Date: Sat, 04 Jul 1998 22:30:46 +0200 From: Stephane Bortzmeyer <stephane@sources.org> To: aic7xxx@FreeBSD.ORG Subject: Re: Linux 2.0.34 and aic7xxx v5.0.1[49] driver Message-ID: <199807042030.WAA00495@ludwigV.sources.org> In-Reply-To: <199806280837.KAA02037@ludwigV.sources.org> (Stephane Bortzmeyer <stephane@sources.org>'s message of Sun, 28 Jun 1998 10:37:24 %2B0200)
next in thread | previous in thread | raw e-mail | index | archive | help
On Sunday 28 June 1998, at 10 h 37, the keyboard of Stephane Bortzmeyer <stephane@sources.org> wrote: > > I'm having problems with the new aic7xxx driver as shipped with > > Linux kernel version 2.0.34. As others have reported on this BTW, the problem is the same with Linux 2.0.35pre5. When the box succeed in booting, the two CD drives are not detected. dmesg : aic7xxx: Warning - detected auto-termination on controller: aic7xxx: <Adaptec AHA-294X Ultra SCSI host adapter> at PCI 11/0 aic7xxx: Please verify driver detected settings are correct. aic7xxx: If not, then please properly set the device termination aic7xxx: in the Adaptec SCSI BIOS by hitting CTRL-A when prompted aic7xxx: during machine bootup. aic7xxx: Cables present (Int-50 YES, Int-68 YES, Ext-68 NO) aic7xxx: Termination (Low OFF, High ON) (scsi0) <Adaptec AHA-294X Ultra SCSI host adapter> found at PCI 11/0 (scsi0) Wide Channel, SCSI ID=7, 16/255 SCBs (scsi0) BIOS enabled, IO Port 0xe800, IRQ 11 (scsi0) IO Memory at 0xfafff000, MMAP Memory at 0x4805000 (scsi0) Downloading sequencer code... 406 instructions downloaded scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.0.19/3.2.4 <Adaptec AHA-294X Ultra SCSI host adapter> scsi : 1 host. (scsi0:0:-1:-1) Scanning channel for devices. Vendor: WDIGTL Model: WDE4360-1807A3 Rev: 1.80 Type: Direct-Access ANSI SCSI revision: 02 Detected scsi disk sda at scsi0, channel 0, id 0, lun 0 (scsi0:0:0:0) Using wide (16 bit) transfers. (scsi0:0:0:0) Synchronous at 10.0MHz, offset 8. Vendor: WDIGTL Model: WDE4360-1807A3 Rev: 1.80 Type: Direct-Access ANSI SCSI revision: 02 Detected scsi disk sdb at scsi0, channel 0, id 1, lun 0 (scsi0:0:1:0) Using wide (16 bit) transfers. (scsi0:0:1:0) Synchronous at 10.0MHz, offset 8. scsi : detected 2 SCSI disks total. /proc/scsi/aic7xxx/0 : Adaptec AIC7xxx driver version: 5.0.19/3.2.4 Compile Options: AIC7XXX_RESET_DELAY : 15 AIC7XXX_TAGGED_QUEUEING: Adapter Support Enabled Check below to see which devices use tagged queueing AIC7XXX_PAGE_ENABLE : Enabled (This is no longer an option) AIC7XXX_PROC_STATS : Enabled Adapter Configuration: SCSI Adapter: Adaptec AHA-294X Ultra SCSI host adapter Wide Controller PCI MMAPed I/O Base: 0xfafff000 Adaptec SCSI BIOS: Enabled IRQ: 11 SCBs: Active 0, Max Active 2, Allocated 30, HW 16, Page 255 Interrupts: 6162 BIOS Control Word: 0x18b6 Adapter Control Word: 0x0019 Extended Translation: Enabled Disconnect Enable Flags: 0xffff Tag Queue Enable Flags: 0x0000 Ordered Queue Tag Flags: 0x0000 Default Tag Queue Depth: 8 Tagged Queue By Device array for aic7xxx host instance 0: {255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255} Actual queue depth per device for aic7xxx host instance 0: {1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1} To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe aic7xxx" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?199807042030.WAA00495>