Skip site navigation (1)Skip section navigation (2)
Date:      Tue, 1 Apr 2003 20:35:36 +0200 (CEST)
From:      Marcel Stangenberger <marcel@hayholt.org>
To:        Jason Stewart <jstewart@rtl.org>
Cc:        freebsd-questions@freebsd.org
Subject:   Re: Smbfs woes
Message-ID:  <Pine.GSO.4.53.0304012034460.7268@eldar.hayholt.org>
In-Reply-To: <1049221900.1448.35.camel@mis3>
References:  <1049220242.1448.19.camel@mis3> <Pine.GSO.4.53.0304012004450.7268@eldar.hayholt.org> <1049221611.1448.33.camel@mis3><1049221900.1448.35.camel@mis3>

next in thread | previous in thread | raw e-mail | index | archive | help
hmm ok, this all seems to be in perfect order (at least to me), if you
reboot the system and load the generic kernel again, does it still work?

-- 
Real programmers don't write in FORTRAN.  FORTRAN is for pipe stress
freaks and crystallography weenies.  FORTRAN is for wimp engineers who
wear white socks.

On Tue, 1 Apr 2003, Jason Stewart wrote:

> Certainly,
> The interface is actually ed1 and it is a pcmcia network card.
>
> ed1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
> 	inet 10.0.0.74 netmask 0xffffff00 broadcast 10.0.0.255
> 	ether 00:04:5a:91:31:ac
> 	media: Ethernet autoselect (100baseTX <full-duplex>)
> 	status: active
>
> Jason
>
>
> On Tue, 2003-04-01 at 13:27, Marcel Stangenberger wrote:
> > hmm odd, this all looks fine, can you paste the output from ifconfig ed0
> > to the list?
> >
> > Marcel
> >
> > --
> > Real programmers don't write in FORTRAN.  FORTRAN is for pipe stress
> > freaks and crystallography weenies.  FORTRAN is for wimp engineers who
> > wear white socks.
> >
> > On Tue, 1 Apr 2003, Jason Stewart wrote:
> >
> > > Must have overlooked in in my cut-and-paste job. Everything else appears
> > > to be intact.
> > >
> > > # PCI Ethernet NICs that use the common MII bus controller code.
> > > # NOTE: Be sure to keep the 'device miibus' line in order to use these
> > > NICs!
> > > device		miibus		# MII bus support
> > >
> > > # ISA Ethernet NICs.
> > > # 'device ed' requires 'device miibus'
> > > device		ed0	at isa? port 0x280 irq 10 iomem 0xd8000
> > >
> > > There it is. Thanks again.
> > > Jason
> > >
> > > On Tue, 2003-04-01 at 13:17, Marcel Stangenberger wrote:
> > > > perhaps i'm overlooking it, but i don't see your network card in here?
> > > >
> > > > Regards,
> > > >
> > > > Marcel
> > > >
> > > > --
> > > > Real programmers don't write in FORTRAN.  FORTRAN is for pipe stress
> > > > freaks and crystallography weenies.  FORTRAN is for wimp engineers who
> > > > wear white socks.
> > > >
> > > > On Tue, 1 Apr 2003, Jason Stewart wrote:
> > > >
> > > > > Here is my Kernel Config:
> > > > >
> > > > > Thanks again.
> > > > > Jason
> > > > >
> > > > > #
> > > > > # GENERIC -- Generic kernel configuration file for FreeBSD/i386
> > > > > #
> > > > > # For more information on this file, please read the handbook section on
> > > > > # Kernel Configuration Files:
> > > > > #
> > > > > #
> > > > > http://www.FreeBSD.org/doc/en_US.ISO8859-1/books/handbook/kernelconfig-config.html
> > > > > #
> > > > > # The handbook is also available locally in /usr/share/doc/handbook
> > > > > # if you've installed the doc distribution, otherwise always see the
> > > > > # FreeBSD World Wide Web server (http://www.FreeBSD.org/) for the
> > > > > # latest information.
> > > > > #
> > > > > # An exhaustive list of options and more detailed explanations of the
> > > > > # device lines is also present in the ./LINT configuration file. If you
> > > > > are
> > > > > # in doubt as to the purpose or necessity of a line, check first in
> > > > > LINT.
> > > > > #
> > > > > # $FreeBSD$
> > > > >
> > > > > machine		i386
> > > > > cpu		I686_CPU
> > > > > ident		MIS3C
> > > > > maxusers	0
> > > > >
> > > > > #makeoptions	DEBUG=-g		#Build kernel with gdb(1) debug symbols
> > > > >
> > > > > options 	INET			#InterNETworking
> > > > > options 	FFS			#Berkeley Fast Filesystem
> > > > > options 	FFS_ROOT		#FFS usable as root device [keep this!]
> > > > > options 	SOFTUPDATES		#Enable FFS soft updates support
> > > > > options 	UFS_DIRHASH		#Improve performance on big directories
> > > > > options 	MFS			#Memory Filesystem
> > > > > options 	MD_ROOT			#MD is a potential root device
> > > > > options 	NFS			#Network Filesystem
> > > > > options 	NFS_ROOT		#NFS usable as root device, NFS required
> > > > > options 	MSDOSFS			#MSDOS Filesystem
> > > > > options 	CD9660			#ISO 9660 Filesystem
> > > > > options 	CD9660_ROOT		#CD-ROM usable as root, CD9660 required
> > > > > options 	PROCFS			#Process filesystem
> > > > > options 	COMPAT_43		#Compatible with BSD 4.3 [KEEP THIS!]
> > > > > options 	SCSI_DELAY=15000	#Delay (in ms) before probing SCSI
> > > > > options 	UCONSOLE		#Allow users to grab the console
> > > > > options 	USERCONFIG		#boot -c editor
> > > > > options 	VISUAL_USERCONFIG	#visual boot -c editor
> > > > > options 	KTRACE			#ktrace(1) support
> > > > > options 	SYSVSHM			#SYSV-style shared memory
> > > > > options 	SYSVMSG			#SYSV-style message queues
> > > > > options 	SYSVSEM			#SYSV-style semaphores
> > > > > options		USER_LDT		# Wine                                 options
> > > > > 	       P1003_1B		       #Posix P1003_1B real-time extensions
> > > > > options 	_KPOSIX_PRIORITY_SCHEDULING
> > > > > options 	ICMP_BANDLIM		#Rate limit bad replies
> > > > > options 	KBD_INSTALL_CDEV	# install a CDEV entry in /dev
> > > > > options 	AHC_REG_PRETTY_PRINT	# Print register bitfields in debug
> > > > > 					# output.  Adds ~128k to driver.
> > > > > options 	AHD_REG_PRETTY_PRINT	# Print register bitfields in debug
> > > > > 					# output.  Adds ~215k to driver.
> > > > >
> > > > > # Networking
> > > > > options 	IPX			#IPX/SPX communications protocols
> > > > > options 	NCP			#NetWare Core protocol
> > > > >
> > > > > # SMB/CIFS requester
> > > > > # NETSMB enables support for SMB protocol, it requires LIBMCHAIN and
> > > > > LIBICONV
> > > > > # options.
> > > > > # NETSMBCRYPTO enables support for encrypted passwords.
> > > > > options 	NETSMB			#SMB/CIFS requester
> > > > > options 	NETSMBCRYPTO		#encrypted password support for SMB
> > > > > options 	LIBMCHAIN		#mbuf management library
> > > > > options 	LIBICONV
> > > > > options 	SMBFS
> > > > >
> > > > > device		isa
> > > > > device		pci
> > > > >
> > > > > # Sound Driver
> > > > > device		pcm
> > > > >
> > > > > # Floppy drives
> > > > > device		fdc0	at isa? port IO_FD1 irq 6 drq 2
> > > > > device		fd0	at fdc0 drive 0
> > > > > device		fd1	at fdc0 drive 1
> > > > > #
> > > > > # If you have a Toshiba Libretto with its Y-E Data PCMCIA floppy,
> > > > > # don't use the above line for fdc0 but the following one:
> > > > > #device		fdc0
> > > > >
> > > > > # ATA and ATAPI devices
> > > > > device		ata0	at isa? port IO_WD1 irq 14
> > > > > device		ata1	at isa? port IO_WD2 irq 15
> > > > > device		ata
> > > > > device		atadisk			# ATA disk drives
> > > > > device		atapicd			# ATAPI CDROM drives
> > > > > device		atapifd			# ATAPI floppy drives
> > > > > options 	ATA_STATIC_ID		#Static device numbering
> > > > >
> > > > >
> > > > > # atkbdc0 controls both the keyboard and the PS/2 mouse
> > > > > device		atkbdc0	at isa? port IO_KBD
> > > > > device		atkbd0	at atkbdc? irq 1 flags 0x1
> > > > > device		psm0	at atkbdc? irq 12
> > > > >
> > > > > device		vga0	at isa?
> > > > >
> > > > > # splash screen/screen saver
> > > > > pseudo-device	splash
> > > > >
> > > > > # syscons is the default console driver, resembling an SCO console
> > > > > device		sc0	at isa? flags 0x100
> > > > >
> > > > > # Floating point support - do not disable.
> > > > > device		npx0	at nexus? port IO_NPX irq 13
> > > > >
> > > > > # Power management support (see LINT for more options)
> > > > > device		apm0	at nexus? disable flags 0x20 # Advanced Power Management
> > > > >
> > > > > # PCCARD (PCMCIA) support
> > > > > device		card
> > > > > device		pcic0	at isa? irq 0 port 0x3e0 iomem 0xd0000
> > > > > device		pcic1	at isa? irq 0 port 0x3e2 iomem 0xd4000 disable
> > > > >
> > > > > # Serial (COM) ports
> > > > > device		sio0	at isa? port IO_COM1 flags 0x10 irq 4
> > > > > device		sio1	at isa? port IO_COM2 irq 3
> > > > > device		sio2	at isa? disable port IO_COM3 irq 5
> > > > > device		sio3	at isa? disable port IO_COM4 irq 9
> > > > >
> > > > > # Parallel port
> > > > > device		ppc0	at isa? irq 7
> > > > > device		ppbus		# Parallel port bus (required)
> > > > > device		lpt		# Printer
> > > > > device		ppi		# Parallel port interface device
> > > > >
> > > > >
> > > > > # Pseudo devices - the number indicates how many units to allocate.
> > > > > pseudo-device	loop		# Network loopback
> > > > > pseudo-device	ether		# Ethernet support
> > > > > pseudo-device	ppp	1	# Kernel PPP
> > > > > pseudo-device	tun		# Packet tunnel.
> > > > > pseudo-device	pty		# Pseudo-ttys (telnet etc)
> > > > > pseudo-device	md		# Memory "disks"
> > > > > pseudo-device	gif		# IPv6 and IPv4 tunneling
> > > > >
> > > > > # The `bpf' pseudo-device enables the Berkeley Packet Filter.
> > > > > # Be aware of the administrative consequences of enabling this!
> > > > > pseudo-device	bpf		#Berkeley packet filter
> > > > >
> > > > > # USB support
> > > > > device		uhci		# UHCI PCI->USB interface
> > > > > device		ohci		# OHCI PCI->USB interface
> > > > > device		usb		# USB Bus (required)
> > > > > device		ugen		# Generic
> > > > > device		ukbd		# Keyboard
> > > > > device		ulpt		# Printer
> > > > > device		ums		# Mouse
> > > > > device		uscanner	# Scanners
> > > > >
> > > > >
> > > > >
> > > > > On Tue, 2003-04-01 at 13:05, Marcel Stangenberger wrote:
> > > > > > > Questions:
> > > > > > > Did I break something when I made a new kernel? Why can smbfs not find a
> > > > > > > broadcast interface?
> > > > > > >
> > > > > >
> > > > > > can you provide your kernel configuration?
> > > > > >
> > > > > > Regards,
> > > > > >
> > > > > > Marcel
> > > > > > _______________________________________________
> > > > > > freebsd-questions@freebsd.org mailing list
> > > > > > http://lists.freebsd.org/mailman/listinfo/freebsd-questions
> > > > > > To unsubscribe, send any mail to "freebsd-questions-unsubscribe@freebsd.org"
> > > > >
> > > > >
> > > > > _______________________________________________
> > > > > freebsd-questions@freebsd.org mailing list
> > > > > http://lists.freebsd.org/mailman/listinfo/freebsd-questions
> > > > > To unsubscribe, send any mail to "freebsd-questions-unsubscribe@freebsd.org"
> > > > >
> > > > _______________________________________________
> > > > freebsd-questions@freebsd.org mailing list
> > > > http://lists.freebsd.org/mailman/listinfo/freebsd-questions
> > > > To unsubscribe, send any mail to "freebsd-questions-unsubscribe@freebsd.org"
> > >
> > >
> > >
> > _______________________________________________
> > freebsd-questions@freebsd.org mailing list
> > http://lists.freebsd.org/mailman/listinfo/freebsd-questions
> > To unsubscribe, send any mail to "freebsd-questions-unsubscribe@freebsd.org"
>
>
>



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.GSO.4.53.0304012034460.7268>