Date: Mon, 24 Aug 2009 05:45:11 +0200 From: Gianni <gdoe6545@yahoo.it> To: freebsd-usb@freebsd.org Subject: Re: Huawei E169 USB 3G Modem not detected as modem in 7.2 Message-ID: <24C44DD8-EA6D-448C-B610-EB4EAB561CBB@yahoo.it> In-Reply-To: <200908240044.n7O0iXAe041209@lava.sentex.ca> References: <5B4090AC-F8B3-4AAF-8501-FEAFE087EBCE@yahoo.it> <200908240044.n7O0iXAe041209@lava.sentex.ca>
next in thread | previous in thread | raw e-mail | index | archive | help
On 24/ago/09, at 02:47, Mike Tancsa wrote: > At 08:05 AM 8/23/2009, Gianni wrote: >> I've seen a few posts related to the Huawei E169 3G modem which have >> reported this device as working under 7.2. I have the u3g driver >> loaded but the modem is only recognised as umass, I tried disabling >> umass and the device came up as ugen. >> My 7.2-STABLE is newly built today, log messages below, should this >> modem work out of the box or is there some extra configuration >> needed? >> Any suggestion much appreciated. > > > Make sure umass is loaded as well as the u3g driver. Then, after > all has booted up, try > usbdevs -v > camcontrol eject pass0 > usbdevs > > Some devices need that to put them into 'modem mode'... If it works, > you should see /dev/cuaU0.0 and you should see a differences in the > output of usbdevs before and after the camcontrol eject pass0 > > ---Mike Thanks Mike, unfortunately that did not work, the /dev/cuaU0.0 device did not appear. -Gianni nicknack# usbdevs -v Controller /dev/usb0: addr 1: full speed, self powered, config 1, UHCI root hub(0x0000), Intel(0x0000), rev 1.00 port 1 powered port 2 powered Controller /dev/usb1: addr 1: full speed, self powered, config 1, UHCI root hub(0x0000), Intel(0x0000), rev 1.00 port 1 powered port 2 powered Controller /dev/usb2: addr 1: full speed, self powered, config 1, UHCI root hub(0x0000), Intel(0x0000), rev 1.00 port 1 powered port 2 powered Controller /dev/usb3: addr 1: full speed, self powered, config 1, UHCI root hub(0x0000), Intel(0x0000), rev 1.00 port 1 powered port 2 powered Controller /dev/usb4: addr 1: high speed, self powered, config 1, EHCI root hub(0x0000), Intel(0x0000), rev 1.00 port 1 powered port 2 addr 3: high speed, self powered, config 1, HUAWEI Mobile(0x1446), HUAWEI Technology(0x12d1), rev 0.00 port 3 powered port 4 powered port 5 powered port 6 addr 2: high speed, power 500 mA, config 1, USB2.0- CRW(0x0158), Generic(0x0bda), rev 58.87 port 7 powered port 8 powered nicknack# camcontrol eject pass0 Unit stopped successfully, Media ejected nicknack# usbdevs -v Controller /dev/usb0: addr 1: full speed, self powered, config 1, UHCI root hub(0x0000), Intel(0x0000), rev 1.00 port 1 powered port 2 powered Controller /dev/usb1: addr 1: full speed, self powered, config 1, UHCI root hub(0x0000), Intel(0x0000), rev 1.00 port 1 powered port 2 powered Controller /dev/usb2: addr 1: full speed, self powered, config 1, UHCI root hub(0x0000), Intel(0x0000), rev 1.00 port 1 powered port 2 powered Controller /dev/usb3: addr 1: full speed, self powered, config 1, UHCI root hub(0x0000), Intel(0x0000), rev 1.00 port 1 powered port 2 powered Controller /dev/usb4: addr 1: high speed, self powered, config 1, EHCI root hub(0x0000), Intel(0x0000), rev 1.00 port 1 powered port 2 addr 3: high speed, self powered, config 1, HUAWEI Mobile(0x1446), HUAWEI Technology(0x12d1), rev 0.00 port 3 powered port 4 powered port 5 powered port 6 addr 2: high speed, power 500 mA, config 1, USB2.0- CRW(0x0158), Generic(0x0bda), rev 58.87 port 7 powered port 8 powered
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?24C44DD8-EA6D-448C-B610-EB4EAB561CBB>