Date: Sat, 03 Oct 2009 07:33:06 -0400 From: Mike Tancsa <mike@sentex.net> To: Hans Petter Selasky <hselasky@c2i.net>, freebsd-usb@freebsd.org Subject: Re: help setting u3g speed and help with new device Message-ID: <200910031133.n93BX316020861@lava.sentex.ca> In-Reply-To: <200910030929.05747.hselasky@c2i.net> References: <200910021428.n92ES6tt031519@lava.sentex.ca> <200910030929.05747.hselasky@c2i.net>
next in thread | previous in thread | raw e-mail | index | archive | help
At 03:29 AM 10/3/2009, Hans Petter Selasky wrote: > > On an older generation 378, all I did was add the device ID and all > > works just fine > > Not sure if it makes a difference, but the connect speed on the > > "working" 378 shows > > Jan 1 08:38:33 alix ppp[1758]: tun10: Chat: Received: CONNECT 3600000 > > vs > > Oct 2 10:11:37 378n ppp[1085]: tun10: Chat: Received: CONNECT 7200000 > > > > How do I find out what the "right" speed is and set it for the device ? > > > > Despite the higher connect speed, I get a transfer rate of about > > 21Kbps. On the older gen modem, I get 1,376Kbps > > > >Have you checked the 3GPP specification for AT commands which report which >carrier you are connected at? Hi, I am not sure how to do that on this unit. I did look through http://www.shapeshifter.se/wp-content/uploads/2008/04/27007-830.pdf AT command set for User Equipment (UE) but I didnt find anything that seems to report=20 the actual connect speed. Do you know of any better documentation ? >Possibly your modem is using GPRS because it doesn't find any HSDPA or >whatsoever faster carrier. I cant seem to get anything more than Oct 3 07:28:57 dw994 ppp[3474]: tun0: Chat: Received: ATD*99#^M^M Oct 3 07:28:57 dw994 ppp[3474]: tun0: Chat: Received: CONNECT 7200000^M which seems like a reasonable speed. The signal q=20 is good and the other modems around it get their full speeds as well at+csq +CSQ: 18,99 OK at&v &C: 1; &D: 2; &F: 0; E: 1; I: 0; L: 0; M: 0; Q: 0; V: 1; X: 0; Z: 0; S0: 0; S3: 13; S4: 10; S5: 8; S6: 2; S7: 50; S8: 2; S9: 6; S10: 14; S11: 95; +FCLASS: 0; +ICF: 3,3; +IFC: 2,2; +IPR: 115200; +DR: 1; +DS: 0,0,2048,6; +WS46: 12; +CBST: 0,0,1; +CRLP: (61,61,48,6,0),(61,61,48,6,1),(240,240,52,6,2); +CV120: 1,1,1,0,0,0; +CHSN: 0,0,0,0; +CSSN: 0,0; +CREG: 1; +CGREG: 0; +CFUN:; +CSCS: "IRA"; +CSTA: 129; +CR: 1; +CRC:=20 1; +CMEE: 2; +CGDCONT: (1,"IP","internet.com","0.0.0.0",0,0) ; +CGDSCONT: ; +CGTFT: ; +CGEQREQ: ; +CGEQMIN: ; +CGQREQ: ; +CGQMIN: ; +CGEREP: 0,0; +CGDATA: "PPP"; +CGCLASS: "A"; +CGSMS: 1; +CSMS: 0; +CMGF: 0; +CSCA: "+17057969300",145; +CSMP: ,,0,0; +CSDH: 0; +CSCB: 0,"",""; +FDD: 0; +FAR: 0; +FCL: 0; +FIT: 0,0; +ES: ,,; +ESA: 0,,,,0,0,255,; +CMOD: 0; +CVHU: 1; +CPIN: =FF=FF=FF=FF=FF=FF=FF=FF,=FF= =FF=FF=FF=FF=FF=FF=FF; +CMEC: 0,0,0; +CKPD: 1,1; +CGATT: 1; +CGACT: 0; +CPBS: "SM"; +CPMS: "SM","SM","SM"; +CNMI: 0,0,0,0,0; +CMMS: 0; +FTS: 0; +FRS: 0; +FTH: 3; +FRH: 3; +FTM: 96; +FRM: 96; +CCUG: 0,0,0; +CUSD: 0; +CAOC: 1; +CCWA: 0; +CLVL: 2; +CMUT: 0; +CPOL: 0,2,"",0,0,0; +CPLS: 0; +CTZR: 0; +CLIP: 0; +COLP: 1; +CLIR: 0; +CCLK:; +COPS: 0,0,"",3; +CSIM: 14,""; +CRSM: 0,0,0,0,0,""; +CSMINS: 0; +VIP: 0; +VTS: ; +VTD: 1 ---Mike >Also check for any stall printouts (not likely) when setting u3g debugging. > >--HPS -------------------------------------------------------------------- Mike Tancsa, tel +1 519 651 3400 Sentex Communications, mike@sentex.net Providing Internet since 1994 www.sentex.net Cambridge, Ontario Canada www.sentex.net/mike
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?200910031133.n93BX316020861>