Date: Thu, 27 Dec 2001 00:33:24 +1100 From: "Shaun Amy, CSIRO TIP/ATNF" <Shaun.Amy@tip.CSIRO.AU> To: freebsd-hackers@freebsd.org Cc: Shaun.Amy@tip.CSIRO.AU Subject: Re: Promise ATA100 controller: disk not recognised Message-ID: <200112261333.AAA14298@lynx.tip.CSIRO.AU> In-Reply-To: Your message of "Thu, 27 Dec 2001 00:31:34 %2B1100." <200112261331.AAA12284@lynx.tip.CSIRO.AU>
next in thread | previous in thread | raw e-mail | index | archive | help
Hi again,
As you can now see I must be needing sleep as I stupidly forgot the output
from the "boot -v" - apologies!
Thanks, Shaun.
>Season's greetings to everyone from a rather warm Sydney, Australia!
>
>This evening, I installed a new Promise UltraATA 100 TX2 controller which is
>correctly recognised at boot time. To this controller I connected a new IBN
>60 GB disk (Model: IC35L060AVER07-0). This disk is found and recognised by
>the Promise controller probe at system startup at Ultra DMA 5 so I believe
>that the cabling is correct.
>
>The problem is that although FreeBSD finds a device present, it does not
>identify the drive. The output from a "boot -v" is below in case that
>helps. My entire system was rebuilt from a "cvsup" on December 25 and the
>system is working fine otherwise it seems.
>
>Any advice or thoughts are appreciated - it could be something obvious but as
>it is after midnight here I am needing sleep!
>
>Thanks in advance.
>
>Best regards, Shaun.
---
Copyright (c) 1992-2001 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.5-PRERELEASE #0: Wed Dec 26 21:45:29 EST 2001
root@explorer.tip.CSIRO.AU:/usr/src/sys/compile/EXPLORER
Calibrating clock(s) ... TSC clock: 334084474 Hz, i8254 clock: 1193159 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz
CLK_USE_TSC_CALIBRATION not specified - using old calibration method
CPU: Pentium II/Pentium II Xeon/Celeron (334.09-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x651 Stepping = 1
Features=0x183fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR>
real memory = 268423168 (262132K bytes)
Physical memory chunk(s):
0x00001000 - 0x0009dfff, 643072 bytes (157 pages)
0x00426000 - 0x0fff4fff, 264040448 bytes (64463 pages)
avail memory = 257118208 (251092K bytes)
Programming 24 pins in IOAPIC #0
IOAPIC #0 intpin 2 -> irq 0
IOAPIC #0 intpin 16 -> irq 11
IOAPIC #0 intpin 17 -> irq 10
IOAPIC #0 intpin 19 -> irq 9
SMP: CPU0 apic_initialize():
lint0: 0x00000700 lint1: 0x00010400 TPR: 0x00000010 SVR: 0x000001ff
FreeBSD/SMP: Multiprocessor motherboard
cpu0 (BSP): apic id: 1, version: 0x00040011, at 0xfee00000
cpu1 (AP): apic id: 0, version: 0x00040011, at 0xfee00000
io0 (APIC): apic id: 2, version: 0x00170011, at 0xfec00000
bios32: Found BIOS32 Service Directory header at 0xc00f9e20
bios32: Entry = 0xf0530 (c00f0530) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0x730
pnpbios: Found PnP BIOS data at 0xc00fd2d0
pnpbios: Entry = f0000:d300 Rev = 1.0
pnpbios: OEM ID cd041
Other BIOS signatures found:
ACPI: 000f8110
Preloaded elf kernel "kernel" at 0xc03fc000.
Pentium Pro MTRR support enabled
md0: Malloc disk
Creating DISK md0
Math emulator present
SMP: CPU0 bsp_apic_configure():
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000010 SVR: 0x000001ff
pci_open(1): mode 1 addr port (0x0cf8) is 0x8000005c
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=71908086)
Using $PIR table, 7 entries at 0xc00f0d20
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82443BX (440 BX) host to PCI bridge> on motherboard
found-> vendor=0x8086, dev=0x7190, revid=0x02
class=06-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[10]: type 1, range 32, base e4000000, size 26
found-> vendor=0x8086, dev=0x7191, revid=0x02
class=06-04-00, hdrtype=0x01, mfdev=0
subordinatebus=1 secondarybus=1
found-> vendor=0x8086, dev=0x7110, revid=0x02
class=06-01-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
found-> vendor=0x8086, dev=0x7111, revid=0x01
class=01-01-80, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[20]: type 1, range 32, base 0000d800, size 4
found-> vendor=0x8086, dev=0x7112, revid=0x01
class=0c-03-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=d, irq=9
map[20]: type 1, range 32, base 0000d400, size 5
found-> vendor=0x8086, dev=0x7113, revid=0x02
class=06-80-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[90]: type 1, range 32, base 0000e800, size 4
found-> vendor=0x9005, dev=0x001f, revid=0x00
class=01-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=9
map[10]: type 1, range 32, base 0000d000, size 8
map[14]: type 1, range 64, base df000000, size 12
found-> vendor=0x8086, dev=0x1229, revid=0x05
class=02-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=9
map[10]: type 1, range 32, base e1000000, size 12
map[14]: type 1, range 32, base 0000b800, size 5
map[18]: type 1, range 32, base de800000, size 20
found-> vendor=0x105a, dev=0x4d68, revid=0x02
class=01-80-85, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=10
map[10]: type 1, range 32, base 0000b400, size 3
map[14]: type 1, range 32, base 0000b000, size 2
map[18]: type 1, range 32, base 0000a800, size 3
map[1c]: type 1, range 32, base 0000a400, size 2
map[20]: type 1, range 32, base 0000a000, size 4
map[24]: type 1, range 32, base de000000, size 14
found-> vendor=0x1000, dev=0x000f, revid=0x14
class=01-00-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
intpin=a, irq=10
map[10]: type 1, range 32, base 00009800, size 8
map[14]: type 1, range 32, base dd800000, size 8
map[18]: type 1, range 32, base dd000000, size 12
found-> vendor=0x1000, dev=0x000f, revid=0x14
class=01-00-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
intpin=a, irq=10
map[10]: type 1, range 32, base 00009400, size 8
map[14]: type 1, range 32, base dc800000, size 8
map[18]: type 1, range 32, base dc000000, size 12
pci0: <PCI bus> on pcib0
pcib1: <Intel 82443BX (440 BX) PCI-PCI (AGP) bridge> at device 1.0 on pci0
found-> vendor=0x102b, dev=0x0525, revid=0x04
class=03-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=11
map[10]: type 1, range 32, base e2000000, size 25
map[14]: type 1, range 32, base e0000000, size 14
map[18]: type 1, range 32, base df800000, size 23
pci1: <PCI bus> on pcib1
pci1: <Matrox MGA G400 AGP graphics accelerator> (vendor=0x102b, dev=0x0525) at 0.0 irq 11
isab0: <Intel 82371AB PCI to ISA bridge> at device 4.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0xd800-0xd80f at device 4.1 on pci0
ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0xd800
ata0: mask=03 status0=50 status1=01
ata0: mask=03 ostat0=50 ostat2=01
ata0-master: ATAPI probe a=14 b=eb
ata0-slave: ATAPI probe a=ff b=ff
ata0: mask=03 status0=00 status1=01
ata0-slave: ATA probe a=04 b=ff
ata0: devices=04
ata0: at 0x1f0 irq 14 on atapci0
ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0xd808
ata1: mask=00 status0=ff status1=ff
ata1: probe allocation failed
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0xd400-0xd41f irq 9 at device 4.2 on pci0
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
Timecounter "PIIX" frequency 3579545 Hz
chip1: <Intel 82371AB Power management controller> port 0xe800-0xe80f at device 4.3 on pci0
ahc0: <Adaptec aic7890/91 Ultra2 SCSI adapter> port 0xd000-0xd0ff mem 0xdf000000-0xdf000fff irq 9 at device 6.0 on pci0
ahc0: Reading SEEPROM...done.
ahc0: Manual LVD Termination
ahc0: BIOS eeprom is present
ahc0: Secondary High byte termination Enabled
ahc0: Secondary Low byte termination Enabled
ahc0: Primary Low Byte termination Enabled
ahc0: Primary High Byte termination Enabled
ahc0: Downloading Sequencer Program... 422 instructions downloaded
aic7890/91: Ultra2 Wide Channel A, SCSI Id=7, 32/255 SCBs
using shared irq9.
fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0xb800-0xb81f mem 0xde800000-0xde8fffff,0xe1000000-0xe1000fff irq 9 at device 9.0 on pci0
fxp0: using memory space register mapping
fxp0: Ethernet address 00:a0:c9:cf:19:89
fxp0: PCI IDs: 8086 1229 8086 000a 0005
fxp0: Dynamic Standby mode is disabled
inphy0: <i82555 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
bpf: fxp0 attached
atapci1: <Promise TX2 ATA100 controller> port 0xa000-0xa00f,0xa400-0xa403,0xa800-0xa807,0xb000-0xb003,0xb400-0xb407 mem 0xde000000-0xde003fff irq 10 at device 10.0 on pci0
ata-: ata2 exists, using next available unit number
ata2: iobase=0xb400 altiobase=0xb002 bmaddr=0xa000
ata2: mask=03 status0=50 status1=00
ata2: mask=03 ostat0=50 ostat2=00
ata2-master: ATAPI probe a=00 b=00
ata2-slave: ATAPI probe a=00 b=00
ata2: mask=03 status0=50 status1=00
ata2-master: ATA probe a=01 b=a5
ata2: devices=01
ata2: at 0xb400 on atapci1
ata3: iobase=0xa800 altiobase=0xa402 bmaddr=0xa008
ata3: mask=03 status0=20 status1=30
ata3: mask=03 ostat0=20 ostat2=30
ata3-master: ATAPI probe a=20 b=20
ata3-slave: ATAPI probe a=30 b=30
ata3: mask=03 status0=20 status1=30
ata3-master: ATA probe a=25 b=25
ata3-slave: ATA probe a=25 b=25
ata3: devices=00
ata3: at 0xa800 on atapci1
using shared irq10.
sym0: <875> port 0x9800-0x98ff mem 0xdd000000-0xdd000fff,0xdd800000-0xdd8000ff irq 10 at device 11.0 on pci0
sym0: Symbios NVRAM, ID 7, Fast-20, SE, parity checking
sym0: open drain IRQ line driver, using on-chip SRAM
sym0: using LOAD/STORE-based firmware.
sym0: initial SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex) 05/4e/80/01/00/24
sym0: final SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex) 05/46/80/01/08/24
sym0: Delay (GEN=11): 234 msec, 37984 KHz
sym0: Delay (GEN=11): 263 msec, 33795 KHz
sym0: Delay (GEN=11): 263 msec, 33795 KHz
sym0: enabling clock multiplier
sym0: Downloading SCSI SCRIPTS.
sym1: <875> port 0x9400-0x94ff mem 0xdc000000-0xdc000fff,0xdc800000-0xdc8000ff irq 10 at device 11.1 on pci0
sym1: Symbios NVRAM, ID 7, Fast-20, SE, parity checking
sym1: open drain IRQ line driver, using on-chip SRAM
sym1: using LOAD/STORE-based firmware.
sym1: initial SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex) 05/4e/80/01/00/24
sym1: final SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex) 05/46/80/01/08/24
sym1: Delay (GEN=11): 234 msec, 37984 KHz
sym1: Delay (GEN=11): 263 msec, 33795 KHz
sym1: Delay (GEN=11): 262 msec, 33924 KHz
sym1: enabling clock multiplier
sym1: Downloading SCSI SCRIPTS.
ata-: ata0 exists, using next available unit number
ata-: ata1 exists, using next available unit number
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xcd7ff,0xd0000-0xd07ff,0xd4000-0xd5fff on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ata4 failed to probe at port 0x1f0 irq 14 on isa0
ata5: iobase=0x0170 altiobase=0x0376 bmaddr=0x0000
ata5: mask=00 status0=ff status1=ff
ata5: probe allocation failed
ata5 failed to probe at port 0x170-0x177,0x376 irq 15 on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0047
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000
psm0: current command byte:0047
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0-00, 3 buttons
psm0: config:00000000, flags:00000000, packet size:3
psm0: syncmask:c0, syncbits:00
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0e 0f 00 00 07 80 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio0: irq maps: 0x4041 0x4051 0x4041 0x4041
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: irq maps: 0x4041 0x4049 0x4041 0x4041
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: parallel port found at 0x378
ppc0: using extended I/O port range
ppc0: ECP SPP ECP+EPP SPP
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/9 bytes threshold
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
*** ed_alloc_memory() failed! (2)
ed0 failed to probe at port 0x240-0x25f iomem 0xd4000 irq 5 on isa0
sbc0 failed to probe at port 0x220-0x22f irq 10 drq 1 flags 0x15 on isa0
isa_probe_children: probing PnP devices
SMP: enabled INTs: 1, 3, 4, 6, 7, 9, 10, 12, 14, apic_imen: 0x00ffa925
BIOS Geometries:
0:03fefe3f 0..1022=1023 cylinders, 0..254=255 heads, 1..63=63 sectors
1:03fe3f20 0..1022=1023 cylinders, 0..63=64 heads, 1..32=32 sectors
2:03fe3f20 0..1022=1023 cylinders, 0..63=64 heads, 1..32=32 sectors
3:03fefe3f 0..1022=1023 cylinders, 0..254=255 heads, 1..63=63 sectors
0 accounted for
Device configuration finished.
APIC_IO: Testing 8254 interrupt delivery
APIC_IO: routing 8254 via IOAPIC #0 intpin 2
bpf: faith0 attached
bpf: lo0 attached
SMP: AP CPU #1 Launched!
SMP: CPU1 apic_initialize():
lint0: 0x00010700 lint1: 0x00010400 TPR: 0x00000010 SVR: 0x000001ff
ata2-master: ata_command: timeout waiting for intr
ata2-master: identify failed
ata0-master: piomode=2 dmamode=-1 udmamode=-1 dmaflag=0
ata0-master: success setting PIO2 on generic chip
Creating DISK afd0
afd0: <LS-120 CSMO 05 UHD Floppy/0512C105> rewriteable drive at ata0 as master
afd0: 120MB (246528 sectors), 963 cyls, 8 heads, 32 S/T, 512 B/S
afd0: 533KB/s, PIO2
afd0: Medium: Unknown media (0x0)
Waiting 5 seconds for SCSI devices to settle
(noperiph:ahc0:0:-1:-1): SCSI bus reset delivered. 0 SCBs aborted.
(noperiph:sym0:0:-1:-1): SCSI BUS reset delivered.
sym0: enabling clock multiplier
sym0: Downloading SCSI SCRIPTS.
(noperiph:sym1:0:-1:-1): SCSI BUS reset delivered.
sym1: enabling clock multiplier
sym1: Downloading SCSI SCRIPTS.
(ahc0:A:6:0): Sending SDTR period c, offset 7f
(ahc0:A:6:0): Received SDTR period c, offset 10
Filtered to period c, offset 10
ahc0: target 6 synchronous at 20.0MHz, offset = 0x10
(ahc0:A:6:0): Sending SDTR period c, offset 10
(ahc0:A:6:0): Received SDTR period c, offset 10
Filtered to period c, offset 10
(ahc0:A:0:0): Sending WDTR 1
(ahc0:A:0:0): Received WDTR 1 filtered to 1
ahc0: target 0 using 16bit transfers
(ahc0:A:0:0): Sending SDTR period a, offset 7f
(ahc0:A:0:0): Received SDTR period a, offset f
Filtered to period a, offset f
ahc0: target 0 synchronous at 40.0MHz, offset = 0xf
(ahc0:A:1:0): Sending WDTR 1
(ahc0:A:1:0): Received WDTR 1 filtered to 1
ahc0: target 1 using 16bit transfers
(ahc0:A:1:0): Sending SDTR period c, offset 7f
(ahc0:A:1:0): Received SDTR period c, offset f
Filtered to period c, offset f
ahc0: target 1 synchronous at 20.0MHz, offset = 0xf
(ahc0:A:2:0): Sending WDTR 1
(ahc0:A:2:0): Received WDTR 1 filtered to 1
ahc0: target 2 using 16bit transfers
(ahc0:A:2:0): Sending SDTR period c, offset 7f
(ahc0:A:2:0): Received SDTR period c, offset f
Filtered to period c, offset f
ahc0: target 2 synchronous at 20.0MHz, offset = 0xf
(probe36:sym1:0:6:0): INQUIRY. CDB: 12 1 80 0 ff 0
(probe36:sym1:0:6:0): ILLEGAL REQUEST asc:24,0
(probe36:sym1:0:6:0): Invalid field in CDB
Creating DISK da0
Creating DISK da1
Creating DISK da2
sa0 at sym0 bus 0 target 4 lun 0
sa0: <SEAGATE DAT 04106-XXX 7270> Removable Sequential Access SCSI-2 device
sa0: Serial Number GS01VDJ
sa0: 7.812MB/s transfers (7.812MHz, offset 15)
Creating DISK cd0
Creating DISK cd1
pass0 at ahc0 bus 0 target 0 lun 0
pass0: <IBM DDRS-39130D DC1B> Fixed Direct Access SCSI-2 device
pass0: Serial Number RE137377
pass0: 80.000MB/s transfers (40.000MHz, offset 15, 16bit), Tagged Queueing Enabled
pass1 at ahc0 bus 0 target 1 lun 0
pass1: <IBM DCAS-34330W S65A> Fixed Direct Access SCSI-2 device
pass1: Serial Number F3TX9729
pass1: 40.000MB/s transfers (20.000MHz, offset 15, 16bit)
pass2 at ahc0 bus 0 target 2 lun 0
pass2: <IBM DCAS-34330W S65A> Fixed Direct Access SCSI-2 device
pass2: Serial Number F3TY0263
pass2: 40.000MB/s transfers (20.000MHz, offset 15, 16bit)
pass3 at ahc0 bus 0 target 6 lun 0
pass3: <TEAC CD-ROM CD-532S 1.0A> Removable CD-ROM SCSI-2 device
pass3: Serial Number \^_
pass3: 20.000MB/s transfers (20.000MHz, offset 16)
pass4 at sym0 bus 0 target 4 lun 0
pass4: <SEAGATE DAT 04106-XXX 7270> Removable Sequential Access SCSI-2 device
pass4: Serial Number GS01VDJ
pass4: 7.812MB/s transfers (7.812MHz, offset 15)
pass5 at sym1 bus 0 target 6 lun 0
pass5: <YAMAHA CRW6416S 1.0c> Removable CD-ROM SCSI-2 device
pass5: 10.000MB/s transfers (10.000MHz, offset 15)
(ahc0:A:6:0): Sending SDTR period c, offset 10
Mounting root from ufs:/dev/da0s2a
(ahc0:A:6:0): Received SDTR period c, offset 10
Filtered to period c, offset 10
(ahc0:A:6:0): Sending SDTR period c, offset 10
(ahc0:A:6:0): Received SDTR period c, offset 10
Filtered to period c, offset 10
(cd0:ahc0:0:6:0): READ CD RECORDED CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0
(cd0:ahc0:0:6:0): NOT READY asc:3a,0
(cd0:ahc0:0:6:0): Medium not present
cd0 at ahc0 bus 0 target 6 lun 0
cd0: <TEAC CD-ROM CD-532S 1.0A> Removable CD-ROM SCSI-2 device
cd0: Serial Number \^_
cd0: 20.000MB/s transfers (20.000MHz, offset 16)
cd0: Attempt to query device size failed: NOT READY, Medium not present
(cd1:sym1:0:6:0): READ CD RECORDED CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0
(cd1:sym1:0:6:0): NOT READY asc:3a,1
(cd1:sym1:0:6:0): Medium not present - tray closed
cd1 at sym1 bus 0 target 6 lun 0
cd1: <YAMAHA CRW6416S 1.0c> Removable CD-ROM SCSI-2 device
cd1: 10.000MB/s transfers (10.000MHz, offset 15)
cd1: Attempt to query device size failed: NOT READY, Medium not present - tray closed
da1 at ahc0 bus 0 target 1 lun 0
da1: <IBM DCAS-34330W S65A> Fixed Direct Access SCSI-2 device
da1: Serial Number F3TX9729
da1: 40.000MB/s transfers (20.000MHz, offset 15, 16bit)
da1: 4134MB (8467200 512 byte sectors: 255H 63S/T 527C)
da2 at ahc0 bus 0 target 2 lun 0
da2: <IBM DCAS-34330W S65A> Fixed Direct Access SCSI-2 device
da2: Serial Number F3TY0263
da2: 40.000MB/s transfers (20.000MHz, offset 15, 16bit)
da2: 4134MB (8467200 512 byte sectors: 255H 63S/T 527C)
da0 at ahc0 bus 0 target 0 lun 0
da0: <IBM DDRS-39130D DC1B> Fixed Direct Access SCSI-2 device
da0: Serial Number RE137377
da0: 80.000MB/s transfers (40.000MHz, offset 15, 16bit), Tagged Queueing Enabled
da0: 8715MB (17850000 512 byte sectors: 255H 63S/T 1111C)
da0s1: type 0x6, start 63, end = 1060289, size 1060227 : OK
da0s2: type 0xa5, start 1060290, end = 17848214, size 16787925 : OK
start_init: trying /sbin/init
da0s1: type 0x6, start 63, end = 1060289, size 1060227 : OK
da0s2: type 0xa5, start 1060290, end = 17848214, size 16787925 : OK
da0s1: type 0x6, start 63, end = 1060289, size 1060227 : OK
da0s2: type 0xa5, start 1060290, end = 17848214, size 16787925 : OK
da0s1: type 0x6, start 63, end = 1060289, size 1060227 : OK
da0s2: type 0xa5, start 1060290, end = 17848214, size 16787925 : OK
da0s1: type 0x6, start 63, end = 1060289, size 1060227 : OK
da0s2: type 0xa5, start 1060290, end = 17848214, size 16787925 : OK
da0s1: type 0x6, start 63, end = 1060289, size 1060227 : OK
da0s2: type 0xa5, start 1060290, end = 17848214, size 16787925 : OK
da0s1: type 0x6, start 63, end = 1060289, size 1060227 : OK
da0s2: type 0xa5, start 1060290, end = 17848214, size 16787925 : OK
da0s1: type 0x6, start 63, end = 1060289, size 1060227 : OK
da0s2: type 0xa5, start 1060290, end = 17848214, size 16787925 : OK
da0s1: type 0x6, start 63, end = 1060289, size 1060227 : OK
da0s2: type 0xa5, start 1060290, end = 17848214, size 16787925 : OK
da0s1: type 0x6, start 63, end = 1060289, size 1060227 : OK
da0s2: type 0xa5, start 1060290, end = 17848214, size 16787925 : OK
da0s1: type 0x6, start 63, end = 1060289, size 1060227 : OK
da0s2: type 0xa5, start 1060290, end = 17848214, size 16787925 : OK
da0s1: type 0x6, start 63, end = 1060289, size 1060227 : OK
da0s2: type 0xa5, start 1060290, end = 17848214, size 16787925 : OK
da0s1: type 0x6, start 63, end = 1060289, size 1060227 : OK
da0s2: type 0xa5, start 1060290, end = 17848214, size 16787925 : OK
da0s1: type 0x6, start 63, end = 1060289, size 1060227 : OK
da0s2: type 0xa5, start 1060290, end = 17848214, size 16787925 : OK
da0s1: type 0x6, start 63, end = 1060289, size 1060227 : OK
da0s2: type 0xa5, start 1060290, end = 17848214, size 16787925 : OK
da0s1: type 0x6, start 63, end = 1060289, size 1060227 : OK
da0s2: type 0xa5, start 1060290, end = 17848214, size 16787925 : OK
da0s1: type 0x6, start 63, end = 1060289, size 1060227 : OK
da0s2: type 0xa5, start 1060290, end = 17848214, size 16787925 : OK
da0s1: type 0x6, start 63, end = 1060289, size 1060227 : OK
da0s2: type 0xa5, start 1060290, end = 17848214, size 16787925 : OK
da0s1: type 0x6, start 63, end = 1060289, size 1060227 : OK
da0s2: type 0xa5, start 1060290, end = 17848214, size 16787925 : OK
da0s1: type 0x6, start 63, end = 1060289, size 1060227 : OK
da0s2: type 0xa5, start 1060290, end = 17848214, size 16787925 : OK
da0s1: type 0x6, start 63, end = 1060289, size 1060227 : OK
da0s2: type 0xa5, start 1060290, end = 17848214, size 16787925 : OK
da0s1: type 0x6, start 63, end = 1060289, size 1060227 : OK
da0s2: type 0xa5, start 1060290, end = 17848214, size 16787925 : OK
da0s1: type 0x6, start 63, end = 1060289, size 1060227 : OK
da0s2: type 0xa5, start 1060290, end = 17848214, size 16787925 : OK
da0s1: type 0x6, start 63, end = 1060289, size 1060227 : OK
da0s2: type 0xa5, start 1060290, end = 17848214, size 16787925 : OK
da0s1: type 0x6, start 63, end = 1060289, size 1060227 : OK
da0s2: type 0xa5, start 1060290, end = 17848214, size 16787925 : OK
da0s1: type 0x6, start 63, end = 1060289, size 1060227 : OK
da0s2: type 0xa5, start 1060290, end = 17848214, size 16787925 : OK
da0s1: type 0x6, start 63, end = 1060289, size 1060227 : OK
da0s2: type 0xa5, start 1060290, end = 17848214, size 16787925 : OK
da0s1: type 0x6, start 63, end = 1060289, size 1060227 : OK
da0s2: type 0xa5, start 1060290, end = 17848214, size 16787925 : OK
da1s1: type 0xa5, start 32, end = 8466431, size 8466400 : OK
da1s1: type 0xa5, start 32, end = 8466431, size 8466400 : OK
da1s1: type 0xa5, start 32, end = 8466431, size 8466400 : OK
da1s1: type 0xa5, start 32, end = 8466431, size 8466400 : OK
da2s1: type 0xa5, start 32, end = 8466431, size 8466400 : OK
da2s1: type 0xa5, start 32, end = 8466431, size 8466400 : OK
da2s1: type 0xa5, start 32, end = 8466431, size 8466400 : OK
da2s1: type 0xa5, start 32, end = 8466431, size 8466400 : OK
md0: invalid primary partition table: no magic
md0: invalid primary partition table: no magic
md0: invalid primary partition table: no magic
md0: invalid primary partition table: no magic
md0: invalid primary partition table: no magic
md0: invalid primary partition table: no magic
md0: invalid primary partition table: no magic
md0: invalid primary partition table: no magic
md0: invalid primary partition table: no magic
md0: invalid primary partition table: no magic
md0: invalid primary partition table: no magic
md0: invalid primary partition table: no magic
md0: invalid primary partition table: no magic
md0: invalid primary partition table: no magic
md0: invalid primary partition table: no magic
md0: invalid primary partition table: no magic
md0: invalid primary partition table: no magic
md0: invalid primary partition table: no magic
md0: invalid primary partition table: no magic
md0: invalid primary partition table: no magic
md0: invalid primary partition table: no magic
md0: invalid primary partition table: no magic
md0: invalid primary partition table: no magic
md0: invalid primary partition table: no magic
md0: invalid primary partition table: no magic
md0: invalid primary partition table: no magic
md0: invalid primary partition table: no magic
md0: invalid primary partition table: no magic
md0: invalid primary partition table: no magic
md0: invalid primary partition table: no magic
md0: invalid primary partition table: no magic
md0: invalid primary partition table: no magic
md0: invalid primary partition table: no magic
md0: invalid primary partition table: no magic
md0: invalid primary partition table: no magic
da0s1: type 0x6, start 63, end = 1060289, size 1060227 : OK
da0s2: type 0xa5, start 1060290, end = 17848214, size 16787925 : OK
splash: image decoder found: blank_saver
Linux ELF exec handler installed
/dev/vmmon: Module vmmon: registered with major=200 minor=0 tag=$Name: build-570 $
/dev/vmmon: Module vmmon: initialized
bpf: vmnet1 attached
fxp0: promiscuous mode enabled
vmnet1: promiscuous mode enabled
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-hackers" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?200112261333.AAA14298>