:0:0:0: class=0x060000 card=0x59561002 chip=0x59561002 >>>>>> rev=0x00 >>>>>> hdr=0x00 >>>>>> vendor = 'ATI Technologies Inc. / Advanced Micro Devices, Inc.' >>>>>> device = 'RD790 GFX Dual Slot' >>>>>> class = bridge >>>>>> subclass = HOST-PCI >>>>>> cap 08[c4] = HT slave >>>>>> cap 08[40] = HT retry mode >>>>>> cap 08[54] = HT unit ID clumping >>>>>> cap 08[9c] = HT unknown d03c >>>>>> pcib1@pci0:0:2:0: class=0x060400 card=0x59561002 chip=0x59781002 >>>>>> rev=0x00 >>>>>> hdr=0x01 >>>>>> vendor = 'ATI Technologies Inc. / Advanced Micro Devices, Inc.' >>>>>> device = 'RD790 PCI to PCI bridge (external gfx0 port A)' >>>>>> class = bridge >>>>>> subclass = PCI-PCI >>>>>> cap 01[50] = powerspec 3 supports D0 D3 current D0 >>>>>> cap 10[58] = PCI-Express 2 root port max data 128(128) link x4(x8) >>>>>> cap 05[a0] = MSI supports 1 message >>>>>> cap 0d[b0] = PCI Bridge card=0x59561002 >>>>>> cap 08[b8] = HT MSI fixed address window enabled at 0xfee00000 >>>>>> ecap 000b[100] = unknown 1 >>>>>> ecap 0002[110] = VC 1 max VC0 >>>>>> pcib2@pci0:0:3:0: class=0x060400 card=0x59561002 chip=0x59791002 >>>>>> rev=0x00 >>>>>> hdr=0x01 >>>>>> vendor = 'ATI Technologies Inc. / Advanced Micro Devices, Inc.' >>>>>> device = 'RD790 PCI to PCI bridge (external gfx0 port B)' >>>>>> class = bridge >>>>>> subclass = PCI-PCI >>>>>> cap 01[50] = powerspec 3 supports D0 D3 current D0 >>>>>> cap 10[58] = PCI-Express 2 root port max data 128(128) link x4(x8) >>>>>> cap 05[a0] = MSI supports 1 message >>>>>> cap 0d[b0] = PCI Bridge card=0x59561002 >>>>>> cap 08[b8] = HT MSI fixed address window enabled at 0xfee00000 >>>>>> ecap 000b[100] = unknown 1 >>>>>> ecap 0002[110] = VC 1 max VC0 >>>>>> pcib3@pci0:0:4:0: class=0x060400 card=0x59561002 chip=0x597a1002 >>>>>> rev=0x00 >>>>>> hdr=0x01 >>>>>> vendor = 'ATI Technologies Inc. / Advanced Micro Devices, Inc.' >>>>>> device = 'RD790 PCI to PCI bridge (PCIe gpp port A)' >>>>>> class = bridge >>>>>> subclass = PCI-PCI >>>>>> cap 01[50] = powerspec 3 supports D0 D3 current D0 >>>>>> cap 10[58] = PCI-Express 2 root port max data 128(128) link x1(x2) >>>>>> cap 05[a0] = MSI supports 1 message >>>>>> cap 0d[b0] = PCI Bridge card=0x59561002 >>>>>> cap 08[b8] = HT MSI fixed address window enabled at 0xfee00000 >>>>>> ecap 000b[100] = unknown 1 >>>>>> ecap 0002[110] = VC 1 max VC0 >>>>>> pcib4@pci0:0:6:0: class=0x060400 card=0x59561002 chip=0x597c1002 >>>>>> rev=0x00 >>>>>> hdr=0x01 >>>>>> vendor = 'ATI Technologies Inc. / Advanced Micro Devices, Inc.' >>>>>> device = 'RD790 PCI to PCI bridge (PCIe gpp port C)' >>>>>> class = bridge >>>>>> subclass = PCI-PCI >>>>>> cap 01[50] = powerspec 3 supports D0 D3 current D0 >>>>>> cap 10[58] = PCI-Express 2 root port max data 128(128) link x1(x1) >>>>>> cap 05[a0] = MSI supports 1 message >>>>>> cap 0d[b0] = PCI Bridge card=0x59561002 >>>>>> cap 08[b8] = HT MSI fixed address window enabled at 0xfee00000 >>>>>> ecap 000b[100] = unknown 1 >>>>>> ecap 0002[110] = VC 1 max VC0 >>>>>> pcib5@pci0:0:7:0: class=0x060400 card=0x59561002 chip=0x597d1002 >>>>>> rev=0x00 >>>>>> hdr=0x01 >>>>>> vendor = 'ATI Technologies Inc. / Advanced Micro Devices, Inc.' >>>>>> device = 'RD790 PCI to PCI bridge (PCIe gpp port D)' >>>>>> class = bridge >>>>>> subclass = PCI-PCI >>>>>> cap 01[50] = powerspec 3 supports D0 D3 current D0 >>>>>> cap 10[58] = PCI-Express 2 root port max data 128(128) link x1(x1) >>>>>> cap 05[a0] = MSI supports 1 message >>>>>> cap 0d[b0] = PCI Bridge card=0x59561002 >>>>>> cap 08[b8] = HT MSI fixed address window enabled at 0xfee00000 >>>>>> ecap 000b[100] = unknown 1 >>>>>> ecap 0002[110] = VC 1 max VC0 >>>>>> pcib6@pci0:0:11:0: class=0x060400 card=0x59561002 chip=0x59801002 >>>>>> rev=0x00 >>>>>> hdr=0x01 >>>>>> vendor = 'ATI Technologies Inc. / Advanced Micro Devices, Inc.' >>>>>> device = 'RD790 PCI to PCI bridge (external gfx1 port A)' >>>>>> class = bridge >>>>>> subclass = PCI-PCI >>>>>> cap 01[50] = powerspec 3 supports D0 D3 current D0 >>>>>> cap 10[58] = PCI-Express 2 root port max data 128(128) link x4(x8) >>>>>> cap 05[a0] = MSI supports 1 message >>>>>> cap 0d[b0] = PCI Bridge card=0x59561002 >>>>>> cap 08[b8] = HT MSI fixed address window enabled at 0xfee00000 >>>>>> ecap 000b[100] = unknown 1 >>>>>> ecap 0002[110] = VC 1 max VC0 >>>>>> atapci4@pci0:0:18:0: class=0x01018f card=0x81ef1043 chip=0x43801002 >>>>>> rev=0x00 >>>>>> hdr=0x00 >>>>>> vendor = 'ATI Technologies Inc. / Advanced Micro Devices, Inc.' >>>>>> device = 'IXP SB600 Serial ATA Controller' >>>>>> class = mass storage >>>>>> subclass = ATA >>>>>> bar [10] = type I/O Port, range 32, base 0x5000, size 8, enabled >>>>>> bar [14] = type I/O Port, range 32, base 0x4000, size 4, enabled >>>>>> bar [18] = type I/O Port, range 32, base 0x3000, size 8, enabled >>>>>> bar [1c] = type I/O Port, range 32, base 0x2000, size 4, enabled >>>>>> bar [20] = type I/O Port, range 32, base 0x1000, size 16, enabled >>>>>> bar [24] = type Memory, range 32, base 0xf71ff800, size 1024, >>>>>> enabled >>>>>> cap 01[60] = powerspec 2 supports D0 D3 current D0 >>>>>> ohci0@pci0:0:19:0: class=0x0c0310 card=0x82881043 chip=0x43871002 >>>>>> rev=0x00 >>>>>> hdr=0x00 >>>>>> vendor = 'ATI Technologies Inc. / Advanced Micro Devices, Inc.' >>>>>> device = 'IXP SB600 USB Controller (OHCI0)' >>>>>> class = serial bus >>>>>> subclass = USB >>>>>> bar [10] = type Memory, range 32, base 0xf71fe000, size 4096, >>>>>> enabled >>>>>> ohci1@pci0:0:19:1: class=0x0c0310 card=0x82881043 chip=0x43881002 >>>>>> rev=0x00 >>>>>> hdr=0x00 >>>>>> vendor = 'ATI Technologies Inc. / Advanced Micro Devices, Inc.' >>>>>> device = 'IXP SB600 USB Controller (OHCI1)' >>>>>> class = serial bus >>>>>> subclass = USB >>>>>> bar [10] = type Memory, range 32, base 0xf71fd000, size 4096, >>>>>> enabled >>>>>> ohci2@pci0:0:19:2: class=0x0c0310 card=0x82881043 chip=0x43891002 >>>>>> rev=0x00 >>>>>> hdr=0x00 >>>>>> vendor = 'ATI Technologies Inc. / Advanced Micro Devices, Inc.' >>>>>> device = 'IXP SB600 USB Controller (OHCI2)' >>>>>> class = serial bus >>>>>> subclass = USB >>>>>> bar [10] = type Memory, range 32, base 0xf71fc000, size 4096, >>>>>> enabled >>>>>> ohci3@pci0:0:19:3: class=0x0c0310 card=0x82881043 chip=0x438a1002 >>>>>> rev=0x00 >>>>>> hdr=0x00 >>>>>> vendor = 'ATI Technologies Inc. / Advanced Micro Devices, Inc.' >>>>>> device = 'IXP SB600 USB Controller (OHCI3)' >>>>>> class = serial bus >>>>>> subclass = USB >>>>>> bar [10] = type Memory, range 32, base 0xf71fb000, size 4096, >>>>>> enabled >>>>>> ohci4@pci0:0:19:4: class=0x0c0310 card=0x82881043 chip=0x438b1002 >>>>>> rev=0x00 >>>>>> hdr=0x00 >>>>>> vendor = 'ATI Technologies Inc. / Advanced Micro Devices, Inc.' >>>>>> device = 'IXP SB600 USB Controller (OHCI4)' >>>>>> class = serial bus >>>>>> subclass = USB >>>>>> bar [10] = type Memory, range 32, base 0xf71fa000, size 4096, >>>>>> enabled >>>>>> ehci0@pci0:0:19:5: class=0x0c0320 card=0x82881043 chip=0x43861002 >>>>>> rev=0x00 >>>>>> hdr=0x00 >>>>>> vendor = 'ATI Technologies Inc. / Advanced Micro Devices, Inc.' >>>>>> device = 'IXP SB600 USB Controller (EHCI)' >>>>>> class = serial bus >>>>>> subclass = USB >>>>>> bar [10] = type Memory, range 32, base 0xf71ff000, size 256, >>>>>> enabled >>>>>> cap 01[c0] = powerspec 2 supports D0 D1 D2 D3 current D0 >>>>>> cap 05[d0] = MSI supports 1 message >>>>>> cap 0a[e4] = EHCI Debug Port at offset 0xe0 in map 0x14 >>>>>> none0@pci0:0:20:0: class=0x0c0500 card=0x82881043 chip=0x43851002 >>>>>> rev=0x14 >>>>>> hdr=0x00 >>>>>> vendor = 'ATI Technologies Inc. / Advanced Micro Devices, Inc.' >>>>>> device = 'ATI SMBus (ATI RD600/RS600)' >>>>>> class = serial bus >>>>>> subclass = SMBus >>>>>> bar [10] = type I/O Port, range 32, base 0xb00, size 16, enabled >>>>>> cap 08[b0] = HT MSI fixed address window disabled at 0xfee00000 >>>>>> atapci5@pci0:0:20:1: class=0x01018a card=0x82881043 chip=0x438c1002 >>>>>> rev=0x00 >>>>>> hdr=0x00 >>>>>> vendor = 'ATI Technologies Inc. / Advanced Micro Devices, Inc.' >>>>>> device = 'ATI RD600/RS600 IDE Controller (RD600/RS600)' >>>>>> class = mass storage >>>>>> subclass = ATA >>>>>> bar [10] = type I/O Port, range 32, base 0x1f0, size 8, enabled >>>>>> bar [14] = type I/O Port, range 32, base 0x3f4, size 1, enabled >>>>>> bar [18] = type I/O Port, range 32, base 0x170, size 8, enabled >>>>>> bar [1c] = type I/O Port, range 32, base 0x374, size 1, enabled >>>>>> bar [20] = type I/O Port, range 32, base 0xff00, size 16, enabled >>>>>> none1@pci0:0:20:2: class=0x040300 card=0x82881043 chip=0x43831002 >>>>>> rev=0x00 >>>>>> hdr=0x00 >>>>>> vendor = 'ATI Technologies Inc. / Advanced Micro Devices, Inc.' >>>>>> device = 'IXP SB600 High Definition Audio Controller' >>>>>> class = multimedia >>>>>> subclass = HDA >>>>>> bar [10] = type Memory, range 64, base 0xf71f4000, size 16384, >>>>>> enabled >>>>>> cap 01[50] = powerspec 2 supports D0 D3 current D0 >>>>>> isab0@pci0:0:20:3: class=0x060100 card=0x82881043 chip=0x438d1002 >>>>>> rev=0x00 >>>>>> hdr=0x00 >>>>>> vendor = 'ATI Technologies Inc. / Advanced Micro Devices, Inc.' >>>>>> device = 'IXP SB600 PCI to LPC Bridge' >>>>>> class = bridge >>>>>> subclass = PCI-ISA >>>>>> pcib7@pci0:0:20:4: class=0x060401 card=0x00000000 chip=0x43841002 >>>>>> rev=0x00 >>>>>> hdr=0x01 >>>>>> vendor = 'ATI Technologies Inc. / Advanced Micro Devices, Inc.' >>>>>> device = 'IXP SB600 PCI to PCI Bridge' >>>>>> class = bridge >>>>>> subclass = PCI-PCI >>>>>> hostb1@pci0:0:24:0: class=0x060000 card=0x00000000 chip=0x12001022 >>>>>> rev=0x00 >>>>>> hdr=0x00 >>>>>> vendor = 'Advanced Micro Devices (AMD)' >>>>>> device = '(Family 10h) Athlon64/Opteron/Sempron HyperTransport >>>>>> Technology Configuration' >>>>>> class = bridge >>>>>> subclass = HOST-PCI >>>>>> cap 08[80] = HT host >>>>>> hostb2@pci0:0:24:1: class=0x060000 card=0x00000000 chip=0x12011022 >>>>>> rev=0x00 >>>>>> hdr=0x00 >>>>>> vendor = 'Advanced Micro Devices (AMD)' >>>>>> device = '(Family 10h) Athlon64/Opteron/Sempron Address Map' >>>>>> class = bridge >>>>>> subclass = HOST-PCI >>>>>> hostb3@pci0:0:24:2: class=0x060000 card=0x00000000 chip=0x12021022 >>>>>> rev=0x00 >>>>>> hdr=0x00 >>>>>> vendor = 'Advanced Micro Devices (AMD)' >>>>>> device = '(Family 10h) Athlon64/Opteron/Sempron DRAM >>>>>> Controller' >>>>>> class = bridge >>>>>> subclass = HOST-PCI >>>>>> hostb4@pci0:0:24:3: class=0x060000 card=0x00000000 chip=0x12031022 >>>>>> rev=0x00 >>>>>> hdr=0x00 >>>>>> vendor = 'Advanced Micro Devices (AMD)' >>>>>> device = '(Family 10h) Athlon64/Opteron/Sempron Miscellaneous >>>>>> Control' >>>>>> class = bridge >>>>>> subclass = HOST-PCI >>>>>> cap 0f[f0] = unknown >>>>>> hostb5@pci0:0:24:4: class=0x060000 card=0x00000000 chip=0x12041022 >>>>>> rev=0x00 >>>>>> hdr=0x00 >>>>>> vendor = 'Advanced Micro Devices (AMD)' >>>>>> device = '(Family 10h) Athlon64/Opteron/Sempron Link Control' >>>>>> class = bridge >>>>>> subclass = HOST-PCI >>>>>> mpt0@pci0:1:0:0: class=0x010000 card=0xa58015d9 chip=0x00581000 >>>>>> rev=0x08 >>>>>> hdr=0x00 >>>>>> vendor = 'LSI Logic (Was: Symbios Logic, NCR)' >>>>>> device = 'SAS 3000 series, 8-port with 1068E -StorPort' >>>>>> class = mass storage >>>>>> subclass = SCSI >>>>>> bar [10] = type I/O Port, range 32, base 0x6000, size 256, >>>>>> disabled >>>>>> bar [14] = type Memory, range 64, base 0xf75fc000, size 16384, >>>>>> enabled >>>>>> bar [1c] = type Memory, range 64, base 0xf75e0000, size 65536, >>>>>> enabled >>>>>> cap 01[50] = powerspec 2 supports D0 D1 D2 D3 current D0 >>>>>> cap 10[68] = PCI-Express 1 endpoint max data 128(4096) link x4(x8) >>>>>> cap 05[98] = MSI supports 1 message, 64 bit >>>>>> cap 11[b0] = MSI-X supports 1 message in map 0x14 >>>>>> ecap 0001[100] = AER 1 1 fatal 1 non-fatal 0 corrected >>>>>> mpt1@pci0:2:0:0: class=0x010000 card=0xa58015d9 chip=0x00581000 >>>>>> rev=0x08 >>>>>> hdr=0x00 >>>>>> vendor = 'LSI Logic (Was: Symbios Logic, NCR)' >>>>>> device = 'SAS 3000 series, 8-port with 1068E -StorPort' >>>>>> class = mass storage >>>>>> subclass = SCSI >>>>>> bar [10] = type I/O Port, range 32, base 0x7000, size 256, >>>>>> disabled >>>>>> bar [14] = type Memory, range 64, base 0xf78fc000, size 16384, >>>>>> enabled >>>>>> bar [1c] = type Memory, range 64, base 0xf78e0000, size 65536, >>>>>> enabled >>>>>> cap 01[50] = powerspec 2 supports D0 D1 D2 D3 current D0 >>>>>> cap 10[68] = PCI-Express 1 endpoint max data 128(4096) link x4(x8) >>>>>> cap 05[98] = MSI supports 1 message, 64 bit >>>>>> cap 11[b0] = MSI-X supports 1 message in map 0x14 >>>>>> ecap 0001[100] = AER 1 1 fatal 1 non-fatal 0 corrected >>>>>> atapci0@pci0:3:0:0: class=0x01018f card=0x612111ab chip=0x612111ab >>>>>> rev=0xb1 >>>>>> hdr=0x00 >>>>>> vendor = 'Marvell Semiconductor (Was: Galileo Technology Ltd)' >>>>>> device = '6121 SATA2 Controller' >>>>>> class = mass storage >>>>>> subclass = ATA >>>>>> bar [10] = type I/O Port, range 32, base 0x9800, size 8, enabled >>>>>> bar [14] = type I/O Port, range 32, base 0x9400, size 4, enabled >>>>>> bar [18] = type I/O Port, range 32, base 0x9000, size 8, enabled >>>>>> bar [1c] = type I/O Port, range 32, base 0x8800, size 4, enabled >>>>>> bar [20] = type I/O Port, range 32, base 0x8400, size 16, enabled >>>>>> bar [24] = type Memory, range 32, base 0xf79ffc00, size 1024, >>>>>> enabled >>>>>> cap 01[48] = powerspec 2 supports D0 D1 D3 current D0 >>>>>> cap 05[50] = MSI supports 1 message >>>>>> cap 10[e0] = PCI-Express 1 legacy endpoint max data 128(128) link >>>>>> x1(x1) >>>>>> ecap 0001[100] = AER 1 0 fatal 0 non-fatal 2 corrected >>>>>> mskc0@pci0:4:0:0: class=0x020000 card=0x81f81043 chip=0x436411ab >>>>>> rev=0x12 >>>>>> hdr=0x00 >>>>>> vendor = 'Marvell Semiconductor (Was: Galileo Technology Ltd)' >>>>>> device = 'Yukon PCI-E Gigabit Ethernet Controller (88E8056)' >>>>>> class = network >>>>>> subclass = ethernet >>>>>> bar [10] = type Memory, range 64, base 0xf7afc000, size 16384, >>>>>> enabled >>>>>> bar [18] = type I/O Port, range 32, base 0xa800, size 256, >>>>>> enabled >>>>>> cap 01[48] = powerspec 3 supports D0 D1 D2 D3 current D0 >>>>>> cap 03[50] = VPD >>>>>> cap 05[5c] = MSI supports 1 message, 64 bit enabled with 1 message >>>>>> cap 10[e0] = PCI-Express 1 legacy endpoint max data 128(128) link >>>>>> x1(x1) >>>>>> ecap 0001[100] = AER 1 0 fatal 0 non-fatal 1 corrected >>>>>> atapci2@pci0:5:0:0: class=0x01018f card=0x612111ab chip=0x612111ab >>>>>> rev=0xb2 >>>>>> hdr=0x00 >>>>>> vendor = 'Marvell Semiconductor (Was: Galileo Technology Ltd)' >>>>>> device = '6121 SATA2 Controller' >>>>>> class = mass storage >>>>>> subclass = ATA >>>>>> bar [10] = type I/O Port, range 32, base 0xc800, size 8, enabled >>>>>> bar [14] = type I/O Port, range 32, base 0xc400, size 4, enabled >>>>>> bar [18] = type I/O Port, range 32, base 0xc000, size 8, enabled >>>>>> bar [1c] = type I/O Port, range 32, base 0xb800, size 4, enabled >>>>>> bar [20] = type I/O Port, range 32, base 0xb400, size 16, enabled >>>>>> bar [24] = type Memory, range 32, base 0xf7bffc00, size 1024, >>>>>> enabled >>>>>> cap 01[48] = powerspec 2 supports D0 D1 D3 current D0 >>>>>> cap 05[50] = MSI supports 1 message >>>>>> cap 10[e0] = PCI-Express 1 legacy endpoint max data 128(128) link >>>>>> x1(x1) >>>>>> ecap 0001[100] = AER 1 0 fatal 0 non-fatal 1 corrected >>>>>> mpt2@pci0:6:0:0: class=0x010000 card=0x30a01000 chip=0x00581000 >>>>>> rev=0x08 >>>>>> hdr=0x00 >>>>>> vendor = 'LSI Logic (Was: Symbios Logic, NCR)' >>>>>> device = 'SAS 3000 series, 8-port with 1068E -StorPort' >>>>>> class = mass storage >>>>>> subclass = SCSI >>>>>> bar [10] = type I/O Port, range 32, base 0xd000, size 256, >>>>>> disabled >>>>>> bar [14] = type Memory, range 64, base 0xf7ffc000, size 16384, >>>>>> enabled >>>>>> bar [1c] = type Memory, range 64, base 0xf7fe0000, size 65536, >>>>>> enabled >>>>>> cap 01[50] = powerspec 2 supports D0 D1 D2 D3 current D0 >>>>>> cap 10[68] = PCI-Express 1 endpoint max data 128(4096) link x4(x8) >>>>>> cap 05[98] = MSI supports 1 message, 64 bit >>>>>> cap 11[b0] = MSI-X supports 1 message in map 0x14 >>>>>> ecap 0001[100] = AER 1 1 fatal 1 non-fatal 0 corrected >>>>>> em0@pci0:7:5:0: class=0x020000 card=0x13768086 chip=0x107c8086 >>>>>> rev=0x05 >>>>>> hdr=0x00 >>>>>> vendor = 'Intel Corporation' >>>>>> device = 'Gigabit Ethernet Controller (Copper) rev 5 (82541PI)' >>>>>> class = network >>>>>> subclass = ethernet >>>>>> bar [10] = type Memory, range 32, base 0xfebe0000, size 131072, >>>>>> enabled >>>>>> bar [14] = type Memory, range 32, base 0xfebc0000, size 131072, >>>>>> enabled >>>>>> bar [18] = type I/O Port, range 32, base 0xe800, size 64, enabled >>>>>> cap 01[dc] = powerspec 2 supports D0 D3 current D0 >>>>>> cap 07[e4] = PCI-X supports 2048 burst read, 1 split transaction >>>>>> vgapci0@pci0:7:6:0: class=0x030000 card=0x00000000 chip=0x88115333 >>>>>> rev=0x44 >>>>>> hdr=0x00 >>>>>> vendor = 'S3 Graphics Co., Ltd' >>>>>> device = '86C732 Trio32, 86C764 Trio64, 86C765 Trio64V+ Rev 01' >>>>>> class = display >>>>>> subclass = VGA >>>>>> bar [10] = type Memory, range 32, base 0xf8000000, size 67108864, >>>>>> enabled >>>>>> none2@pci0:7:8:0: class=0x0c0010 card=0x82941043 chip=0x581111c1 >>>>>> rev=0x70 >>>>>> hdr=0x00 >>>>>> vendor = 'Lucent/Agere Systems (Was: AT&T MicroElectronics)' >>>>>> device = '1394A PCI PHY/Link Open Host Ctrlr I/F (FW322)' >>>>>> class = serial bus >>>>>> subclass = FireWire >>>>>> bar [10] = type Memory, range 32, base 0xfeb8f000, size 4096, >>>>>> enabled >>>>>> cap 01[44] = powerspec 2 supports D0 D1 D2 D3 current D0 >>>>>> >>>>>> >>>>>> >>>>>> > # vmstat -i >>>>>> > >>>>>> >>>>>> interrupt total rate >>>>>> irq9: acpi0 1 0 >>>>>> irq16: atapci0+ 2 0 >>>>>> irq17: ohci1 ohci3 3 0 >>>>>> irq18: mpt0 ohci2+ 7066718 31 >>>>>> irq19: mpt1 atapci* 7798877 34 >>>>>> irq20: em0 11715792 51 >>>>>> irq22: atapci4 628883 2 >>>>>> cpu0: timer 455853831 1999 >>>>>> irq256: mskc0 97098730 425 >>>>>> cpu1: timer 455845190 1999 >>>>>> Total 1036008027 4544 >>>>>> >>>>>> >>>>>> >>>>>> > # sysctl -a | grep msi >>>>>> > >>>>>> >>>>>> hw.pci.honor_msi_blacklist: 1 >>>>>> hw.pci.enable_msix: 1 >>>>>> hw.pci.enable_msi: 1 >>>>>> >>>>>> >>>>>> >>>>>> > # dmesg >>>>>> > >>>>>> >>>>>> Copyright (c) 1992-2011 The FreeBSD Project. >>>>>> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, >>>>>> 1994 >>>>>> The Regents of the University of California. All rights reserved. >>>>>> FreeBSD is a registered trademark of The FreeBSD Foundation. >>>>>> FreeBSD 8.2-STABLE #17: Mon Jun 6 19:40:19 EDT 2011 >>>>>> root@foghornleghorn.res.openband.net: >>>>>> /usr/obj/usr/src/sys/FOGHORNLEGHORN >>>>>> amd64 >>>>>> Timecounter "i8254" frequency 1193182 Hz quality 0 >>>>>> CPU: AMD Phenom(tm) II X2 555 Processor (3209.77-MHz K8-class CPU) >>>>>> Origin = "AuthenticAMD" Id = 0x100f43 Family = 10 Model = 4 >>>>>> Stepping = >>>>>> 3 >>>>>> >>>>>> >>>>>> Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT> >>>>>> Features2=0x802009<SSE3,MON,CX16,POPCNT> >>>>>> AMD >>>>>> >>>>>> Features=0xee500800<SYSCALL,NX,MMX+,FFXSR,Page1GB,RDTSCP,LM,3DNow!+,3DNow!> >>>>>> AMD >>>>>> >>>>>> Features2=0x37ff<LAHF,CMP,SVM,ExtAPIC,CR8,ABM,SSE4A,MAS,Prefetch,OSVW,IBS,SKINIT,WDT> >>>>>> TSC: P-state invariant >>>>>> real memory = 8589934592 (8192 MB) >>>>>> avail memory = 8257736704 (7875 MB) >>>>>> ACPI APIC Table: <092310 OEMAPIC > >>>>>> FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs >>>>>> FreeBSD/SMP: 1 package(s) x 2 core(s) >>>>>> cpu0 (BSP): APIC ID: 0 >>>>>> cpu1 (AP): APIC ID: 1 >>>>>> ioapic0 <Version 2.1> irqs 0-23 on motherboard >>>>>> acpi0: <092310 OEMRSDT> on motherboard >>>>>> acpi0: [ITHREAD] >>>>>> acpi0: Power Button (fixed) >>>>>> acpi0: reservation of fee00000, 1000 (3) failed >>>>>> acpi0: reservation of ffb80000, 80000 (3) failed >>>>>> acpi0: reservation of fff00000, 100000 (3) failed >>>>>> acpi0: reservation of 0, a0000 (3) failed >>>>>> acpi0: reservation of 100000, dff00000 (3) failed >>>>>> Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 >>>>>> acpi_timer0: <32-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0 >>>>>> cpu0: <ACPI CPU> on acpi0 >>>>>> cpu1: <ACPI CPU> on acpi0 >>>>>> acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff >>>>>> on >>>>>> acpi0 >>>>>> Timecounter "HPET" frequency 14318180 Hz quality 900 >>>>>> pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 >>>>>> pci0: <ACPI PCI bus> on pcib0 >>>>>> pcib1: <ACPI PCI-PCI bridge> irq 18 at device 2.0 on pci0 >>>>>> pci1: <ACPI PCI bus> on pcib1 >>>>>> mpt0: <LSILogic SAS/SATA Adapter> port 0x6000-0x60ff mem >>>>>> 0xf75fc000-0xf75fffff,0xf75e0000-0xf75effff irq 18 at device 0.0 on >>>>>> pci1 >>>>>> mpt0: [ITHREAD] >>>>>> mpt0: MPI Version=1.5.20.0 >>>>>> pcib2: <ACPI PCI-PCI bridge> irq 19 at device 3.0 on pci0 >>>>>> pci2: <ACPI PCI bus> on pcib2 >>>>>> mpt1: <LSILogic SAS/SATA Adapter> port 0x7000-0x70ff mem >>>>>> 0xf78fc000-0xf78fffff,0xf78e0000-0xf78effff irq 19 at device 0.0 on >>>>>> pci2 >>>>>> mpt1: [ITHREAD] >>>>>> mpt1: MPI Version=1.5.20.0 >>>>>> pcib3: <ACPI PCI-PCI bridge> irq 16 at device 4.0 on pci0 >>>>>> pci3: <ACPI PCI bus> on pcib3 >>>>>> atapci0: <Marvell 88SX6121 UDMA133 controller> port >>>>>> 0x9800-0x9807,0x9400-0x9403,0x9000-0x9007,0x8800-0x8803,0x8400-0x840f >>>>>> mem >>>>>> 0xf79ffc00-0xf79fffff irq 16 at device 0.0 on pci3 >>>>>> atapci0: [ITHREAD] >>>>>> atapci1: <AHCI SATA controller> on atapci0 >>>>>> atapci1: [ITHREAD] >>>>>> atapci1: AHCI v1.00 controller with 3 3Gbps ports, PM supported >>>>>> ata2: <ATA channel 0> on atapci1 >>>>>> ata2: [ITHREAD] >>>>>> ata3: <ATA channel 1> on atapci1 >>>>>> ata3: [ITHREAD] >>>>>> ata4: <ATA channel 0> on atapci0 >>>>>> ata4: [ITHREAD] >>>>>> pcib4: <ACPI PCI-PCI bridge> irq 18 at device 6.0 on pci0 >>>>>> pci4: <ACPI PCI bus> on pcib4 >>>>>> mskc0: <Marvell Yukon 88E8056 Gigabit Ethernet> port 0xa800-0xa8ff mem >>>>>> 0xf7afc000-0xf7afffff irq 18 at device 0.0 on pci4 >>>>>> msk0: <Marvell Technology Group Ltd. Yukon EC Ultra Id 0xb4 Rev 0x03> >>>>>> on >>>>>> mskc0 >>>>>> msk0: Ethernet address: 00:1f:c6:e9:f8:7c >>>>>> miibus0: <MII bus> on msk0 >>>>>> e1000phy0: <Marvell 88E1149 Gigabit PHY> PHY 0 on miibus0 >>>>>> e1000phy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, >>>>>> 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow >>>>>> mskc0: [ITHREAD] >>>>>> pcib5: <ACPI PCI-PCI bridge> irq 19 at device 7.0 on pci0 >>>>>> pci5: <ACPI PCI bus> on pcib5 >>>>>> atapci2: <Marvell 88SX6121 UDMA133 controller> port >>>>>> 0xc800-0xc807,0xc400-0xc403,0xc000-0xc007,0xb800-0xb803,0xb400-0xb40f >>>>>> mem >>>>>> 0xf7bffc00-0xf7bfffff irq 19 at device 0.0 on pci5 >>>>>> atapci2: [ITHREAD] >>>>>> atapci3: <AHCI SATA controller> on atapci2 >>>>>> atapci3: [ITHREAD] >>>>>> atapci3: AHCI v1.00 controller with 3 3Gbps ports, PM supported >>>>>> ata5: <ATA channel 0> on atapci3 >>>>>> ata5: [ITHREAD] >>>>>> ata6: <ATA channel 1> on atapci3 >>>>>> ata6: [ITHREAD] >>>>>> ata7: <ATA channel 0> on atapci2 >>>>>> ata7: [ITHREAD] >>>>>> pcib6: <ACPI PCI-PCI bridge> irq 19 at device 11.0 on pci0 >>>>>> pci6: <ACPI PCI bus> on pcib6 >>>>>> mpt2: <LSILogic SAS/SATA Adapter> port 0xd000-0xd0ff mem >>>>>> 0xf7ffc000-0xf7ffffff,0xf7fe0000-0xf7feffff irq 19 at device 0.0 on >>>>>> pci6 >>>>>> mpt2: [ITHREAD] >>>>>> mpt2: MPI Version=1.5.19.0 >>>>>> atapci4: <ATI IXP600 SATA300 controller> port >>>>>> 0x5000-0x5007,0x4000-0x4003,0x3000-0x3007,0x2000-0x2003,0x1000-0x100f >>>>>> mem >>>>>> 0xf71ff800-0xf71ffbff irq 22 at device 18.0 on pci0 >>>>>> atapci4: [ITHREAD] >>>>>> atapci4: AHCI v1.10 controller with 4 3Gbps ports, PM supported >>>>>> ata8: <ATA channel 0> on atapci4 >>>>>> ata8: port is not ready (timeout 0ms) tfd = 000001d0 >>>>>> ata8: software reset clear timeout >>>>>> ata8: [ITHREAD] >>>>>> ata9: <ATA channel 1> on atapci4 >>>>>> ata9: [ITHREAD] >>>>>> ata10: <ATA channel 2> on atapci4 >>>>>> ata10: [ITHREAD] >>>>>> ata11: <ATA channel 3> on atapci4 >>>>>> ata11: [ITHREAD] >>>>>> ohci0: <OHCI (generic) USB controller> mem 0xf71fe000-0xf71fefff irq >>>>>> 16 at >>>>>> device 19.0 on pci0 >>>>>> ohci0: [ITHREAD] >>>>>> usbus0: <OHCI (generic) USB controller> on ohci0 >>>>>> ohci1: <OHCI (generic) USB controller> mem 0xf71fd000-0xf71fdfff irq >>>>>> 17 at >>>>>> device 19.1 on pci0 >>>>>> ohci1: [ITHREAD] >>>>>> usbus1: <OHCI (generic) USB controller> on ohci1 >>>>>> ohci2: <OHCI (generic) USB controller> mem 0xf71fc000-0xf71fcfff irq >>>>>> 18 at >>>>>> device 19.2 on pci0 >>>>>> ohci2: [ITHREAD] >>>>>> usbus2: <OHCI (generic) USB controller> on ohci2 >>>>>> ohci3: <OHCI (generic) USB controller> mem 0xf71fb000-0xf71fbfff irq >>>>>> 17 at >>>>>> device 19.3 on pci0 >>>>>> ohci3: [ITHREAD] >>>>>> usbus3: <OHCI (generic) USB controller> on ohci3 >>>>>> ohci4: <OHCI (generic) USB controller> mem 0xf71fa000-0xf71fafff irq >>>>>> 18 at >>>>>> device 19.4 on pci0 >>>>>> ohci4: [ITHREAD] >>>>>> usbus4: <OHCI (generic) USB controller> on ohci4 >>>>>> ehci0: <EHCI (generic) USB 2.0 controller> mem 0xf71ff000-0xf71ff0ff >>>>>> irq 19 >>>>>> at device 19.5 on pci0 >>>>>> ehci0: [ITHREAD] >>>>>> ehci0: AMD SB600/700 quirk applied >>>>>> usbus5: EHCI version 1.0 >>>>>> usbus5: <EHCI (generic) USB 2.0 controller> on ehci0 >>>>>> pci0: <serial bus, SMBus> at device 20.0 (no driver attached) >>>>>> atapci5: <ATI IXP600 UDMA133 controller> port >>>>>> 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xff00-0xff0f at device 20.1 on >>>>>> pci0 >>>>>> ata0: <ATA channel 0> on atapci5 >>>>>> ata0: [ITHREAD] >>>>>> pci0: <multimedia, HDA> at device 20.2 (no driver attached) >>>>>> isab0: <PCI-ISA bridge> at device 20.3 on pci0 >>>>>> isa0: <ISA bus> on isab0 >>>>>> pcib7: <ACPI PCI-PCI bridge> at device 20.4 on pci0 >>>>>> pci7: <ACPI PCI bus> on pcib7 >>>>>> em0: <Intel(R) PRO/1000 Legacy Network Connection 1.0.3> port >>>>>> 0xe800-0xe83f >>>>>> mem 0xfebe0000-0xfebfffff,0xfebc0000-0xfebdffff irq 20 at device 5.0 >>>>>> on pci7 >>>>>> em0: [FILTER] >>>>>> em0: Ethernet address: 00:1b:21:4e:e5:2e >>>>>> vgapci0: <VGA-compatible display> mem 0xf8000000-0xfbffffff at device >>>>>> 6.0 on >>>>>> pci7 >>>>>> pci7: <serial bus, FireWire> at device 8.0 (no driver attached) >>>>>> acpi_button0: <Power Button> on acpi0 >>>>>> atrtc0: <AT realtime clock> port 0x70-0x71 irq 8 on acpi0 >>>>>> acpi_hpet1: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff >>>>>> on >>>>>> acpi0 >>>>>> device_attach: acpi_hpet1 attach returned 12 >>>>>> uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on >>>>>> acpi0 >>>>>> uart0: [FILTER] >>>>>> orm0: <ISA Option ROMs> at iomem >>>>>> 0xc0000-0xc7fff,0xc8000-0xc87ff,0xc8800-0xc97ff on isa0 >>>>>> sc0: <System console> at flags 0x100 on isa0 >>>>>> sc0: VGA <16 virtual consoles, flags=0x300> >>>>>> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on >>>>>> isa0 >>>>>> acpi_throttle0: <ACPI CPU Throttling> on cpu0 >>>>>> acpi_throttle0: CLK_VAL field overlaps THT_EN bit >>>>>> device_attach: acpi_throttle0 attach returned 6 >>>>>> hwpstate0: <Cool`n'Quiet 2.0> on cpu0 >>>>>> Timecounters tick every 1.000 msec >>>>>> usbus0: 12Mbps Full Speed USB v1.0 >>>>>> usbus1: 12Mbps Full Speed USB v1.0 >>>>>> usbus2: 12Mbps Full Speed USB v1.0 >>>>>> usbus3: 12Mbps Full Speed USB v1.0 >>>>>> usbus4: 12Mbps Full Speed USB v1.0 >>>>>> usbus5: 480Mbps High Speed USB v2.0 >>>>>> ugen0.1: <ATI> at usbus0 >>>>>> uhub0: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0 >>>>>> ugen1.1: <ATI> at usbus1 >>>>>> uhub1: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1 >>>>>> ugen2.1: <ATI> at usbus2 >>>>>> uhub2: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2 >>>>>> ugen3.1: <ATI> at usbus3 >>>>>> uhub3: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3 >>>>>> ugen4.1: <ATI> at usbus4 >>>>>> uhub4: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus4 >>>>>> ugen5.1: <ATI> at usbus5 >>>>>> uhub5: <ATI EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus5 >>>>>> ad16: 476940MB <Seagate ST3500641NS 3.AEP> at ata8-master UDMA100 SATA >>>>>> 3Gb/s >>>>>> uhub0: 2 ports with 2 removable, self powered >>>>>> uhub1: 2 ports with 2 removable, self powered >>>>>> uhub2: 2 ports with 2 removable, self powered >>>>>> uhub3: 2 ports with 2 removable, self powered >>>>>> uhub4: 2 ports with 2 removable, self powered >>>>>> da8 at mpt0 bus 0 scbus0 target 0 lun 0 >>>>>> da8: <ATA ST31000528AS CC38> Fixed Direct Access SCSI-5 device >>>>>> da8: 300.000MB/s transfers >>>>>> da8: Command Queueing enabled >>>>>> da8: 953869MB (1953525168 512 byte sectors: 255H 63S/T 121601C) >>>>>> da9 at mpt0 bus 0 scbus0 target 1 lun 0 >>>>>> da9: <ATA Hitachi HDS72101 A39C> Fixed Direct Access SCSI-5 device >>>>>> da9: 300.000MB/s transfers >>>>>> da9: Command Queueing enabled >>>>>> da9: 953869MB (1953525168 512 byte sectors: 255H 63S/T 121601C) >>>>>> da10 at mpt0 bus 0 scbus0 target 2 lun 0 >>>>>> da10: <ATA SAMSUNG HD103SJ 00E4> Fixed Direct Access SCSI-5 device >>>>>> da10: 300.000MB/s transfers >>>>>> da10: Command Queueing enabled >>>>>> da10: 953869MB (1953525168 512 byte sectors: 255H 63S/T 121601C) >>>>>> da11 at mpt0 bus 0 scbus0 target 3 lun 0 >>>>>> da11: <ATA SAMSUNG HD103SJ 00E4> Fixed Direct Access SCSI-5 device >>>>>> da11: 300.000MB/s transfers >>>>>> da11: Command Queueing enabled >>>>>> da11: 953869MB (1953525168 512 byte sectors: 255H 63S/T 121601C) >>>>>> da12 at mpt0 bus 0 scbus0 target 4 lun 0 >>>>>> da12: <ATA SAMSUNG HD103SI 1118> Fixed Direct Access SCSI-5 device >>>>>> da12: 300.000MB/s transfers >>>>>> da12: Command Queueing enabled >>>>>> da12: 953869MB (1953525168 512 byte sectors: 255H 63S/T 121601C) >>>>>> da13 at mpt0 bus 0 scbus0 target 5 lun 0 >>>>>> da13: <ATA SAMSUNG HD103SI 1118> Fixed Direct Access SCSI-5 device >>>>>> da13: 300.000MB/s transfers >>>>>> da13: Command Queueing enabled >>>>>> da13: 953869MB (1953525168 512 byte sectors: 255H 63S/T 121601C) >>>>>> da14 at mpt0 bus 0 scbus0 target 6 lun 0 >>>>>> da14: <ATA Hitachi HDS72101 A39C> Fixed Direct Access SCSI-5 device >>>>>> da14: 300.000MB/s transfers >>>>>> da14: Command Queueing enabled >>>>>> da14: 953869MB (1953525168 512 byte sectors: 255H 63S/T 121601C) >>>>>> da0 at mpt1 bus 0 scbus1 target 0 lun 0 >>>>>> da0: <ATA Hitachi HDS5C302 A580> Fixed Direct Access SCSI-5 device >>>>>> da0: 300.000MB/s transfers >>>>>> da0: Command Queueing enabled >>>>>> da0: 1907729MB (3907029168 512 byte sectors: 255H 63S/T 243201C) >>>>>> da1 at mpt1 bus 0 scbus1 target 1 lun 0 >>>>>> da1: <ATA Hitachi HDS5C302 A580> Fixed Direct Access SCSI-5 device >>>>>> da1: 300.000MB/s transfers >>>>>> da1: Command Queueing enabled >>>>>> da1: 1907729MB (3907029168 512 byte sectors: 255H 63S/T 243201C) >>>>>> da2 at mpt1 bus 0 scbus1 target 2 lun 0 >>>>>> da2: <ATA Hitachi HDS5C302 A580> Fixed Direct Access SCSI-5 device >>>>>> da2: 300.000MB/s transfers >>>>>> da2: Command Queueing enabled >>>>>> da2: 1907729MB (3907029168 512 byte sectors: 255H 63S/T 243201C) >>>>>> da3 at mpt1 bus 0 scbus1 target 3 lun 0 >>>>>> da3: <ATA Hitachi HDS5C302 A580> Fixed Direct Access SCSI-5 device >>>>>> da3: 300.000MB/s transfers >>>>>> da3: Command Queueing enabled >>>>>> da3: 1907729MB (3907029168 512 byte sectors: 255H 63S/T 243201C) >>>>>> da4 at mpt1 bus 0 scbus1 target 4 lun 0 >>>>>> da4: <ATA Hitachi HDS5C302 A580> Fixed Direct Access SCSI-5 device >>>>>> da4: 300.000MB/s transfers >>>>>> da4: Command Queueing enabled >>>>>> da4: 1907729MB (3907029168 512 byte sectors: 255H 63S/T 243201C) >>>>>> da5 at mpt1 bus 0 scbus1 target 5 lun 0 >>>>>> da5: <ATA SAMSUNG HD103SI 1118> Fixed Direct Access SCSI-5 device >>>>>> da5: 300.000MB/s transfers >>>>>> da5: Command Queueing enabled >>>>>> da5: 953869MB (1953525168 512 byte sectors: 255H 63S/T 121601C) >>>>>> da6 at mpt1 bus 0 scbus1 target 6 lun 0 >>>>>> da6: <ATA ST31000340AS SD04> Fixed Direct Access SCSI-5 device >>>>>> da6: 300.000MB/s transfers >>>>>> da6: Command Queueing enabled >>>>>> da6: 953869MB (1953525168 512 byte sectors: 255H 63S/T 121601C) >>>>>> da7 at mpt1 bus 0 scbus1 target 7 lun 0 >>>>>> da7: <ATA SAMSUNG HD103SI 1118> Fixed Direct Access SCSI-5 device >>>>>> da7: 300.000MB/s transfers >>>>>> da7: Command Queueing enabled >>>>>> da7: 953869MB (1953525168 512 byte sectors: 255H 63S/T 121601C) >>>>>> SMP: AP CPU #1 Launched! >>>>>> uhub5: 10 ports with 10 removable, self powered >>>>>> GEOM: da7: geometry does not match label (16h,63s != 255h,63s). >>>>>> Trying to mount root from ufs:/dev/ad16s1a >>>>>> WARNING: / was not properly dismounted >>>>>> ZFS filesystem version 5 >>>>>> ZFS storage pool version 28 >>>>>> WARNING: /tmp was not properly dismounted >>>>>> WARNING: /usr was not properly dismounted >>>>>> WARNING: /var was not properly dismounted >>>>>> 0 >>>>>> mpt1: request 0xffffff80002c57f0:2369 timed out for ccb >>>>>> 0xffffff00063bb000 >>>>>> (req->ccb 0xffffff00063bb000) >>>>>> mpt1: attempting to abort req 0xffffff80002c57f0:2369 function 0 >>>>>> mpt1: mpt_wait_req(1) timed out >>>>>> mpt1: mpt_recover_commands: abort timed-out. Resetting controller >>>>>> mpt1: mpt_cam_event: 0x80 >>>>>> mpt1: mpt_cam_event: 0x80 >>>>>> mpt1: completing timedout/aborted req 0xffffff80002c57f0:2369 >>>>>> mpt1: mpt_cam_event: 0x16 >>>>>> mpt1: mpt_cam_event: 0x12 >>>>>> mpt1: mpt_cam_event: 0x12 >>>>>> mpt1: mpt_cam_event: 0x12 >>>>>> mpt1: mpt_cam_event: 0x12 >>>>>> mpt1: mpt_cam_event: 0x12 >>>>>> mpt1: mpt_cam_event: 0x12 >>>>>> mpt1: mpt_cam_event: 0x12 >>>>>> mpt1: mpt_cam_event: 0x12 >>>>>> mpt1: mpt_cam_event: 0x16 >>>>>> mpt1: request 0xffffff80002c5c70:2375 timed out for ccb >>>>>> 0xffffff00063bb000 >>>>>> (req->ccb 0xffffff00063bb000) >>>>>> mpt1: attempting to abort req 0xffffff80002c5c70:2375 function 0 >>>>>> mpt1: completing timedout/aborted req 0xffffff80002c5c70:2375 >>>>>> mpt1: >>>>>> abort of req 0xffffff80002c5c70:0 completed >>>>>> mpt1: mpt_cam_event: 0x16 >>>>>> mpt1: mpt_cam_event: 0x16 >>>>>> mpt1: request 0xffffff80002c5fd0:2379 timed out for ccb >>>>>> 0xffffff00063bb000 >>>>>> (req->ccb 0xffffff00063bb000) >>>>>> mpt1: attempting to abort req 0xffffff80002c5fd0:2379 function 0 >>>>>> mpt1: completing timedout/aborted req 0xffffff80002c5fd0:2379 >>>>>> mpt1: >>>>>> abort of req 0xffffff80002c5fd0:0 completed >>>>>> mpt1: mpt_cam_event: 0x16 >>>>>> mpt1: mpt_cam_event: 0x16 >>>>>> mpt1: request 0xffffff80002c6210:2383 timed out for ccb >>>>>> 0xffffff00063bb000 >>>>>> (req->ccb 0xffffff00063bb000) >>>>>> mpt1: attempting to abort req 0xffffff80002c6210:2383 function 0 >>>>>> mpt1: completing timedout/aborted req 0xffffff80002c6210:2383 >>>>>> mpt1: >>>>>> abort of req 0xffffff80002c6210:0 completed >>>>>> mpt1: mpt_cam_event: 0x16 >>>>>> mpt1: mpt_cam_event: 0x16 >>>>>> mpt1: request 0xffffff80002c6180:2387 timed out for ccb >>>>>> 0xffffff00063bb000 >>>>>> (req->ccb 0xffffff00063bb000) >>>>>> mpt1: attempting to abort req 0xffffff80002c6180:2387 function 0 >>>>>> mpt1: completing timedout/aborted req 0xffffff80002c6180:2387 >>>>>> mpt1: >>>>>> abort of req 0xffffff80002c6180:0 completed >>>>>> mpt1: mpt_cam_event: 0x16 >>>>>> mpt1: mpt_cam_event: 0x16 >>>>>> mpt1: request 0xffffff80002c62a0:2391 timed out for ccb >>>>>> 0xffffff00063bb000 >>>>>> (req->ccb 0xffffff00063bb000) >>>>>> mpt1: attempting to abort req 0xffffff80002c62a0:2391 function 0 >>>>>> mpt1: completing timedout/aborted req 0xffffff80002c62a0:2391 >>>>>> mpt1: >>>>>> abort of req 0xffffff80002c62a0:0 completed >>>>>> mpt1: mpt_cam_event: 0x16 >>>>>> mpt1: mpt_cam_event: 0x16 >>>>>> mpt1: request 0xffffff80002c6720:2395 timed out for ccb >>>>>> 0xffffff00063bb000 >>>>>> (req->ccb 0xffffff00063bb000) >>>>>> mpt1: attempting to abort req 0xffffff80002c6720:2395 function 0 >>>>>> mpt1: completing timedout/aborted req 0xffffff80002c6720:2395 >>>>>> mpt1: >>>>>> abort of req 0xffffff80002c6720:0 completed >>>>>> mpt1: mpt_cam_event: 0x16 >>>>>> mpt1: mpt_cam_event: 0x16 >>>>>> mpt1: request 0xffffff80002c67b0:2399 timed out for ccb >>>>>> 0xffffff00063bb000 >>>>>> (req->ccb 0xffffff00063bb000) >>>>>> mpt1: attempting to abort req 0xffffff80002c67b0:2399 function 0 >>>>>> mpt1: completing timedout/aborted req 0xffffff80002c67b0:2399 >>>>>> mpt1: >>>>>> abort of req 0xffffff80002c67b0:0 completed >>>>>> mpt1: mpt_cam_event: 0x16 >>>>>> mpt1: mpt_cam_event: 0x16 >>>>>> mpt0: request 0xffffff80002a69e0:2082 timed out for ccb >>>>>> 0xffffff0006389800 >>>>>> (req->ccb 0xffffff0006389800) >>>>>> mpt0: attempting to abort req 0xffffff80002a69e0:2082 function 0 >>>>>> mpt0: completing timedout/aborted req 0xffffff80002a69e0:2082 >>>>>> mpt0: abort of req 0xffffff80002a69e0:0 completed >>>>>> mpt0: mpt_cam_event: 0x16 >>>>>> mpt0: mpt_cam_event: 0x16 >>>>>> mpt0: request 0xffffff80002a6c20:2086 timed out for ccb >>>>>> 0xffffff0006389800 >>>>>> (req->ccb 0xffffff0006389800) >>>>>> mpt0: attempting to abort req 0xffffff80002a6c20:2086 function 0 >>>>>> mpt0: completing timedout/aborted req 0xffffff80002a6c20:2086 >>>>>> mpt0: abort of req 0xffffff80002a6c20:0 completed >>>>>> mpt0: mpt_cam_event: 0x16 >>>>>> mpt0: mpt_cam_event: 0x16 >>>>>> mpt0: request 0xffffff80002a6cb0:2090 timed out for ccb >>>>>> 0xffffff0006389800 >>>>>> (req->ccb 0xffffff0006389800) >>>>>> mpt0: attempting to abort req 0xffffff80002a6cb0:2090 function 0 >>>>>> mpt0: completing timedout/aborted req 0xffffff80002a6cb0:2090 >>>>>> mpt0: abort of req 0xffffff80002a6cb0:0 completed >>>>>> mpt0: mpt_cam_event: 0x16 >>>>>> mpt0: mpt_cam_event: 0x16 >>>>>> mpt0: request 0xffffff80002a6b90:2094 timed out for ccb >>>>>> 0xffffff0006389800 >>>>>> (req->ccb 0xffffff0006389800) >>>>>> mpt0: attempting to abort req 0xffffff80002a6b90:2094 function 0 >>>>>> mpt0: completing timedout/aborted req 0xffffff80002a6b90:2094 >>>>>> mpt0: abort of req 0xffffff80002a6b90:0 completed >>>>>> mpt0: mpt_cam_event: 0x16 >>>>>> mpt0: mpt_cam_event: 0x16 >>>>>> tun0: link state changed to UP >>>>>> (da8:mpt0:0:0:0): READ(10). CDB: 28 0 3e e2 6f 56 0 0 1 0 >>>>>> (da8:mpt0:0:0:0): CAM status: SCSI Status Error >>>>>> (da8:mpt0:0:0:0): SCSI status: Check Condition >>>>>> (da8:mpt0:0:0:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, >>>>>> reset, or >>>>>> bus device reset occurred) >>>>>> (da11:mpt0:0:3:0): READ(10). CDB: 28 0 1a b6 92 0 0 0 80 0 >>>>>> (da11:mpt0:0:3:0): CAM status: SCSI Status Error >>>>>> (da11:mpt0:0:3:0): SCSI status: Check Condition >>>>>> (da11:mpt0:0:3:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, >>>>>> reset, or >>>>>> bus device reset occurred) >>>>>> (da2:mpt1:0:2:0): READ(10). CDB: 28 0 76 7b de 0 0 0 80 0 >>>>>> (da2:mpt1:0:2:0): CAM status: SCSI Status Error >>>>>> (da2:mpt1:0:2:0): SCSI status: Check Condition >>>>>> (da2:mpt1:0:2:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, >>>>>> reset, or >>>>>> bus device reset occurred) >>>>>> (da10:mpt0:0:2:0): READ(10). CDB: 28 0 1a ff 67 80 0 0 80 0 >>>>>> (da10:mpt0:0:2:0): CAM status: SCSI Status Error >>>>>> (da10:mpt0:0:2:0): SCSI status: Check Condition >>>>>> (da10:mpt0:0:2:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, >>>>>> reset, or >>>>>> bus device reset occurred) >>>>>> (da5:mpt1:0:5:0): READ(10). CDB: 28 0 1a ff 67 80 0 0 80 0 >>>>>> (da5:mpt1:0:5:0): CAM status: SCSI Status Error >>>>>> (da5:mpt1:0:5:0): SCSI status: Check Condition >>>>>> (da5:mpt1:0:5:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, >>>>>> reset, or >>>>>> bus device reset occurred) >>>>>> (da7:mpt1:0:7:0): READ(10). CDB: 28 0 40 d7 da 80 0 0 80 0 >>>>>> (da7:mpt1:0:7:0): CAM status: SCSI Status Error >>>>>> (da7:mpt1:0:7:0): SCSI status: Check Condition >>>>>> (da7:mpt1:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, >>>>>> reset, or >>>>>> bus device reset occurred) >>>>>> (da6:mpt1:0:6:0): READ(10). CDB: 28 0 40 d7 da 80 0 0 80 0 >>>>>> (da6:mpt1:0:6:0): CAM status: SCSI Status Error >>>>>> (da6:mpt1:0:6:0): SCSI status: Check Condition >>>>>> (da6:mpt1:0:6:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, >>>>>> reset, or >>>>>> bus device reset occurred) >>>>>> (da0:mpt1:0:0:0): READ(10). CDB: 28 0 76 91 87 e3 0 0 1 0 >>>>>> (da0:mpt1:0:0:0): CAM status: SCSI Status Error >>>>>> (da0:mpt1:0:0:0): SCSI status: Check Condition >>>>>> (da0:mpt1:0:0:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, >>>>>> reset, or >>>>>> bus device reset occurred) >>>>>> (da3:mpt1:0:3:0): READ(10). CDB: 28 0 76 69 1 1c 0 0 1 0 >>>>>> (da3:mpt1:0:3:0): CAM status: SCSI Status Error >>>>>> (da3:mpt1:0:3:0): SCSI status: Check Condition >>>>>> (da3:mpt1:0:3:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, >>>>>> reset, or >>>>>> bus device reset occurred) >>>>>> (da1:mpt1:0:1:0): READ(10). CDB: 28 0 76 69 1 1c 0 0 1 0 >>>>>> (da1:mpt1:0:1:0): CAM status: SCSI Status Error >>>>>> (da1:mpt1:0:1:0): SCSI status: Check Condition >>>>>> (da1:mpt1:0:1:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, >>>>>> reset, or >>>>>> bus device reset occurred) >>>>>> (da9:mpt0:0:1:0): READ(10). CDB: 28 0 1a b3 d7 0 0 0 80 0 >>>>>> (da9:mpt0:0:1:0): CAM status: SCSI Status Error >>>>>> (da9:mpt0:0:1:0): SCSI status: Check Condition >>>>>> (da9:mpt0:0:1:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, >>>>>> reset, or >>>>>> bus device reset occurred) >>>>>> (da4:mpt1:0:4:0): READ(10). CDB: 28 0 53 3c c6 0 0 0 80 0 >>>>>> (da4:mpt1:0:4:0): CAM status: SCSI Status Error >>>>>> (da4:mpt1:0:4:0): SCSI status: Check Condition >>>>>> (da4:mpt1:0:4:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, >>>>>> reset, or >>>>>> bus device reset occurred) >>>>>> >>>>>> >>>>>> >>>>>> > >>>>>> > -- >>>>>> > | Jeremy Chadwick >>>>>> jdc@parodius.com | >>>>>> > | Parodius Networking >>>>>> http://www.parodius.com/ | >>>>>> > | UNIX Systems Administrator Mountain View, CA, US >>>>>> | >>>>>> > | Making life hard for others since 1977. PGP 4BD6C0CB >>>>>> | >>>>>> > >>>>>> > >>>>>> >>>>>> >>>>>> -- >>>>>> Joshua Boyd >>>>>> _______________________________________________ >>>>>> freebsd-stable@freebsd.org mailing list >>>>>> http://lists.freebsd.org/mailman/listinfo/freebsd-stable >>>>>> To unsubscribe, send any mail to " >>>>>> freebsd-stable-unsubscribe@freebsd.org" >>>>>> >>>>> >>>>> >>>> >>>> >>>> -- >>>> Joshua Boyd >>>> >>> >>> >>> >>> -- >>> Joshua Boyd >>> >>> >>> E-mail: boydjd@jbip.net >>> http://www.jbip.net >>> >> >> > > > -- > Joshua Boyd > > E-mail: boydjd@jbip.net > http://www.jbip.net >
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?BANLkTi=6ssM3uMvkx3OqfbWJ0%2BaV75mXZg>