Date: Tue, 12 Mar 2002 10:09:16 +0900 From: NAKAJI Hiroyuki <nakaji@tutrp.tut.ac.jp> To: current@freebsd.org Subject: Re: Request for testers of ATA RAID support Message-ID: <873cz6oamb.fsf@boggy.acest.tutrp.tut.ac.jp> In-Reply-To: <200203031841.g23IfXB31877@freebsd.dk> (=?ISO-2022-JP?B?Uw==?= =?ISO-2022-JP?B?GyRCInobKEJyZW4=?= Schmidt's message of "Sun, 3 Mar 2002 19:41:33 %2B0100 (CET)") References: <200203031841.g23IfXB31877@freebsd.dk>
next in thread | previous in thread | raw e-mail | index | archive | help
>>>>> In <200203031841.g23IfXB31877@freebsd.dk>
>>>>> Soren Schmidt <sos@freebsd.dk> wrote:
SS> As some might have noticed I've done some significant work on
SS> the ATA RAID support (for Promise & Highpoint controllers)
SS> all thanks to Advanis which has made this possible.
SS> The code as it is now in -current allows for RAID1's (mirrors)
SS> to be properly handled when a disk dies, that means the
SS> system continues on the good disk and logs the loss of mirror
SS> to the console.
After this commit, I'm not sure, current kernel cannot detect ata buses on
my <HighPoint HPT370 ATA100 controller>.
Any hint is appreciated.
With new kernel on Thu Feb 28 14:07:18 JST 2002, I got following boot
message. And yesterday's kernel also has same problem, that is, atapci0
cannot be detected properly and ar disk is not available.
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.0-CURRENT #3: Thu Feb 28 14:07:18 JST 2002
root@boggy.acest.tutrp.tut.ac.jp:/usr/obj/usr/src/sys/NAKAJI
Preloaded elf kernel "/boot/kernel/kernel" at 0xc0469000.
Preloaded userconfig_script "/boot/kernel.conf" at 0xc04690a8.
Preloaded elf module "/boot/kernel/linux.ko" at 0xc04690f8.
Preloaded elf module "/boot/kernel/agp.ko" at 0xc04691a4.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc046924c.
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium 4 (1399.85-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0xf0a Stepping = 10
Features=0x3febf9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM>
real memory = 671023104 (655296K bytes)
avail memory = 647380992 (632208K bytes)
Using $PIR table, 10 entries at 0xc00fdec0
ACPI-0161: *** Error: AcpiLoadTables: Could not get RSDP, AE_NO_ACPI_TABLES
ACPI-0213: *** Error: AcpiLoadTables: Could not load tables: AE_NO_ACPI_TABLES
ACPI: table load failed: AE_NO_ACPI_TABLES
apm0: <APM BIOS> on motherboard
apm0: found APM BIOS v1.2, connected at v1.2
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> at pcibus 0 on motherboard
pci0: <PCI bus> on pcib0
agp0: <Intel 82845 host to AGP bridge> mem 0xe0000000-0xe3ffffff at device 0.0 on pci0
pcib1: <PCI-PCI bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <display, VGA> at device 0.0 (no driver attached)
pcib2: <PCI-PCI bridge> at device 30.0 on pci0
pci2: <PCI bus> on pcib2
xl0: <3Com 3c905B-TX Fast Etherlink XL> port 0x9000-0x907f mem 0xe9000000-0xe900007f irq 9 at device 1.0 on pci2
xl0: Ethernet address: 00:01:02:c2:15:af
miibus0: <MII bus> on xl0
xlphy0: <3Com internal media interface> on miibus0
xlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
ahc0: <Adaptec 2940 Ultra2 SCSI adapter (OEM)> port 0x9400-0x94ff mem 0xe9001000-0xe9001fff irq 11 at device 2.0 on pci2
aic7890/91: Ultra2 Wide Channel A, SCSI Id=7, 32/255 SCBs
atapci0: <HighPoint HPT370 ATA100 controller> port 0xa800-0xa8ff,0xa400-0xa403,0xa000-0xa007,0x9c00-0x9c03,0x9800-0x9807 irq 5 at device 5.0 on pci2
pcib2: device atapci0 requested unsupported I/O range 0x0-0x9c00 (decoding 0x9000-0xafff)
pcib2: device atapci0 requested unsupported I/O range 0x0-0xa400 (decoding 0x9000-0xafff)
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci1: <Intel ICH2 ATA100 controller> port 0xf000-0xf00f at device 31.1 on pci0
ata0: at 0x1f0 irq 14 on atapci1
ata1: at 0x170 irq 15 on atapci1
pci0: <serial bus, USB> at device 31.2 (no driver attached)
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
pci0: <serial bus, USB> at device 31.4 (no driver attached)
pcm0: <Intel 82801BA (ICH2)> port 0xc000-0xc03f,0xbc00-0xbcff irq 11 at device 31.5 on pci0
orm0: <Option ROMs> at iomem 0xd0000-0xd57ff,0xc0000-0xcffff on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x64,0x60 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: failed to get data.
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model IntelliMouse, device ID 3
fdc0: <enhanced floppy controller (i82077, NE72065 or clone)> at port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/9 bytes threshold
ppbus0: IEEE1284 device found /NIBBLE/ECP/ECP_RLE
Probing for PnP devices on ppbus0:
ppbus0: <EPSON LP-8400PS3> PRINTER POSTSCRIPT
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
ppc1: cannot reserve I/O port range
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
ad0: 2441MB <WDC AC32500H> [4960/16/63] at ata0-master WDMA2
ad1: 14655MB <Maxtor 31536U2> [29777/16/63] at ata0-slave UDMA66
ad3: 9765MB <FUJITSU MPC3102AT E> [19841/16/63] at ata1-slave UDMA33
acd0: CDROM <TOSHIBA CD-ROM XM-5602B> at ata1-master PIO3
Waiting 15 seconds for SCSI devices to settle
Mounting root from ufs:/dev/da0s1a
da0 at ahc0 bus 0 target 0 lun 0
da0: <IBM DPES-31080 S31Q> Fixed Direct Access SCSI-2 device
da0: 10.000MB/s transfers (10.000MHz, offset 15), Tagged Queueing Enabled
da0: 1034MB (2118144 512 byte sectors: 255H 63S/T 131C)
da1 at ahc0 bus 0 target 4 lun 0
da1: <IBM DPSS-318350N S96H> Fixed Direct Access SCSI-3 device
da1: 80.000MB/s transfers (40.000MHz, offset 63, 16bit), Tagged Queueing Enabled
da1: 17501MB (35843670 512 byte sectors: 255H 63S/T 2231C)
da2 at ahc0 bus 0 target 6 lun 0
da2: <QUANTUM FIREBALL SE2.1S PJ09> Fixed Direct Access SCSI-2 device
da2: 20.000MB/s transfers (20.000MHz, offset 15), Tagged Queueing Enabled
da2: 2051MB (4201304 512 byte sectors: 255H 63S/T 261C)
With older kernel (without acpi.ko),
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.0-CURRENT #2: Fri Feb 8 14:40:03 JST 2002
root@boggy.acest.tutrp.tut.ac.jp:/usr/obj/usr/src/sys/NAKAJI
Preloaded elf kernel "/boot/kernel/kernel" at 0xc044c000.
Preloaded userconfig_script "/boot/kernel.conf" at 0xc044c0a8.
Preloaded elf module "/boot/kernel/linux.ko" at 0xc044c0f8.
Preloaded elf module "/boot/kernel/agp.ko" at 0xc044c1a4.
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium 4 (1399.85-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0xf0a Stepping = 10
Features=0x3febf9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM>
real memory = 671023104 (655296K bytes)
avail memory = 647507968 (632332K bytes)
Using $PIR table, 10 entries at 0xc00fdec0
apm0: <APM BIOS> on motherboard
apm0: found APM BIOS v1.2, connected at v1.2
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> at pcibus 0 on motherboard
pci0: <PCI bus> on pcib0
agp0: <Intel 82845 host to AGP bridge> mem 0xe0000000-0xe3ffffff at device 0.0 on pci0
pcib1: <PCI-PCI bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <display, VGA> at device 0.0 (no driver attached)
pcib2: <PCI-PCI bridge> at device 30.0 on pci0
pci2: <PCI bus> on pcib2
xl0: <3Com 3c905B-TX Fast Etherlink XL> port 0x9000-0x907f mem 0xe9000000-0xe900007f irq 9 at device 1.0 on pci2
xl0: Ethernet address: 00:01:02:c2:15:af
miibus0: <MII bus> on xl0
xlphy0: <3Com internal media interface> on miibus0
xlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
ahc0: <Adaptec 2940 Ultra2 SCSI adapter (OEM)> port 0x9400-0x94ff mem 0xe9001000-0xe9001fff irq 11 at device 2.0 on pci2
aic7890/91: Ultra2 Wide Channel A, SCSI Id=7, 32/255 SCBs
atapci0: <HighPoint HPT370 ATA100 controller> port 0xa800-0xa8ff,0xa400-0xa403,0xa000-0xa007,0x9c00-0x9c03,0x9800-0x9807 irq 5 at device 5.0 on pci2
ata2: at 0x9800 on atapci0
ata3: at 0xa000 on atapci0
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci1: <Intel ICH2 ATA100 controller> port 0xf000-0xf00f at device 31.1 on pci0
ata0: at 0x1f0 irq 14 on atapci1
ata1: at 0x170 irq 15 on atapci1
uhci0: <Intel 82801BA/BAM (ICH2) USB controller USB-A> port 0xb000-0xb01f irq 11 at device 31.2 on pci0
usb0: <Intel 82801BA/BAM (ICH2) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
uhci1: <Intel 82801BA/BAM (ICH2) USB controller USB-B> port 0xb800-0xb81f irq 5 at device 31.4 on pci0
usb1: <Intel 82801BA/BAM (ICH2) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
pcm0: <Intel 82801BA (ICH2)> port 0xc000-0xc03f,0xbc00-0xbcff irq 11 at device 31.5 on pci0
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
orm0: <Option ROMs> at iomem 0xd0000-0xd57ff,0xc0000-0xcffff on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x64,0x60 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: failed to get data.
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model IntelliMouse, device ID 3
fdc0: <enhanced floppy controller (i82077, NE72065 or clone)> at port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/9 bytes threshold
ppbus0: IEEE1284 device found /NIBBLE/ECP/ECP_RLE
Probing for PnP devices on ppbus0:
ppbus0: <EPSON LP-8400PS3> PRINTER POSTSCRIPT
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
ppc1: cannot reserve I/O port range
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
unknown: <PNP0303> can't assign resources
unknown: <PNP0a03> can't assign resources
unknown: <PNP0f13> can't assign resources
unknown: <PNP0501> can't assign resources
unknown: <PNP0700> can't assign resources
unknown: <PNP0401> can't assign resources
unknown: <PNP0501> can't assign resources
ad0: 2441MB <WDC AC32500H> [4960/16/63] at ata0-master WDMA2
ad1: 14655MB <Maxtor 31536U2> [29777/16/63] at ata0-slave UDMA66
ad3: 9765MB <FUJITSU MPC3102AT E> [19841/16/63] at ata1-slave UDMA33
ar0: 43979MB <ATA RAID1 array> [5606/255/63] status: READY subdisks:
0 READY ad4: 43979MB <IBM-DTLA-307045> [89355/16/63] at ata2-master UDMA100
1 READY ad6: 43979MB <IBM-DTLA-307045> [89355/16/63] at ata3-master UDMA100
acd0: CDROM <TOSHIBA CD-ROM XM-5602B> at ata1-master PIO3
Waiting 15 seconds for SCSI devices to settle
Mounting root from ufs:/dev/da0s1a
da0 at ahc0 bus 0 target 0 lun 0
da0: <IBM DPES-31080 S31Q> Fixed Direct Access SCSI-2 device
da0: 10.000MB/s transfers (10.000MHz, offset 15), Tagged Queueing Enabled
da0: 1034MB (2118144 512 byte sectors: 255H 63S/T 131C)
da1 at ahc0 bus 0 target 4 lun 0
da1: <IBM DPSS-318350N S96H> Fixed Direct Access SCSI-3 device
da1: 80.000MB/s transfers (40.000MHz, offset 63, 16bit), Tagged Queueing Enabled
da1: 17501MB (35843670 512 byte sectors: 255H 63S/T 2231C)
da2 at ahc0 bus 0 target 6 lun 0
da2: <QUANTUM FIREBALL SE2.1S PJ09> Fixed Direct Access SCSI-2 device
da2: 20.000MB/s transfers (20.000MHz, offset 15), Tagged Queueing Enabled
da2: 2051MB (4201304 512 byte sectors: 255H 63S/T 261C)
--
NAKAJI Hiroyuki
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-current" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?873cz6oamb.fsf>