Date: Sat, 22 May 2004 23:02:56 -0700 (PDT) From: Don Lewis <truckman@FreeBSD.org> To: imp@bsdimp.com Cc: current@FreeBSD.org Subject: Re: an0 turns on after suspend/resume Message-ID: <200405230603.i4N62u7E035421@gw.catspoiler.org> In-Reply-To: <20040522.232717.74547525.imp@bsdimp.com>
next in thread | previous in thread | raw e-mail | index | archive | help
On 22 May, M. Warner Losh wrote: > In message: <200405222346.i4MNkp7E035028@gw.catspoiler.org> > Don Lewis <truckman@freebsd.org> writes: > : My Thinkpad R40 has a built-in an WiFi mini-PCI card. I seldom use it, > : so I just leave it unconfigured, which seems to leave it powered off. If > : I suspend it to S3 and then resume, the broadcast antenna LED under the > : display turns on, indicating that the card is active. I also see four > : messages on the console "an0: unknown RID: 0". > > dmesg? Here's /var/log/messages starting with the initial boot and through the suspend and resume. ACPI_DEBUG is enabled, but not bootverbose. BTW, it also locks up when I switch back to X11 after resume. Seems to be related to the irq 11 storm. Irq 11 is used by uhci0, fwohci0, fxp0, and drm0. The the top part of the display is corrupted after I switch back, and the machine locks and blanks the screen within a few seconds. I don't get the message about the irq 11 storm and the machine stays up if I leave the console switched to a text vty. This is the first time I've played with suspend and resume in a few months. It has never worked correctly. May 22 14:48:20 hairball syslogd: kernel boot file is /boot/kernel/kernel May 22 14:48:20 hairball kernel: Copyright (c) 1992-2004 The FreeBSD Project. May 22 14:48:20 hairball kernel: Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 May 22 14:48:20 hairball kernel: The Regents of the University of California. All rights reserved. May 22 14:48:20 hairball kernel: FreeBSD 5.2-CURRENT #167: Sat May 22 03:46:17 PDT 2004 May 22 14:48:20 hairball kernel: dl@hairball.catspoiler.org:/usr/obj/usr/src/sys/ACPI_DEBUG May 22 14:48:20 hairball kernel: WARNING: WITNESS option enabled, expect reduced performance. May 22 14:48:20 hairball kernel: Preloaded elf kernel "/boot/kernel/kernel" at 0xc0a15000. May 22 14:48:20 hairball kernel: Preloaded elf module "/boot/kernel/snd_ich.ko" at 0xc0a1526c. May 22 14:48:20 hairball kernel: Preloaded elf module "/boot/kernel/snd_pcm.ko" at 0xc0a15318. May 22 14:48:20 hairball kernel: Preloaded elf module "/boot/kernel/acpi_video.ko" at 0xc0a153c4. May 22 14:48:20 hairball kernel: Preloaded elf module "/boot/kernel/acpi.ko" at 0xc0a15474. May 22 14:48:20 hairball kernel: Timecounter "i8254" frequency 1193182 Hz quality 0 May 22 14:48:20 hairball kernel: CPU: Intel(R) Pentium(R) M processor 1500MHz (1498.73-MHz 686-class CPU) May 22 14:48:20 hairball kernel: Origin = "GenuineIntel" Id = 0x695 Stepping = 5 May 22 14:48:20 hairball kernel: Features=0xa7e9f9bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,TM,PBE> May 22 14:48:20 hairball kernel: real memory = 536215552 (511 MB) May 22 14:48:20 hairball kernel: avail memory = 514977792 (491 MB) May 22 14:48:20 hairball kernel: random: <entropy source, Software, Yarrow> May 22 14:48:20 hairball kernel: Pentium Pro MTRR support enabled May 22 14:48:20 hairball kernel: npx0: [FAST] May 22 14:48:20 hairball kernel: npx0: <math processor> on motherboard May 22 14:48:20 hairball kernel: npx0: INT 16 interface May 22 14:48:20 hairball kernel: acpi0: <IBM TP-1P> on motherboard May 22 14:48:20 hairball kernel: acpi0: [GIANT-LOCKED] May 22 14:48:20 hairball kernel: acpi_ec0: <Embedded Controller: GPE 0x1c, ECDT> port 0x66,0x62 on acpi0 May 22 14:48:20 hairball kernel: pcibios: BIOS version 2.10 May 22 14:48:20 hairball kernel: acpi0: Power Button (fixed) May 22 14:48:20 hairball kernel: Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 May 22 14:48:20 hairball kernel: acpi_ec0: info: new max delay is 11000 us May 22 14:48:20 hairball kernel: acpi_ec0: info: new max delay is 101000 us May 22 14:48:20 hairball kernel: acpi_ec0: EcRead: Failed waiting for EC to send data. May 22 14:48:20 hairball kernel: evregion-0440: *** Error: Handler for [EmbeddedControl] returned AE_NO_HARDWARE_RESPONSE May 22 14:48:20 hairball kernel: May 22 14:48:20 hairball kernel: **** Exception AE_NO_HARDWARE_RESPONSE during execution of method [\_SB_.PCI0.LPC_.EC__.AC__._PSR] (Node 0xc4448428) May 22 14:48:20 hairball kernel: May 22 14:48:20 hairball kernel: Method Execution Stack: May 22 14:48:20 hairball kernel: Method [_PSR] executing: 0 # a4 Return ( 1 # 2d HPAC) May 22 14:48:20 hairball kernel: Method [_CST] executing: Call to method [\_SB_.PCI0.LPC_.EC__.AC__._PSR] (Node 0xc4448428) May 22 14:48:20 hairball kernel: May 22 14:48:20 hairball kernel: Local Variables for method [_PSR]: May 22 14:48:20 hairball kernel: Local0: 0 <NullObj> May 22 14:48:20 hairball kernel: Local1: 0 <NullObj> May 22 14:48:20 hairball kernel: Local2: 0 <NullObj> May 22 14:48:20 hairball kernel: Local3: 0 <NullObj> May 22 14:48:20 hairball kernel: Local4: 0 <NullObj> May 22 14:48:20 hairball kernel: Local5: 0 <NullObj> May 22 14:48:20 hairball kernel: Local6: 0 <NullObj> May 22 14:48:20 hairball kernel: Local7: 0 <NullObj> May 22 14:48:20 hairball kernel: May 22 14:48:20 hairball kernel: Arguments for Method [_PSR]: (0 arguments defined, max concurrency = ff) May 22 14:48:20 hairball kernel: Arg0: 0 <NullObj> May 22 14:48:20 hairball kernel: Arg1: 0 <NullObj> May 22 14:48:20 hairball kernel: Arg2: 0 <NullObj> May 22 14:48:20 hairball kernel: Arg3: 0 <NullObj> May 22 14:48:20 hairball kernel: Arg4: 0 <NullObj> May 22 14:48:20 hairball kernel: Arg5: 0 <NullObj> May 22 14:48:20 hairball kernel: Arg6: 0 <NullObj> May 22 14:48:20 hairball kernel: May 22 14:48:20 hairball kernel: psparse-1303: *** Error: Method execution failed [\_SB_.PCI0.LPC_.EC__.AC__._PSR] (Node 0xc4448428), AE_NO_HARDWARE_RESPONSE May 22 14:48:20 hairball kernel: psparse-1303: *** Error: Method execution failed [\_PR_.CPU_._CST] (Node 0xc4431328), AE_NO_HARDWARE_RESPONSE May 22 14:48:20 hairball kernel: cpu0: <ACPI CPU (3 Cx states)> on acpi0 May 22 14:48:20 hairball kernel: acpi_tz0: <Thermal Zone> on acpi0 May 22 14:48:20 hairball kernel: acpi_lid0: <Control Method Lid Switch> on acpi0 May 22 14:48:20 hairball kernel: acpi_button0: <Sleep Button> on acpi0 May 22 14:48:20 hairball kernel: pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 May 22 14:48:20 hairball kernel: pci0: <ACPI PCI bus> on pcib0 May 22 14:48:20 hairball kernel: pcib0: slot 29 INTA is routed to irq 11 May 22 14:48:20 hairball kernel: pcib0: slot 29 INTB is routed to irq 5 May 22 14:48:20 hairball kernel: pcib0: slot 29 INTC is routed to irq 9 May 22 14:48:20 hairball kernel: pcib0: slot 29 INTD is routed to irq 11 May 22 14:48:20 hairball kernel: pcib0: slot 31 INTB is routed to irq 10 May 22 14:48:20 hairball last message repeated 2 times May 22 14:48:20 hairball kernel: agp0: <Intel 82855 host to AGP bridge> mem 0xd0000000-0xdfffffff at device 0.0 on pci0 May 22 14:48:20 hairball kernel: pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0 May 22 14:48:20 hairball kernel: pci1: <ACPI PCI bus> on pcib1 May 22 14:48:20 hairball kernel: pcib1: slot 0 INTA is routed to irq 11 May 22 14:48:20 hairball kernel: pci1: <display, VGA> at device 0.0 (no driver attached) May 22 14:48:20 hairball kernel: uhci0: <Intel 82801DB (ICH4) USB controller USB-A> port 0x1800-0x181f irq 11 at device 29.0 on pci0 May 22 14:48:20 hairball kernel: uhci0: [GIANT-LOCKED] May 22 14:48:20 hairball kernel: usb0: <Intel 82801DB (ICH4) USB controller USB-A> on uhci0 May 22 14:48:20 hairball kernel: usb0: USB revision 1.0 May 22 14:48:20 hairball kernel: uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 May 22 14:48:20 hairball kernel: uhub0: 2 ports with 2 removable, self powered May 22 14:48:20 hairball kernel: uhub1: IBM Corporation product 0x4482, class 9/0, rev 2.00/0.00, addr 2 May 22 14:48:20 hairball kernel: uhub1: 4 ports with 4 removable, self powered May 22 14:48:20 hairball kernel: uhci1: <Intel 82801DB (ICH4) USB controller USB-B> port 0x1820-0x183f irq 5 at device 29.1 on pci0 May 22 14:48:20 hairball kernel: uhci1: [GIANT-LOCKED] May 22 14:48:20 hairball kernel: usb1: <Intel 82801DB (ICH4) USB controller USB-B> on uhci1 May 22 14:48:20 hairball kernel: usb1: USB revision 1.0 May 22 14:48:20 hairball kernel: uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 May 22 14:48:20 hairball kernel: uhub2: 2 ports with 2 removable, self powered May 22 14:48:20 hairball kernel: uhci2: <Intel 82801DB (ICH4) USB controller USB-C> port 0x1840-0x185f irq 9 at device 29.2 on pci0 May 22 14:48:20 hairball kernel: uhci2: [GIANT-LOCKED] May 22 14:48:20 hairball kernel: usb2: <Intel 82801DB (ICH4) USB controller USB-C> on uhci2 May 22 14:48:20 hairball kernel: usb2: USB revision 1.0 May 22 14:48:20 hairball kernel: uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 May 22 14:48:20 hairball kernel: uhub3: 2 ports with 2 removable, self powered May 22 14:48:20 hairball kernel: pci0: <serial bus, USB> at device 29.7 (no driver attached) May 22 14:48:20 hairball kernel: pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0 May 22 14:48:20 hairball kernel: pci2: <ACPI PCI bus> on pcib2 May 22 14:48:20 hairball kernel: pcib2: slot 0 INTA is routed to irq 5 May 22 14:48:20 hairball kernel: pcib2: slot 2 INTA is routed to irq 9 May 22 14:48:20 hairball kernel: pcib2: slot 7 INTA is routed to irq 11 May 22 14:48:20 hairball kernel: pcib2: slot 8 INTA is routed to irq 11 May 22 14:48:20 hairball kernel: cbb0: <TI1510 PCI-CardBus Bridge> irq 5 at device 0.0 on pci2 May 22 14:48:20 hairball kernel: cardbus0: <CardBus bus> on cbb0 May 22 14:48:20 hairball kernel: pccard0: <16-bit PCCard bus> on cbb0 May 22 14:48:20 hairball kernel: an0: <Cisco Aironet MPI350> port 0x8000-0x80ff mem 0xc0400000-0xc07fffff,0xc0200000-0xc0203fff irq 9 at device 2.0 on pci2 May 22 14:48:20 hairball kernel: an0: got RSSI <-> dBM map May 22 14:48:20 hairball kernel: an0: supported rates: 1Mbps 2Mbps 5.5Mbps 11Mbps May 22 14:48:20 hairball kernel: an0: Ethernet address: 00:02:8a:a3:3c:a8 May 22 14:48:20 hairball kernel: an0: [GIANT-LOCKED] May 22 14:48:20 hairball kernel: fwohci0: vendor=104c, dev=8026 May 22 14:48:20 hairball kernel: fwohci0: <1394 Open Host Controller Interface> mem 0xc0204000-0xc0207fff,0xc0209000-0xc02097ff irq 11 at device 7.0 on pci2 May 22 14:48:20 hairball kernel: fwohci0: [GIANT-LOCKED] May 22 14:48:20 hairball kernel: fwohci0: OHCI version 1.10 (ROM=0) May 22 14:48:20 hairball kernel: fwohci0: No. of Isochronous channels is 4. May 22 14:48:20 hairball kernel: fwohci0: EUI64 00:06:1b:00:20:09:dc:c3 May 22 14:48:20 hairball kernel: fwohci0: Phy 1394a available S400, 1 ports. May 22 14:48:20 hairball kernel: fwohci0: Link S400, max_rec 2048 bytes. May 22 14:48:20 hairball kernel: firewire0: <IEEE1394(FireWire) bus> on fwohci0 May 22 14:48:20 hairball kernel: fwe0: <Ethernet over FireWire> on firewire0 May 22 14:48:20 hairball kernel: if_fwe0: Fake Ethernet address: 02:06:1b:09:dc:c3 May 22 14:48:20 hairball kernel: fwe0: Ethernet address: 02:06:1b:09:dc:c3 May 22 14:48:20 hairball kernel: sbp0: <SBP-2/SCSI over FireWire> on firewire0 May 22 14:48:20 hairball kernel: fwohci0: Initiate bus reset May 22 14:48:20 hairball kernel: fwohci0: node_id=0xc000ffc0, gen=1, CYCLEMASTER mode May 22 14:48:20 hairball kernel: firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me) May 22 14:48:20 hairball kernel: firewire0: bus manager 0 (me) May 22 14:48:20 hairball kernel: fxp0: <Intel 82801DB (ICH4) Pro/100 VE Ethernet> port 0x8400-0x843f mem 0xc0208000-0xc0208fff irq 11 at device 8.0 on pci2 May 22 14:48:20 hairball kernel: miibus0: <MII bus> on fxp0 May 22 14:48:20 hairball kernel: inphy0: <i82562ET 10/100 media interface> on miibus0 May 22 14:48:20 hairball kernel: inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto May 22 14:48:20 hairball kernel: fxp0: Ethernet address: 00:06:1b:d4:72:bb May 22 14:48:20 hairball kernel: fxp0: [GIANT-LOCKED] May 22 14:48:20 hairball kernel: isab0: <PCI-ISA bridge> at device 31.0 on pci0 May 22 14:48:20 hairball kernel: isa0: <ISA bus> on isab0 May 22 14:48:20 hairball kernel: atapci0: <Intel ICH4 UDMA100 controller> port 0x1860-0x186f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 31.1 on pci0 May 22 14:48:20 hairball kernel: ata0: at 0x1f0 irq 14 on atapci0 May 22 14:48:20 hairball kernel: ata1: at 0x170 irq 15 on atapci0 May 22 14:48:20 hairball kernel: pci0: <serial bus, SMBus> at device 31.3 (no driver attached) May 22 14:48:20 hairball kernel: pcm0: <Intel ICH4 (82801DB)> port 0x18c0-0x18ff,0x1c00-0x1cff mem 0xc0000800-0xc00008ff,0xc0000c00-0xc0000dff irq 10 at device 31.5 on pci0 May 22 14:48:20 hairball kernel: pcm0: [GIANT-LOCKED] May 22 14:48:20 hairball kernel: pcm0: <Analog Devices AD1981B AC97 Codec> May 22 14:48:20 hairball kernel: pci0: <simple comms> at device 31.6 (no driver attached) May 22 14:48:20 hairball kernel: atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0 May 22 14:48:20 hairball kernel: atkbd0: <AT Keyboard> irq 1 on atkbdc0 May 22 14:48:20 hairball kernel: kbd0 at atkbd0 May 22 14:48:20 hairball kernel: atkbd0: [GIANT-LOCKED] May 22 14:48:20 hairball kernel: psm0: <PS/2 Mouse> irq 12 on atkbdc0 May 22 14:48:20 hairball kernel: psm0: [GIANT-LOCKED] May 22 14:48:20 hairball kernel: psm0: model Generic PS/2 mouse, device ID 0 May 22 14:48:20 hairball kernel: fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on acpi0 May 22 14:48:20 hairball kernel: fdc0: FIFO enabled, 8 bytes threshold May 22 14:48:20 hairball kernel: fd0: <1440-KB 3.5" drive> on fdc0 drive 0 May 22 14:48:20 hairball kernel: sio0 port 0x3f8-0x3ff irq 4 on acpi0 May 22 14:48:20 hairball kernel: sio0: type 16550A May 22 14:48:20 hairball kernel: ppc0 port 0x3bc-0x3c3 irq 7 on acpi0 May 22 14:48:20 hairball kernel: ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode May 22 14:48:20 hairball kernel: ppbus0: <Parallel port bus> on ppc0 May 22 14:48:20 hairball kernel: plip0: <PLIP network interface> on ppbus0 May 22 14:48:20 hairball kernel: lpt0: <Printer> on ppbus0 May 22 14:48:20 hairball kernel: lpt0: Interrupt-driven port May 22 14:48:20 hairball kernel: ppi0: <Parallel I/O> on ppbus0 May 22 14:48:20 hairball kernel: sio1: configured irq 3 not in bitmap of probed irqs 0 May 22 14:48:20 hairball kernel: sio1: port may not be enabled May 22 14:48:20 hairball kernel: acpi_cmbat0: <Control Method Battery> on acpi0 May 22 14:48:20 hairball kernel: acpi_acad0: <AC Adapter> on acpi0 May 22 14:48:20 hairball kernel: acpi_video0: <ACPI video extension> on acpi0 May 22 14:48:20 hairball kernel: acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0 May 22 14:48:20 hairball kernel: sio1: configured irq 3 not in bitmap of probed irqs 0 May 22 14:48:20 hairball kernel: sio1: port may not be enabled May 22 14:48:20 hairball kernel: sio1: configured irq 3 not in bitmap of probed irqs 0 May 22 14:48:20 hairball kernel: sio1: port may not be enabled May 22 14:48:20 hairball kernel: orm0: <Option ROMs> at iomem 0xe0000-0xeffff,0xdc000-0xdffff,0xd1000-0xd1fff,0xd0000-0xd0fff,0xc0000-0xcffff on isa0 May 22 14:48:20 hairball kernel: pmtimer0 on isa0 May 22 14:48:20 hairball kernel: sc0: <System console> at flags 0x100 on isa0 May 22 14:48:20 hairball kernel: sc0: VGA <16 virtual consoles, flags=0x300> May 22 14:48:20 hairball kernel: sio1: configured irq 3 not in bitmap of probed irqs 0 May 22 14:48:20 hairball kernel: sio1: port may not be enabled May 22 14:48:20 hairball kernel: vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 May 22 14:48:20 hairball kernel: Timecounter "TSC" frequency 1498734261 Hz quality 800 May 22 14:48:20 hairball kernel: Timecounters tick every 10.000 msec May 22 14:48:20 hairball kernel: cpu0: set speed to 100.0% May 22 14:48:20 hairball kernel: acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently 100.0% May 22 14:48:20 hairball kernel: acpi_cmbat0: battery initialization start May 22 14:48:20 hairball kernel: acpi_cmbat0: battery initialization done, tried 1 times May 22 14:48:20 hairball kernel: acpi_acad0: acline initialization start May 22 14:48:20 hairball kernel: acpi_acad0: On Line May 22 14:48:20 hairball kernel: acpi_acad0: acline initialization done, tried 1 times May 22 14:48:20 hairball kernel: ad0: 36259MB <IC25N040ATCS04-0> [73670/16/63] at ata0-master UDMA100 May 22 14:48:20 hairball kernel: pccard0: Allocation failed for cfe 32 May 22 14:48:20 hairball kernel: sio4: <INTEL CORP V92 MODEM AT-MD56XX> at port 0x2f8-0x2ff irq 5 function 0 config 33 on pccard0 May 22 14:48:20 hairball kernel: sio4: type 16550A May 22 14:48:20 hairball kernel: sio4: unable to activate interrupt in fast mode - using normal mode May 22 14:48:20 hairball kernel: cd0 at ata1 bus 0 target 0 lun 0 May 22 14:48:20 hairball kernel: cd0: <HL-DT-ST RW/DVD GCC-4240N 0211> Removable CD-ROM SCSI-0 device May 22 14:48:20 hairball kernel: cd0: 16.000MB/s transfers May 22 14:48:20 hairball kernel: cd0: Attempt to query device size failed: NOT READY, Medium not present May 22 14:48:20 hairball kernel: Mounting root from ufs:/dev/ad0s2a May 22 14:48:30 hairball kernel: pci0: Failed to set ACPI power state D3 on (null): AE_BAD_PARAMETER May 22 14:48:30 hairball kernel: drm0: <ATI Radeon LW Mobility 7500 M7> port 0x3000-0x30ff mem 0xc0100000-0xc010ffff,0xe0000000-0xe7ffffff irq 11 at device 0.0 on pci1 May 22 14:48:30 hairball kernel: info: [drm] AGP at 0xd0000000 256MB May 22 14:48:30 hairball kernel: info: [drm] Initialized radeon 1.10.0 20020828 on minor 0 May 22 14:48:56 hairball bonobo-activation-server (dl-620): iid OAFIID:BrokenNoType:20000808 has a NULL type May 22 14:48:56 hairball bonobo-activation-server (dl-620): invalid character '#' in iid 'OAFIID:This#!!%$iid%^$%_|~!OAFIID_ContainsBadChars' May 22 14:59:10 hairball kernel: acpi_button0: sleep button pressed May 22 14:59:41 hairball kernel: sio4: detached May 22 14:59:41 hairball kernel: fwohci0: fwohci_pci_suspend May 22 14:59:41 hairball kernel: an0: unknown RID: 0 May 22 14:59:41 hairball last message repeated 3 times May 22 14:59:41 hairball kernel: fwohci0: fwohci_pci_resume: power_state = 0x00000000 May 22 14:59:41 hairball kernel: fwohci0: Phy 1394a available S400, 1 ports. May 22 14:59:41 hairball kernel: fwohci0: Link S400, max_rec 2048 bytes. May 22 14:59:41 hairball kernel: fwohci0: Initiate bus reset May 22 14:59:41 hairball kernel: wakeup from sleeping state (slept 00:00:32) May 22 14:59:41 hairball kernel: fwohci0: BUS reset May 22 14:59:41 hairball kernel: fwohci0: node_id=0xc000ffc0, gen=1, CYCLEMASTER mode May 22 14:59:42 hairball kernel: firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me) May 22 14:59:42 hairball kernel: firewire0: bus manager 0 (me) May 22 14:59:42 hairball kernel: fwohci0: unrecoverable error May 22 14:59:42 hairball kernel: uhub1: at uhub0 port 1 (addr 2) disconnected May 22 14:59:42 hairball kernel: uhub1: detached May 22 14:59:42 hairball kernel: acpi_cmbat0: battery initialization start May 22 14:59:42 hairball kernel: acpi_cmbat0: battery initialization done, tried 1 times May 22 14:59:43 hairball kernel: uhub1: IBM Corporation product 0x4482, class 9/0, rev 2.00/0.00, addr 2 May 22 14:59:43 hairball kernel: uhub1: 4 ports with 4 removable, self powered May 22 14:59:44 hairball kernel: pccard0: Allocation failed for cfe 32 May 22 14:59:44 hairball kernel: sio4: <INTEL CORP V92 MODEM AT-MD56XX> at port 0x2f8-0x2ff irq 5 function 0 config 33 on pccard0 May 22 14:59:44 hairball kernel: sio4: type 16550A May 22 14:59:44 hairball kernel: sio4: unable to activate interrupt in fast mode - using normal mode May 22 15:00:11 hairball kernel: Interrupt storm detected on "irq11: fwohci0 fxp*"; throttling interrupt source
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?200405230603.i4N62u7E035421>