Date: Sat, 21 Sep 2002 18:55:49 +0200 From: Arnvid Karstad <arnvid@karstad.org> To: freebsd-stable@freebsd.org Subject: Re: install cd boot problems?! Message-ID: <20020921185352.7AB0.ARNVID@karstad.org> In-Reply-To: <20020921184657.7AAD.ARNVID@karstad.org> References: <20020921182404.7AA1.ARNVID@karstad.org> <20020921184657.7AAD.ARNVID@karstad.org>
next in thread | previous in thread | raw e-mail | index | archive | help
Bios Geometrics: 0 \ 1 | 2 | disk info.. snipped away bcoz it's a bit to write down to paper. 3 / 0 accounted for Device configuration finished bpf: lo0 attached bpf: sl0 attached Waiting 15 seconds for scsi devices to settle (noperiph:ahc0:0:-1:-1): SCSI bus reset delieverd. 0 SCBs aborted. On Sat, 21 Sep 2002 18:47:02 +0200 - Arnvid Karstad <arnvid@karstad.org> wrote: > When booting with boot -v -s as someone nicely suggested.. this is the > last line: > > (noperiph:ahc0:0:-1:-1): SCSI bus reset delieverd. 0 SCBs aborted. > > > On Sat, 21 Sep 2002 18:26:57 +0200 - Arnvid Karstad <arnvid@karstad.org> wrote: > > > Hiya, > > > > > > Trying to install FreeBSD on one of the older dual cpu pentium pro > > machines we have and it always seem to freeze up around when it's > > supposed to wait 15 seconds for the scsi devices to settle. > > > > Tried to boot both 4.5 and 4.6.2 release cd's boot no luck. Linux boots > > and shows the scsi subsystem being: > > > > SCSI subsystem driver Revision: 1.00 > > scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.1.13 > > <Adaptec aic7880 Ultra SCSI adapter> > > aic7880: Ultra Wide Channel A, SCSI Id=7, 16/255 SCBs > > > > Vendor: COMPAQPC Model: DORS-32160 Rev: WA8B > > Type: Direct-Access ANSI SCSI revision: 02 > > (scsi0:A:0): 20.000MB/s transfers (20.000MHz, offset 15) > > Vendor: QUANTUM Model: FIREBALL SE8.4S Rev: PJ0A > > Type: Direct-Access ANSI SCSI revision: 02 > > (scsi0:A:1): 20.000MB/s transfers (20.000MHz, offset 15) > > Vendor: QUANTUM Model: FIREBALL_TM3200S Rev: 300X > > Type: Direct-Access ANSI SCSI revision: 02 > > (scsi0:A:2): 20.000MB/s transfers (20.000MHz, offset 15) > > Vendor: IBM Model: CDRM00203 !K Rev: 8B08 > > Type: CD-ROM ANSI SCSI revision: 02 > > (scsi0:A:6): 10.000MB/s transfers (10.000MHz, offset 15) > > scsi0:0:0:0: Tagged Queuing enabled. Depth 253 > > scsi0:0:1:0: Tagged Queuing enabled. Depth 253 > > scsi0:0:2:0: Tagged Queuing enabled. Depth 253 > > Detected scsi disk sda at scsi0, channel 0, id 0, lun 0 > > Detected scsi disk sdb at scsi0, channel 0, id 1, lun 0 > > Detected scsi disk sdc at scsi0, channel 0, id 2, lun 0 > > SCSI device sda: 4110000 512-byte hdwr sectors (2104 MB) > > Partition check: > > sda: sda1 > > SCSI device sdb: 16777215 512-byte hdwr sectors (8590 MB) > > sdb: sdb1 sdb2 sdb3 > > SCSI device sdc: 6281856 512-byte hdwr sectors (3216 MB) > > sdc: sdc1 sdc2 sdc3 > > Detected scsi CD-ROM sr0 at scsi0, channel 0, id 6, lun 0 > > > > > > Anyone got any good ideas? > > > > > > Mvh/Best regards, > > > > Arnvid L. Karstad > > > > > > > > To Unsubscribe: send mail to majordomo@FreeBSD.org > > with "unsubscribe freebsd-stable" in the body of the message > > > Mvh/Best regards, > > Arnvid L. Karstad > > Mvh/Best regards, Arnvid L. Karstad To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-stable" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20020921185352.7AB0.ARNVID>