Date: Tue, 28 Jul 1998 01:33:26 -0700 (PDT) From: Brandon Huey <bh@synergy.transbay.net> To: Eddie Irvine <eirvine@tpgi.com.au> Cc: Guy <guy@lisp.com.au>, freebsd-questions@FreeBSD.ORG Subject: Re: Network Cards Message-ID: <Pine.BSF.3.96.980728013019.5872B-100000@synergy.transbay.net> In-Reply-To: <01bdb9f6$9b4c3c80$a41a1acb@gretchen>
next in thread | previous in thread | raw e-mail | index | archive | help
that's a lot of work that $34.99 could eliminate. maybe pick a better-supported interface to start with, like the netgear fa310tx. based on the dec 21140 chipset and has very efficient support in freebsd. many ne2000 clones don't even have onboard memory. On Tue, 28 Jul 1998, Eddie Irvine wrote: > > From: Guy <guy@lisp.com.au> > > > When I was setting up FreeBSD it was the NIC cards that gave me the > biggest and longest headache. Like you I was using an NE2000 ed0 card. > > Some pointers as requested: > > 1 Figure out what interrupt FreeBSD thinks the ed0 card is on (you say > it is IRQ 10 ...) then use the disk that came with the card to check > that the card really is set to IRQ10 in its CMOS, and set to simplex, > not > duplex. You'll have to boot up from a DOS floppy to do this :(. > Turn off Pnp while you're at it. > > 2 Turn off Pnp in system CMOS for the IRQ that the card is on. > (delete key on boot). > > 3 Do you know how to compile a custom kernel? I actually have my ed0 > card > set to IRQ 5 in the kernel, on the card's CMOS, and in the system > CMOS. > > 4 "Device timeouts" are often caused by faulty connectors/flyleads/hubs > not on. > Probably check this *FIRST*. > > 5 ed1 is an NE2000 card in the PCI bus. If you have an ed0 device in the > kernel > it often requires no further configuration. > > 6 It should work. I now have one NE2000 card in the ISA bus and two on > the PCI > bus, and route between three LANs. FTP gets up to 800 k/sec. > > > >Hi, > >I have just re-installed freebsd, and my network card is not working > >correctly (which it was prior to the re-install), the only difference > >being that i added a scsi card and 2 scsi hard drives. None of which are > >using irq ,dma, or ports which are used by other peripherals. I have set > >it up correctly in the kernal configuration, to its correct settings > >(irq 10 port 0x6000), but on boot (when the system is setting the > >default gateway )i get the msg ed0: Device timeout. On the next line > >after this i get - ed1: NIC Memory corrupt - inv alid packet length 64.. > >I have only the one network card. Another strange thing is that ed1 does > >not appear in the kernel configuration, although it is present in the > >network configuration in /stand/sysinstall. I have been looking > >everywhere for what is causing this problem but to no avail. So if > >anyone can help me with this problem it would be greatly appreciated. > >Regards > >Guy Coble > > > Good luck. > Eddie. > > > To Unsubscribe: send mail to majordomo@FreeBSD.org > with "unsubscribe freebsd-questions" in the body of the message > To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.BSF.3.96.980728013019.5872B-100000>