Date: Fri, 26 Nov 2021 12:40:42 -0800 From: Mark Millard via freebsd-arm <freebsd-arm@freebsd.org> To: Juan David Hurtado G <jdhurtado@orbiware.com> Cc: Free BSD <freebsd-arm@freebsd.org> Subject: Re: 13.0-RELEASE Poor performance on Raspberry pi 3 B+ Message-ID: <4D1EFC3E-2665-47B6-9A2F-09E7F22907D0@yahoo.com> In-Reply-To: <0D62833A-295A-4DC7-AC7D-7A86FA06F89B@yahoo.com> References: <CAL3Ut_bFZhWKThHJsPaa%2BP0JXH6-=e3Pxv3xF3Y0u9dXpQ3kZQ@mail.gmail.com> <CAL3Ut_Y_BLbGM1WZ%2B8JbkSp9F=s9_xcWbFikLpcOufioxd1m_g@mail.gmail.com> <20211124155352.GA26072@www.zefox.net> <6CCD061E-DCDA-46E0-AE19-76EA1B30E56F@yahoo.com> <CAL3Ut_ZQO2WAvJuMqjpsQyCbyqmBVjMrqC%2BjXrid1ovWkpsUjA@mail.gmail.com> <69E3CEF1-87D0-405B-B132-7D6A6A4EA056@yahoo.com> <1229E940-5DAB-4D49-AB14-E804296D10BC@yahoo.com> <CAL3Ut_Y-S7GGmTfFApG5Vn9vkaMFDmMfWR23OSQyf=sCtVHqbg@mail.gmail.com> <B7B3B795-DC22-47C6-A42F-94588DDDDDBD@yahoo.com> <CAL3Ut_akBgXCc_hNHL%2BpPDzhp8CcMmcf4Jar5EUH1r6kmAz-rg@mail.gmail.com> <f4ee3ca1-869a-1f90-88b2-da494d7788a5@gmail.com> <CAL3Ut_bYST%2B8eOOy-7sDHo6HdFxnjRJaRccvi90Ac2=_jise-A@mail.gmail.com> <0D62833A-295A-4DC7-AC7D-7A86FA06F89B@yahoo.com>
next in thread | previous in thread | raw e-mail | index | archive | help
On 2021-Nov-26, at 11:04, Mark Millard <marklmi@yahoo.com> wrote: > On 2021-Nov-26, at 10:35, Juan David Hurtado G = <jdhurtado@orbiware.com> wrote: >=20 >> Thank you so much for your time you all. >>=20 >> New microSD arrived today. It is a SanDisk Ultra, see this on the = Raspberry >> pi 3B+: >>=20 >> ``` >> root@generic:~ # dmesg | grep -i mmc >> mmc0: <MMC/SD bus> on sdhci_bcm0 >> mmcsd0: 32GB <SDHC SD32G 8.5 SN A0169EA9 MFG 04/2021 by 3 SD> at mmc0 >> 50.0MHz/4bit/65535-block >> ``` >>=20 >> 50 MHz !! What a relief. >>=20 >> Other OS like RaspiOS and NetBSD runs well on the other cards, not = sure >> why. I still don't understand why sandisk is the only brand that = works for >> FreeBSD apparently. >=20 > I have non-sandisk microsd cards that work fine --and other sandisk > models of microsd cards that also work. Mostly I use non-ultra sandisk > ones as it turns out. Some of these are not intended as high performance for the type of context and some may not perform as well as others, even if intended is high performance. I'm just listing ones that have historically seemed to work okay in my use: Transcend High Endurance microSDHC Kingston microSDHC I Industrial Samsung EVO+ microSDHC I Samsung EVO PLUS microSDXC I SanDisk Extreme microSDHC I (A1) SanDisk Extreme microSDXC I (A2) SanDisk Extreme PLUS microSDXC I (A1) SanDisk Ultra microSDHC I SanDisk Ultra microSDXC I SanDisk Ultra microSDXC I (A1) So far all of these have worked. None of them are recent purchases. I've never observed a small MHz figure for any of them, as far as I remember anyway. I'm not claiming RPi* use of the fastest modes some of the miscrosd cards are capable of. > But once I could boot via USB I no longer use microsd cards very > often in the RPi*'s that can boot from USB without a microsd card > involved. >=20 >> I'm willing to give more information if needed or even to open a = ticket in >> bugzilla if you find it useful. >=20 > It does not seem that my direction of activity is > relevant if it is media-type specific for the behavior. > So I'll not be experimenting further with any RPi4B's > (or otherwise). >=20 > But if you make a bugzilla report, various things about > your RPi* configurations that you have reported would be > appropriate to include as context. >=20 >> Have a great weekend !! >>=20 >> PS: I've also bought the usb ttl cable if I can give any more = information >> using the other card via serial console. >=20 > There are various settings for getting more debug > output on the serial console for the RPi* stages > of things. Some go in the config.txt but one goes > in the eeprom content. As stands it does not seem > that such would have helped for the specific problem: > The problem is later, after the RPi* eeprom and > firmware stages. >=20 > You may never need such, but at least you are forwarned > about the possibility if you think it might help > something in the future. >=20 =3D=3D=3D Mark Millard marklmi at yahoo.com ( dsl-only.net went away in early 2018-Mar)
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?4D1EFC3E-2665-47B6-9A2F-09E7F22907D0>