Date: Thu, 18 Sep 2008 09:40:52 +0900 From: Pyun YongHyeon <pyunyh@gmail.com> To: Stanislav Sedov <stas@FreeBSD.org> Cc: hpcharles@gmail.com, current@FreeBSD.org Subject: Re: Attansic L2 driver test request Message-ID: <20080918004051.GA10518@cdnetworks.co.kr> In-Reply-To: <20080917145311.ff399006.stas@FreeBSD.org> References: <20080627163107.deccdd55.stas@FreeBSD.org> <4734a3ed0809170300y33ee44e0u684a5820a0f392ab@mail.gmail.com> <20080917145311.ff399006.stas@FreeBSD.org>
next in thread | previous in thread | raw e-mail | index | archive | help
On Wed, Sep 17, 2008 at 02:53:11PM +0400, Stanislav Sedov wrote: > On Wed, 17 Sep 2008 12:00:47 +0200 > "Henri-Pierre Charles" <hpcharles@gmail.com> mentioned: > > > Hello, I just discover your messages, I tried to use FreeBSD on my eeepc. > > > > 7.0-release has to be patched for ath0 > > 8.0-CURRENT-200809 work out of the box > > > > On Fri, Jun 27, 2008 at 2:31 PM, Stanislav Sedov <stas@freebsd.org> wrote: > > > For last weeks I was working on implementing an Attansic L2 > > > driver for FreeBSD that can be found on some of Asus motherboards > > > and Asus EeePC. I'm not sure if discrete adapters are available. > > > For the moment, I've implemented all the basic stuff, and the > > > drivers seems to perform stable enough. > > > http://www.SpringDaemons.com/stas/if_ae-1214569185.tar.bz2 > > > > I've tried your driver, but I'm not a specialist of device debug. > > So far I've tried : > > -- > > wget http://www.springdaemons.com/stas/if_ae-1214569185.tar.bz2 > > tar xvfz if_ae-1214569185.tar.bz2 > > cd if_ae > > make > > sudo kldload `pwd`/if_ae.ko > > ifconfig ae0 > > > > -- > > Just after the last command the ae0 interface show up and give > > ae0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 > > options=8<VLAN_MTU> > > ether 00:1e:8c:bc:9f:7a > > media: Ethernet autoselect (100baseTX <full-duplex>) > > status: active > > > > /var/log/message contain : > > Sep 17 09:55:55 eeebsd kernel: ae0: <Attansic Technology Corp, L2 > > FastEthernet> mem 0xfbfc0000-0xfbffffff irq 17 at device 0.0 on pci3 > > Sep 17 09:55:55 eeebsd kernel: ae0: pci device revision: 0xa0 > > Sep 17 09:55:55 eeebsd kernel: ae0: chip id: 0x3 > > Sep 17 09:55:55 eeebsd kernel: miibus0: <MII bus> on ae0 > > Sep 17 09:55:55 eeebsd kernel: ukphy0: <Generic IEEE 802.3u media > > interface> PHY 0 on miibus0 > > Sep 17 09:55:55 eeebsd kernel: ukphy0: 10baseT, 10baseT-FDX, > > 100baseTX, 100baseTX-FDX, auto > > Sep 17 09:55:55 eeebsd kernel: ae0: Ethernet address: 00:1e:8c:bc:9f:7a > > Sep 17 09:55:55 eeebsd kernel: ae0: [FILTER] > > Sep 17 09:55:56 eeebsd kernel: ae0: link state changed to DOWN > > Sep 17 09:56:37 eeebsd kernel: ae0: link state changed to UP > > > > But all test to use it freeze the system : > > ifconfig ae0 up of dhclient ae0. > > > > Tested on 8.0-CURRENT-200809 > > > > Can I test anythink else ? > > > > Thanks for your work ! > > > > Try the latest version from > http://wiki.freebsd.org/AsusEee > The information for Atheros L1 FastEthernet in the URL looks incorrect. AFAIK the second generation of L1, also known as L1E, is PCIe *Gigabit* controller. -- Regards, Pyun YongHyeon
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20080918004051.GA10518>