Date: Sun, 18 Apr 2004 00:59:32 +0100 From: "Markie" <mark.cullen@dsl.pipex.com> To: <gerard-seibert@rcn.com>, "FreeBSD Questions" <freebsd-questions@freebsd.org> Subject: Re: Configuring Compaq Wireless Optical Wheel Mouse Message-ID: <000e01c424d8$0886e2d0$f700000a@ape> References: <200404171928.38234.gerard-seibert@rcn.com>
next in thread | previous in thread | raw e-mail | index | archive | help
Try /dev/ums0 :) ----- Original Message ----- From: "Gerard Seibert" <gerard-seibert@rcn.com> To: "FreeBSD Questions" <freebsd-questions@freebsd.org> Sent: Sunday, April 18, 2004 12:28 AM Subject: Configuring Compaq Wireless Optical Wheel Mouse > I am trying to configure a COMPAQ Wirless Optical Mouse to work with KDE on > FreeBSD 5.2.1. so far I have not been very successful. This is a USB mouse. > > I can get the mouse pointer to work in FreeBSD and KDE without any problem. > However, I can not get the wheel to work anywhere. > > This is the output of the 'dmesg.today' file: > > root@dhcppc3 /var/log $ cat dmesg.today > Copyright (c) 1992-2004 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > FreeBSD 5.2.1-RELEASE #0: Mon Feb 23 20:45:55 GMT 2004 > root@wv1u.btc.adaptec.com:/usr/obj/usr/src/sys/GENERIC > Preloaded elf kernel "/boot/kernel/kernel" at 0xc0a0e000.# Identifier and > driver > Preloaded elf module "/boot/kernel/snd_pcm.ko" at 0xc0a0e0cc. > Preloaded elf module "/boot/kernel/sn# Identifier and driver > d_ess.ko" at 0xc0a0e178. > Preloaded elf module "/boot/kernel/snd_sbc.ko" at 0xc0a0e224. > Timecounter "i8254" frequency 1193182 Hz quality 0 > CPU: Pentium II/Pentium II Xeon/Celeron (397.33-MHz 686-class CPU) > Origin = "GenuineIntel" Id = 0x651 Stepping = 1 > Features=0x183f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV, PAT,PSE36,MMX,FXSR> > real memory = 402653184 (384 MB) > avail memory = 381427712 (363 MB) > Pentium Pro MTRR support enabled > npx0: [FAST] > npx0: <math processor> on motherboard > npx0: INT 16 interface > pcibios: BIOS version 2.10 > Using $PIR table, 5 entries at 0xc00fa040 > pcib0: <Intel 82443BX (440 BX) host to PCI bridge> at pcibus 0 on motherboard > pci0: <PCI bus> on pcib0 > pci_cfgintr: 0:4 INTA BIOS irq 11 > pci_cfgintr: 0:20 INTD BIOS irq 11 > agp0: <Intel 82443BX (440 BX) host to PCI bridge> mem 0x44000000-0x47ffffff at > device 0.0 on pci0 > pcib1: <PCI-PCI bridge> at device 1.0 on pci0 > pci1: <PCI bus> on pcib1 > pci_cfgintr: 0:1 INTA routed to irq 4 > pcib1: slot 0 INTA is routed to irq 4 > pci1: <display, VGA> at device 0.0 (no driver attached) > rl0: <RealTek 8139 10/100BaseTX> port 0x2400-0x24ff mem 0x41100000-0x411000ff > irq 11 at device 4.0 on pci0 > rl0: Ethernet address: 00:50:ba:40:6d:e1 > miibus0: <MII bus> on rl0 > rlphy0: <RealTek internal media interface> on miibus0 > rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto > isab0: <PCI-ISA bridge> at device 20.0 on pci0 > isa0: <ISA bus> on isab0 > atapci0: <Intel PIIX4 UDMA33 controller> port 0x20a0-0x20af at device 20.1 on > pci0 > ata0: at 0x1f0 irq 14 on atapci0 > ata0: [MPSAFE] > ata1: at 0x170 irq 15 on atapci0 > ata1: [MPSAFE] > uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0x2080-0x209f irq 11 at > device 20.2 on pci0 > usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0 > usb0: USB revision 1.0 > uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub0: 2 ports with 2 removable, self powered > ums0: MOUSE SYSTEM U+P RF Mouse Receiver, rev 1.10/0.00, addr 2, iclass 3/1 > ums0: 5 buttons and Z dir. > piix0: <PIIX Timecounter> port 0xee80-0xee8f at device 20.3 on pci0 > Timecounter "PIIX" frequency 3579545 Hz quality 0 > orm0: <Option ROM> at iomem 0xc0000-0xcffff on isa0 > pmtimer0 on isa0 > atkbdc0: <Keyboard controller (i8042)> at port 0x64,0x60 on isa0 > atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 > kbd0 at atkbd0 > fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> at port > 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on isa0 > fdc0: FIFO enabled, 8 bytes threshold > fd0: <1440-KB 3.5" drive> on fdc0 drive 0 > ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0 > ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode > ppc0: FIFO with 16/16/15 bytes threshold > ppbus0: <Parallel port bus> on ppc0 > plip0: <PLIP network interface> on ppbus0 > lpt0: <Printer> on ppbus0 > lpt0: Interrupt-driven port > ppi0: <Parallel I/O> on ppbus0 > sc0: <System console> at flags 0x100 on isa0 > sc0: VGA <16 virtual consoles, flags=0x300> > sio0: configured irq 4 not in bitmap of probed irqs 0 > sio0: port may not be enabled > sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 > sio0: type 16550A > sio1: configured irq 3 not in bitmap of probed irqs 0 > sio1: port may not be enabled > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 > sio4: <U.S. Robotics 56K Voice INT> at port 0x2f8-0x2ff irq 3 on isa0 > sio4: type 16550A > unknown: <PNP0401> can't assign resources (port) > unknown: <PNP0501> can't assign resources (port) > sbc0: <ESS ES1869 (Compaq OEM)> at port 0x330-0x331,0x388-0x38b,0x220-0x22f > irq 5 drq 3,1 on isa0 > pcm0: <ESS 18xx DSP> on sbc0 > unknown: <PNP0700> can't assign resources (port) > unknown: <PNP0303> can't assign resources (port) > unknown: <PNP0c02> can't assign resources (port) > Timecounter "TSC" frequency 397331698 Hz quality 800 > Timecounters tick every 10.000 msec > GEOM: create disk ad0 dp=0xc3b55260 > ad0: 7665MB <QUANTUM Bigfoot TX8.0AT> [15574/16/63] at ata0-master UDMA33 > acd0: DVDROM <COMPAQ DVD-ROM GD-2000> at ata1-master WDMA2 > GEOM: create disk afd0 dp=0xc3b5446c > afd0: REMOVABLE <IOMEGA ZIP 100 ATAPI> at ata1-slave PIO0 > Mounting root from ufs:/dev/ad0s1a > > This is my 'rc.conf' file: > > blanktime="3600" > #hostname="dhcppc3.cable.rcn.com" > hostname="" > ifconfig_rl0="DHCP" > linux_enable="YES" > lpd_enable="YES" > named_enable="NO" > saver="logo" > sendmail_enable="NONE" > sshd_enable="YES" > usbd_enable="YES" > ntpd_enable="YES" > clear_tmp_enabled="YES" > moused_flags="z 6 7" > moused_port="/dev/usb0" > moused_type="auto" > moused_enable="YES" > > Finally, here the the mouse section from the 'XF86Config' file: > > # Identifier and driver > > Identifier "Mouse1" > Driver "mouse" > Option "Protoco" "Auto" > Option "Device" "/dev/sysmouse" > Option "Buttons" "7" > Option "ZAxisMapping" "6 7" > > I might add that I receive an error message upon boot up that the 'moused' was > not supplied with the correct port. I have tried every port I can think of, > and it sill gives me an error. > > I would really appreciate any help someone might be able to afford me. > > Thanks! > > Gerard Seibert > gerard-seibert@rcn.com > _______________________________________________ > freebsd-questions@freebsd.org mailing list > http://lists.freebsd.org/mailman/listinfo/freebsd-questions > To unsubscribe, send any mail to "freebsd-questions-unsubscribe@freebsd.org"
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?000e01c424d8$0886e2d0$f700000a>