Date: Tue, 30 Jan 2001 19:50:51 -0200 From: "Alessandro Nunes" <nunes@corp.terra.com.br> To: "G D McKee" <freebsd@gdmckee.com>, "FreeBSD Questions" <FreeBSD-questions@FreeBSD.ORG> Subject: RE: Can't mount CD-ROM (acd0: READ_TOC command timeout - resetting) Message-ID: <JFEEIBJBNCCBDBFPJMPOIEKKCKAA.nunes@corp.terra.com.br> In-Reply-To: <000a01c08b05$55642e20$0500a8c0@gdmckee.local>
next in thread | previous in thread | raw e-mail | index | archive | help
CD Drive is on AUTO (PIO3) and there's no option to put it on PIO4. Thanks. ----------------------- Alessandro Nunes nunes@corp.terra.com.br Terra Networks Brasil #-----Original Message----- #From: G D McKee [mailto:freebsd@gdmckee.com] #Sent: ter=E7a-feira, 30 de janeiro de 2001 19:41 #To: Alessandro Nunes; FreeBSD Questions #Subject: Re: Can't mount CD-ROM (acd0: READ_TOC command timeout - #resetting) # # #Hi # #I would force the CD Drive to mode 4 in the BIOS and see if that = corrects #it, or just leave it on AUTO and all should be fine. # #G D McKee # #----- Original Message ----- #From: "Alessandro Nunes" <nunes@corp.terra.com.br> #To: "FreeBSD Questions" <FreeBSD-questions@FreeBSD.ORG> #Sent: Tuesday, January 30, 2001 9:29 PM #Subject: Can't mount CD-ROM (acd0: READ_TOC command timeout - = resetting) # # #> Hi, #> #> I've installed a RELEASE-4.2 in a IBM Netfinity 5000 via #> FTP because the installation hangs when I tried to read CD-ROM. #> The host is running ok but CD continues not working. #> Strange messages appear when the system try to recognize "ata0" #> on boot (see below in "dmesg.boot"). #> The CD-ROM drive is using PIO3 in BIOS setup but ata0-master is using #PIO4. #> #> How can CD-ROM work properly? #> Thanks for any help. #> #> mount /cdrom #> =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D #> Command "mount /cdrom" doesn't return a prompt and #> I have to use ^C to get prompt back. #> Below "/var/log/messages" after I've tried mounting CDROM. #> #> Jan 30 16:28:39 ivc3 /kernel: acd0: READ_TOC command timeout - = resetting #> Jan 30 16:28:39 ivc3 /kernel: ata0: resetting devices .. done #> Jan 30 16:28:39 ivc3 /kernel: acd0: read data overrun 12/0 #> Jan 30 16:29:09 ivc3 /kernel: acd0: READ_TOC command timeout - = resetting #> Jan 30 16:29:09 ivc3 /kernel: ata0: resetting devices .. done #> Jan 30 16:29:09 ivc3 /kernel: acd0: read data overrun 12/0 #> Jan 30 16:29:40 ivc3 /kernel: acd0: READ_BIG command timeout - = resetting #> Jan 30 16:29:40 ivc3 /kernel: ata0: resetting devices .. done #> Jan 30 16:30:10 ivc3 /kernel: acd0: READ_BIG command timeout - = resetting #> Jan 30 16:30:10 ivc3 /kernel: ata0: resetting devices .. done #> Jan 30 16:30:40 ivc3 /kernel: acd0: READ_BIG command timeout - = resetting #> Jan 30 16:30:40 ivc3 /kernel: ata0: resetting devices .. done #> Jan 30 16:31:10 ivc3 /kernel: acd0: READ_BIG command timeout - = resetting #> Jan 30 16:31:10 ivc3 /kernel: ata0: resetting devices .. done #> #> #> dmesg.boot #> =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D #> #> Copyright (c) 1992-2000 The FreeBSD Project. #> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, = 1994 #> The Regents of the University of California. All rights = reserved. #> FreeBSD 4.2-RELEASE #0: Tue Jan 9 17:30:25 BRST 2001 #> root@ivc3.terra.com.br:/usr/src/sys/compile/TERRA #> Timecounter "i8254" frequency 1193182 Hz #> CPU: Pentium III/Pentium III Xeon/Celeron (598.40-MHz 686-class CPU) #> Origin =3D "GenuineIntel" Id =3D 0x673 Stepping =3D 3 #> #Features=3D0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR #,PGE,MCA, #CM #> OV,PAT,PSE36,MMX,FXSR,SSE> #> real memory =3D 268419072 (262128K bytes) #> avail memory =3D 258265088 (252212K bytes) #> Programming 24 pins in IOAPIC #0 #> IOAPIC #0 intpin 2 -> irq 0 #> FreeBSD/SMP: Multiprocessor motherboard #> cpu0 (BSP): apic id: 1, version: 0x00040011, at 0xfee00000 #> cpu1 (AP): apic id: 0, version: 0x00040011, at 0xfee00000 #> io0 (APIC): apic id: 14, version: 0x00170011, at 0xfec00000 #> Preloaded elf kernel "kernel" at 0xc030f000. #> Pentium Pro MTRR support enabled #> md0: Malloc disk #> npx0: <math processor> on motherboard #> npx0: INT 16 interface #> pcib0: <Host to PCI bridge> on motherboard #> pci0: <PCI bus> on pcib0 #> fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0x2000-0x201f mem #0xfea00000-0xfeaf #> ffff,0xfebff000-0xfebfffff irq 11 at device 1.0 on pci0 #> fxp0: Ethernet address 00:04:ac:33:ea:0d #> ahc0: <Adaptec aic7895 Ultra SCSI adapter> port 0x2200-0x22ff mem #0xfebfe000-0xf #> ebfefff irq 15 at device 6.0 on pci0 #> aic7895C: Wide Channel A, SCSI Id=3D7, 32/255 SCBs #> ahc1: <Adaptec aic7895 Ultra SCSI adapter> port 0x2300-0x23ff mem #0xfebfd000-0xf #> ebfdfff irq 10 at device 6.1 on pci0 #> aic7895C: Wide Channel B, SCSI Id=3D7, 32/255 SCBs #> pci0: <unknown card> (vendor=3D0x1022, dev=3D0x2000) at 9.0 irq 11 #> pci0: <S3 Trio 64V2/DX/GX graphics accelerator> at 10.0 irq 9 #> isab0: <ServerWorks IB6566 PCI to ISA bridge> at device 15.0 on pci0 #> isa0: <ISA bus> on isab0 #> atapci0: <Generic PCI ATA controller> port #0xffa0-0xffaf,0-0x3,0-0x7,0x3f4-0x3f7 #> ,0x1f0-0x1f7 irq 10 at device 15.1 on pci0 #> ata0: at 0x1f0 irq 14 on atapci0 #> pci0: <OHCI USB controller> at 15.2 irq 10 #> pcib1: <ServerWorks NB6536 2.0HE host to PCI bridge> on motherboard #> pci1: <PCI bus> on pcib1 #> fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on = isa0 #> fdc0: FIFO enabled, 8 bytes threshold #> fd0: <1440-KB 3.5" drive> on fdc0 drive 0 #> atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 #> atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 #> kbd0 at atkbd0 #> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on = isa0 #> sc0: <System console> at flags 0x100 on isa0 #> sc0: VGA <16 virtual consoles, flags=3D0x300> #> sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 #> sio0: type 16550A #> sio1 at port 0x2f8-0x2ff irq 3 on isa0 #> sio1: type 16550A #> ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0 #> ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode #> ppi0: <Parallel I/O> on ppbus0 #> plip0: <PLIP network interface> on ppbus0 #> lpt0: <Printer> on ppbus0 #> lpt0: Interrupt-driven port #> APIC_IO: Testing 8254 interrupt delivery #> APIC_IO: routing 8254 via IOAPIC #0 intpin 2 #> SMP: AP CPU #1 Launched! #> (null): MODE_SENSE_BIG command timeout - resetting #> ata0: resetting devices .. done #> (null): read data overrun 28/2 #> acd0: CDROM <CRD-8322B> at ata0-master using PIO4 #> Waiting 15 seconds for SCSI devices to settle #> pass1 at ahc1 bus 0 target 14 lun 0 #> pass1: <SDR GEM200 2> Fixed Processor SCSI-2 device #> pass1: 3.300MB/s transfersMounting root from ufs:/dev/da0s1a #> da0 at ahc1 bus 0 target 0 lun 0 #> da0: <IBM-PSG ST39103LC !# B222> Fixed Direct Access SCSI-2 = device #> da0: 11.626MB/s transfers (5.813MHz, offset 8, 16bit), Tagged = Queueing #Enabled #> da0: 8678MB (17774160 512 byte sectors: 255H 63S/T 1106C) #> #> #> ----------------------- #> Alessandro Nunes #> nunes@corp.terra.com.br #> Terra Networks Brasil #> #> #> #> To Unsubscribe: send mail to majordomo@FreeBSD.org #> with "unsubscribe freebsd-questions" in the body of the message #> #> #> # # To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?JFEEIBJBNCCBDBFPJMPOIEKKCKAA.nunes>