Date: Thu, 24 Jan 2013 20:48:04 -0600 From: Paul Keusemann <pkeusem@visi.com> To: Marius Strobl <marius@alchemy.franken.de> Cc: freebsd-net@freebsd.org Subject: Re: Cas driver fails to load first time after boot. Message-ID: <5101F264.7030206@visi.com> In-Reply-To: <20130124215017.GS85306@alchemy.franken.de> References: <50FEFAB8.1070006@visi.com> <20130124150904.GA27559@alchemy.franken.de> <51017FF0.5080001@visi.com> <20130124215017.GS85306@alchemy.franken.de>
next in thread | previous in thread | raw e-mail | index | archive | help
This is a multi-part message in MIME format.
--------------050702010903090304000103
Content-Type: text/plain; charset=ISO-8859-1; format=flowed
Content-Transfer-Encoding: 7bit
On 01/24/13 15:50, Marius Strobl wrote:
> On Thu, Jan 24, 2013 at 12:39:44PM -0600, Paul Keusemann wrote:
>> On 01/24/13 09:09, Marius Strobl wrote:
>>> On Tue, Jan 22, 2013 at 02:46:48PM -0600, Paul Keusemann wrote:
>>>> Hi,
>>>>
>>>> I've got a Dell R200 which I'm trying to build into a gateway with a Sun
>>>> QGE (501-6738-10). The cas driver fails to load the first time I try to
>>>> load it but succeeds the second time. Is this a problem with the card,
>>>> the driver, my karma?
>>> Wrong phase of the moon, apparently :)
>>> The MII setup of these chips is a bit tricky and I'm not sure whether
>>> I've hit all code paths during development of the driver. I certainly
>>> didn't test with a 501-6738, these have been reported as working before,
>>> though. It also doesn't make much sense that attaching the devices
>>> succeeds on the second attempt. Could you please use a if_cas.ko built
>>> with the attached patch and report the debug output for one of the
>>> interfaces in both the working and the non-working case?
>> I would love to give you output from the working and non-working case
>> but apparently the phase of the moon has changed, I can't get it to fail
>> now. The messages output from the working case is attached.
>>
> Thanks but unfortunately this doesn't make any sense either. In general,
> printf()s cause deays which can be relevant. In the locations I've put
> them they hardly can make such a difference though.
> If you haven't already done so, could you please power off the machine
> before doing the test with the patched module? Is the problem still gone
> if you revert to the original module?
OK, power-cycling makes a difference. The driver fails to attach all of
the devices after power-cycling most of the time if not all of the
time. The number of devices attached varies, the attached message file
fragment is from my last test. Three of the devices were attached on
the first load attempt and all four of them on the second attempt.
In the interest of full disclosure, I did build a new kernel but it is
just a copy of GENERIC. This is a
>
> Marius
>
>
--
Paul Keusemann pkeusem@visi.com
4266 Joppa Court (952) 894-7805
Savage, MN 55378
--------------050702010903090304000103
Content-Type: text/plain; charset=us-ascii;
name="messages"
Content-Transfer-Encoding: 7bit
Content-Disposition: attachment;
filename="messages"
Jan 24 20:32:32 lucid kernel: Copyright (c) 1992-2012 The FreeBSD Project.
Jan 24 20:32:32 lucid kernel: Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
Jan 24 20:32:32 lucid kernel: The Regents of the University of California. All rights reserved.
Jan 24 20:32:32 lucid kernel: FreeBSD is a registered trademark of The FreeBSD Foundation.
Jan 24 20:32:32 lucid kernel: FreeBSD 8.3-RELEASE #0: Thu Jan 24 11:15:13 CST 2013
Jan 24 20:32:32 lucid kernel: toor@lucid:/usr/obj/usr/src/sys/LUCID amd64
Jan 24 20:32:32 lucid kernel: Timecounter "i8254" frequency 1193182 Hz quality 0
Jan 24 20:32:32 lucid kernel: CPU: Intel(R) Xeon(R) CPU X3210 @ 2.13GHz (2133.42-MHz K8-class CPU)
Jan 24 20:32:32 lucid kernel: Origin = "GenuineIntel" Id = 0x6fb Family = 6 Model = f Stepping = 11
Jan 24 20:32:32 lucid kernel: Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Jan 24 20:32:32 lucid kernel: Features2=0xe3bd<SSE3,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM>
Jan 24 20:32:32 lucid kernel: AMD Features=0x20100800<SYSCALL,NX,LM>
Jan 24 20:32:32 lucid kernel: AMD Features2=0x1<LAHF>
Jan 24 20:32:32 lucid kernel: TSC: P-state invariant
Jan 24 20:32:32 lucid kernel: real memory = 4294967296 (4096 MB)
Jan 24 20:32:32 lucid kernel: avail memory = 4099231744 (3909 MB)
Jan 24 20:32:32 lucid kernel: ACPI APIC Table: <DELL PE_SC3 >
Jan 24 20:32:32 lucid kernel: FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
Jan 24 20:32:32 lucid kernel: FreeBSD/SMP: 1 package(s) x 4 core(s)
Jan 24 20:32:32 lucid kernel: cpu0 (BSP): APIC ID: 0
Jan 24 20:32:32 lucid kernel: cpu1 (AP): APIC ID: 1
Jan 24 20:32:32 lucid kernel: cpu2 (AP): APIC ID: 2
Jan 24 20:32:32 lucid kernel: cpu3 (AP): APIC ID: 3
Jan 24 20:32:32 lucid kernel: ioapic0: Changing APIC ID to 4
Jan 24 20:32:32 lucid kernel: ioapic1: Changing APIC ID to 5
Jan 24 20:32:32 lucid kernel: ioapic0 <Version 2.0> irqs 0-23 on motherboard
Jan 24 20:32:32 lucid kernel: ioapic1 <Version 2.0> irqs 32-55 on motherboard
Jan 24 20:32:32 lucid kernel: kbd1 at kbdmux0
Jan 24 20:32:32 lucid kernel: acpi0: <DELL PE_SC3> on motherboard
Jan 24 20:32:32 lucid kernel: acpi0: [ITHREAD]
Jan 24 20:32:32 lucid kernel: acpi0: Power Button (fixed)
Jan 24 20:32:32 lucid kernel: Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
Jan 24 20:32:32 lucid kernel: acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
Jan 24 20:32:32 lucid kernel: cpu0: <ACPI CPU> on acpi0
Jan 24 20:32:32 lucid kernel: cpu1: <ACPI CPU> on acpi0
Jan 24 20:32:32 lucid kernel: cpu2: <ACPI CPU> on acpi0
Jan 24 20:32:32 lucid kernel: cpu3: <ACPI CPU> on acpi0
Jan 24 20:32:32 lucid kernel: pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
Jan 24 20:32:32 lucid kernel: pci0: <ACPI PCI bus> on pcib0
Jan 24 20:32:32 lucid kernel: pcib1: <ACPI PCI-PCI bridge> irq 16 at device 1.0 on pci0
Jan 24 20:32:32 lucid kernel: pci1: <ACPI PCI bus> on pcib1
Jan 24 20:32:32 lucid kernel: pcib2: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0
Jan 24 20:32:32 lucid kernel: pci2: <ACPI PCI bus> on pcib2
Jan 24 20:32:32 lucid kernel: pcib3: <ACPI PCI-PCI bridge> at device 0.0 on pci2
Jan 24 20:32:32 lucid kernel: pci3: <ACPI PCI bus> on pcib3
Jan 24 20:32:32 lucid kernel: pcib4: <PCI-PCI bridge> at device 2.0 on pci3
Jan 24 20:32:32 lucid kernel: pci4: <PCI bus> on pcib4
Jan 24 20:32:32 lucid kernel: pci4: <network, ethernet> at device 0.0 (no driver attached)
Jan 24 20:32:32 lucid kernel: pci4: <network, ethernet> at device 1.0 (no driver attached)
Jan 24 20:32:32 lucid kernel: pci4: <network, ethernet> at device 2.0 (no driver attached)
Jan 24 20:32:32 lucid kernel: pci4: <network, ethernet> at device 3.0 (no driver attached)
Jan 24 20:32:32 lucid kernel: pcib5: <ACPI PCI-PCI bridge> irq 16 at device 28.4 on pci0
Jan 24 20:32:32 lucid kernel: pci5: <ACPI PCI bus> on pcib5
Jan 24 20:32:32 lucid kernel: bge0: <Broadcom NetXtreme Gigabit Ethernet Controller, ASIC rev. 0x004201> mem 0xdf3f0000-0xdf3fffff irq 16 at device 0.0 on pci5
Jan 24 20:32:32 lucid kernel: bge0: CHIP ID 0x00004201; ASIC REV 0x04; CHIP REV 0x42; PCI-E
Jan 24 20:32:32 lucid kernel: miibus0: <MII bus> on bge0
Jan 24 20:32:32 lucid kernel: brgphy0: <BCM5750 10/100/1000baseTX PHY> PHY 1 on miibus0
Jan 24 20:32:32 lucid kernel: brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
Jan 24 20:32:32 lucid kernel: bge0: Ethernet address: 00:19:b9:fa:82:51
Jan 24 20:32:32 lucid kernel: bge0: [ITHREAD]
Jan 24 20:32:32 lucid kernel: pcib6: <ACPI PCI-PCI bridge> irq 17 at device 28.5 on pci0
Jan 24 20:32:32 lucid kernel: pci6: <ACPI PCI bus> on pcib6
Jan 24 20:32:32 lucid kernel: bge1: <Broadcom NetXtreme Gigabit Ethernet Controller, ASIC rev. 0x004201> mem 0xdf4f0000-0xdf4fffff irq 17 at device 0.0 on pci6
Jan 24 20:32:32 lucid kernel: bge1: CHIP ID 0x00004201; ASIC REV 0x04; CHIP REV 0x42; PCI-E
Jan 24 20:32:32 lucid kernel: miibus1: <MII bus> on bge1
Jan 24 20:32:32 lucid kernel: brgphy1: <BCM5750 10/100/1000baseTX PHY> PHY 1 on miibus1
Jan 24 20:32:32 lucid kernel: brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
Jan 24 20:32:32 lucid kernel: bge1: Ethernet address: 00:19:b9:fa:82:52
Jan 24 20:32:32 lucid kernel: bge1: [ITHREAD]
Jan 24 20:32:32 lucid kernel: uhci0: <Intel 82801I (ICH9) USB controller> port 0xdc60-0xdc7f irq 21 at device 29.0 on pci0
Jan 24 20:32:32 lucid kernel: uhci0: [ITHREAD]
Jan 24 20:32:32 lucid kernel: usbus0: <Intel 82801I (ICH9) USB controller> on uhci0
Jan 24 20:32:32 lucid kernel: uhci1: <Intel 82801I (ICH9) USB controller> port 0xdc80-0xdc9f irq 20 at device 29.1 on pci0
Jan 24 20:32:32 lucid kernel: uhci1: [ITHREAD]
Jan 24 20:32:32 lucid kernel: usbus1: <Intel 82801I (ICH9) USB controller> on uhci1
Jan 24 20:32:32 lucid kernel: uhci2: <Intel 82801I (ICH9) USB controller> port 0xdca0-0xdcbf irq 21 at device 29.2 on pci0
Jan 24 20:32:32 lucid kernel: uhci2: [ITHREAD]
Jan 24 20:32:32 lucid kernel: usbus2: <Intel 82801I (ICH9) USB controller> on uhci2
Jan 24 20:32:32 lucid kernel: ehci0: <Intel 82801I (ICH9) USB 2.0 controller> mem 0xdf2ffc00-0xdf2fffff irq 21 at device 29.7 on pci0
Jan 24 20:32:32 lucid kernel: ehci0: [ITHREAD]
Jan 24 20:32:32 lucid kernel: usbus3: EHCI version 1.0
Jan 24 20:32:32 lucid kernel: usbus3: <Intel 82801I (ICH9) USB 2.0 controller> on ehci0
Jan 24 20:32:32 lucid kernel: pcib7: <ACPI PCI-PCI bridge> at device 30.0 on pci0
Jan 24 20:32:32 lucid kernel: pci7: <ACPI PCI bus> on pcib7
Jan 24 20:32:32 lucid kernel: vgapci0: <VGA-compatible display> port 0xec00-0xecff mem 0xd0000000-0xd7ffffff,0xdf5f0000-0xdf5fffff irq 19 at device 5.0 on pci7
Jan 24 20:32:32 lucid kernel: isab0: <PCI-ISA bridge> at device 31.0 on pci0
Jan 24 20:32:32 lucid kernel: isa0: <ISA bus> on isab0
Jan 24 20:32:32 lucid kernel: atapci0: <Intel ICH9 SATA300 controller> port 0xdc30-0xdc37,0xdc28-0xdc2b,0xdc38-0xdc3f,0xdc2c-0xdc2f,0xdc40-0xdc4f,0xdc50-0xdc5f irq 23 at device 31.2 on pci0
Jan 24 20:32:32 lucid kernel: atapci0: [ITHREAD]
Jan 24 20:32:32 lucid kernel: ata2: <ATA channel> at channel 0 on atapci0
Jan 24 20:32:32 lucid kernel: ata2: [ITHREAD]
Jan 24 20:32:32 lucid kernel: ata3: <ATA channel> at channel 1 on atapci0
Jan 24 20:32:32 lucid kernel: ata3: [ITHREAD]
Jan 24 20:32:32 lucid kernel: acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
Jan 24 20:32:32 lucid kernel: Timecounter "HPET" frequency 14318180 Hz quality 900
Jan 24 20:32:32 lucid kernel: atrtc0: <AT realtime clock> port 0x70-0x7f irq 8 on acpi0
Jan 24 20:32:32 lucid kernel: fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0
Jan 24 20:32:32 lucid kernel: fdc0: does not respond
Jan 24 20:32:32 lucid kernel: device_attach: fdc0 attach returned 6
Jan 24 20:32:32 lucid kernel: uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
Jan 24 20:32:32 lucid kernel: uart0: [FILTER]
Jan 24 20:32:32 lucid kernel: atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
Jan 24 20:32:32 lucid kernel: atkbd0: <AT Keyboard> irq 1 on atkbdc0
Jan 24 20:32:32 lucid kernel: kbd0 at atkbd0
Jan 24 20:32:32 lucid kernel: atkbd0: [GIANT-LOCKED]
Jan 24 20:32:32 lucid kernel: atkbd0: [ITHREAD]
Jan 24 20:32:32 lucid kernel: psm0: <PS/2 Mouse> irq 12 on atkbdc0
Jan 24 20:32:32 lucid kernel: psm0: [GIANT-LOCKED]
Jan 24 20:32:32 lucid kernel: psm0: [ITHREAD]
Jan 24 20:32:32 lucid kernel: psm0: model Generic PS/2 mouse, device ID 0
Jan 24 20:32:32 lucid kernel: orm0: <ISA Option ROMs> at iomem 0xc0000-0xc8fff,0xc9000-0xc9fff,0xca000-0xcb7ff,0xec000-0xeffff on isa0
Jan 24 20:32:32 lucid kernel: sc0: <System console> at flags 0x100 on isa0
Jan 24 20:32:32 lucid kernel: sc0: VGA <16 virtual consoles, flags=0x300>
Jan 24 20:32:32 lucid kernel: vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Jan 24 20:32:32 lucid kernel: ppc0: cannot reserve I/O port range
Jan 24 20:32:32 lucid kernel: est0: <Enhanced SpeedStep Frequency Control> on cpu0
Jan 24 20:32:32 lucid kernel: p4tcc0: <CPU Frequency Thermal Control> on cpu0
Jan 24 20:32:32 lucid kernel: est1: <Enhanced SpeedStep Frequency Control> on cpu1
Jan 24 20:32:32 lucid kernel: p4tcc1: <CPU Frequency Thermal Control> on cpu1
Jan 24 20:32:32 lucid kernel: est2: <Enhanced SpeedStep Frequency Control> on cpu2
Jan 24 20:32:32 lucid kernel: p4tcc2: <CPU Frequency Thermal Control> on cpu2
Jan 24 20:32:32 lucid kernel: est3: <Enhanced SpeedStep Frequency Control> on cpu3
Jan 24 20:32:32 lucid kernel: p4tcc3: <CPU Frequency Thermal Control> on cpu3
Jan 24 20:32:32 lucid kernel: Timecounters tick every 1.000 msec
Jan 24 20:32:32 lucid kernel: usbus0: 12Mbps Full Speed USB v1.0
Jan 24 20:32:32 lucid kernel: usbus1: 12Mbps Full Speed USB v1.0
Jan 24 20:32:32 lucid kernel: usbus2: 12Mbps Full Speed USB v1.0
Jan 24 20:32:32 lucid kernel: usbus3: 480Mbps High Speed USB v2.0
Jan 24 20:32:32 lucid kernel: ad4: 76293MB <WDC WD800AAJS-18TDA1 01.00A04> at ata2-master UDMA100 SATA 3Gb/s
Jan 24 20:32:32 lucid kernel: ugen0.1: <Intel> at usbus0
Jan 24 20:32:32 lucid kernel: uhub0: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
Jan 24 20:32:32 lucid kernel: ugen1.1: <Intel> at usbus1
Jan 24 20:32:32 lucid kernel: uhub1: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
Jan 24 20:32:32 lucid kernel: ugen2.1: <Intel> at usbus2
Jan 24 20:32:32 lucid kernel: uhub2: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2
Jan 24 20:32:32 lucid kernel: ugen3.1: <Intel> at usbus3
Jan 24 20:32:32 lucid kernel: uhub3: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus3
Jan 24 20:32:32 lucid kernel: acd0: DVDROM <TEAC DVD-ROM DV28EV/D.AE> at ata2-slave UDMA33 SATA 1.5Gb/s
Jan 24 20:32:32 lucid kernel: SMP: AP CPU #2 Launched!
Jan 24 20:32:32 lucid kernel: SMP: AP CPU #1 Launched!
Jan 24 20:32:32 lucid kernel: SMP: AP CPU #3 Launched!
Jan 24 20:32:32 lucid kernel: Root mount waiting for: usbus3 usbus2 usbus1 usbus0
Jan 24 20:32:32 lucid kernel: uhub0: 2 ports with 2 removable, self powered
Jan 24 20:32:32 lucid kernel: uhub1: 2 ports with 2 removable, self powered
Jan 24 20:32:32 lucid kernel: uhub2: 2 ports with 2 removable, self powered
Jan 24 20:32:32 lucid kernel: Root mount waiting for: usbus3
Jan 24 20:32:32 lucid kernel: uhub3: 6 ports with 6 removable, self powered
Jan 24 20:32:32 lucid kernel: Root mount waiting for: usbus3
Jan 24 20:32:32 lucid kernel: ugen3.2: <vendor 0x04b4> at usbus3
Jan 24 20:32:32 lucid kernel: uhub4: <vendor 0x04b4 product 0x6560, class 9/0, rev 2.00/0.0b, addr 2> on usbus3
Jan 24 20:32:32 lucid kernel: uhub4: 4 ports with 4 removable, self powered
Jan 24 20:32:32 lucid kernel: Trying to mount root from ufs:/dev/ad4s1a
Jan 24 20:32:34 lucid kernel: bge0: link state changed to UP
Jan 24 20:32:41 lucid login: ROOT LOGIN (toor) ON ttyv0
Jan 24 20:32:47 lucid login: ROOT LOGIN (toor) ON ttyv1
Jan 24 20:33:07 lucid kernel: cas0: <NS DP83065 Saturn Gigabit Ethernet> mem 0xdf800000-0xdf9fffff irq 35 at device 0.0 on pci4
Jan 24 20:33:07 lucid kernel: cas0: MIF=0x100 PCFG=0x1f
Jan 24 20:33:07 lucid kernel: miibus2: <MII bus> on cas0
Jan 24 20:33:07 lucid kernel: nsgphy0: <DP83865 10/100/1000 media interface> PHY 1 on miibus2
Jan 24 20:33:07 lucid kernel: nsgphy0: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
Jan 24 20:33:07 lucid kernel: cas0: internal PHY
Jan 24 20:33:07 lucid kernel: cas0: 16kB RX FIFO, 9kB TX FIFO
Jan 24 20:33:07 lucid kernel: cas0: Ethernet address: 00:14:4f:25:ca:10
Jan 24 20:33:07 lucid kernel: cas0: [FILTER]
Jan 24 20:33:07 lucid kernel: cas1: <NS DP83065 Saturn Gigabit Ethernet> mem 0xdfa00000-0xdfbfffff irq 34 at device 1.0 on pci4
Jan 24 20:33:07 lucid kernel: cas1: MIF=0x100 PCFG=0x1f
Jan 24 20:33:07 lucid kernel: cas1: attaching PHYs failed
Jan 24 20:33:07 lucid kernel: cas1: could not be attached
Jan 24 20:33:07 lucid kernel: device_attach: cas1 attach returned 6
Jan 24 20:33:07 lucid kernel: cas2: <NS DP83065 Saturn Gigabit Ethernet> mem 0xdfc00000-0xdfdfffff irq 33 at device 2.0 on pci4
Jan 24 20:33:07 lucid kernel: cas2: MIF=0x100 PCFG=0x1f
Jan 24 20:33:07 lucid kernel: miibus3: <MII bus> on cas2
Jan 24 20:33:07 lucid kernel: nsgphy1: <DP83865 10/100/1000 media interface> PHY 1 on miibus3
Jan 24 20:33:07 lucid kernel: nsgphy1: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
Jan 24 20:33:07 lucid kernel: cas2: internal PHY
Jan 24 20:33:07 lucid kernel: cas2: 16kB RX FIFO, 9kB TX FIFO
Jan 24 20:33:07 lucid kernel: cas2: Ethernet address: 00:14:4f:25:ca:12
Jan 24 20:33:07 lucid kernel: cas2: [FILTER]
Jan 24 20:33:07 lucid kernel: cas3: <NS DP83065 Saturn Gigabit Ethernet> mem 0xdfe00000-0xdfffffff irq 32 at device 3.0 on pci4
Jan 24 20:33:07 lucid kernel: cas3: MIF=0x100 PCFG=0x1f
Jan 24 20:33:07 lucid kernel: miibus4: <MII bus> on cas3
Jan 24 20:33:07 lucid kernel: nsgphy2: <DP83865 10/100/1000 media interface> PHY 1 on miibus4
Jan 24 20:33:07 lucid kernel: nsgphy2: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
Jan 24 20:33:07 lucid kernel: cas3: internal PHY
Jan 24 20:33:07 lucid kernel: cas3: 16kB RX FIFO, 9kB TX FIFO
Jan 24 20:33:07 lucid kernel: cas3: Ethernet address: 00:14:4f:25:ca:13
Jan 24 20:33:07 lucid kernel: cas3: [FILTER]
Jan 24 20:33:23 lucid kernel: nsgphy0: detached
Jan 24 20:33:23 lucid kernel: miibus2: detached
Jan 24 20:33:23 lucid kernel: cas0: detached
Jan 24 20:33:23 lucid kernel: pci4: <network, ethernet> at device 0.0 (no driver attached)
Jan 24 20:33:23 lucid kernel: nsgphy1: detached
Jan 24 20:33:23 lucid kernel: miibus3: detached
Jan 24 20:33:23 lucid kernel: cas2: detached
Jan 24 20:33:23 lucid kernel: pci4: <network, ethernet> at device 2.0 (no driver attached)
Jan 24 20:33:23 lucid kernel: nsgphy2: detached
Jan 24 20:33:23 lucid kernel: miibus4: detached
Jan 24 20:33:23 lucid kernel: cas3: detached
Jan 24 20:33:23 lucid kernel: pci4: <network, ethernet> at device 3.0 (no driver attached)
Jan 24 20:33:38 lucid kernel: cas0: <NS DP83065 Saturn Gigabit Ethernet> mem 0xdf800000-0xdf9fffff irq 35 at device 0.0 on pci4
Jan 24 20:33:38 lucid kernel: cas0: MIF=0x100 PCFG=0x1f
Jan 24 20:33:38 lucid kernel: miibus2: <MII bus> on cas0
Jan 24 20:33:38 lucid kernel: nsgphy0: <DP83865 10/100/1000 media interface> PHY 1 on miibus2
Jan 24 20:33:38 lucid kernel: nsgphy0: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
Jan 24 20:33:38 lucid kernel: cas0: internal PHY
Jan 24 20:33:38 lucid kernel: cas0: 16kB RX FIFO, 9kB TX FIFO
Jan 24 20:33:38 lucid kernel: cas0: Ethernet address: 00:14:4f:25:ca:10
Jan 24 20:33:38 lucid kernel: cas0: [FILTER]
Jan 24 20:33:38 lucid kernel: cas1: <NS DP83065 Saturn Gigabit Ethernet> mem 0xdfa00000-0xdfbfffff irq 34 at device 1.0 on pci4
Jan 24 20:33:38 lucid kernel: cas1: MIF=0x100 PCFG=0x1f
Jan 24 20:33:38 lucid kernel: miibus3: <MII bus> on cas1
Jan 24 20:33:38 lucid kernel: nsgphy1: <DP83865 10/100/1000 media interface> PHY 1 on miibus3
Jan 24 20:33:38 lucid kernel: nsgphy1: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
Jan 24 20:33:38 lucid kernel: cas1: internal PHY
Jan 24 20:33:38 lucid kernel: cas1: 16kB RX FIFO, 9kB TX FIFO
Jan 24 20:33:38 lucid kernel: cas1: Ethernet address: 00:14:4f:25:ca:11
Jan 24 20:33:38 lucid kernel: cas1: [FILTER]
Jan 24 20:33:38 lucid kernel: cas2: <NS DP83065 Saturn Gigabit Ethernet> mem 0xdfc00000-0xdfdfffff irq 33 at device 2.0 on pci4
Jan 24 20:33:38 lucid kernel: cas2: MIF=0x100 PCFG=0x1f
Jan 24 20:33:38 lucid kernel: miibus4: <MII bus> on cas2
Jan 24 20:33:38 lucid kernel: nsgphy2: <DP83865 10/100/1000 media interface> PHY 1 on miibus4
Jan 24 20:33:38 lucid kernel: nsgphy2: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
Jan 24 20:33:38 lucid kernel: cas2: internal PHY
Jan 24 20:33:38 lucid kernel: cas2: 16kB RX FIFO, 9kB TX FIFO
Jan 24 20:33:38 lucid kernel: cas2: Ethernet address: 00:14:4f:25:ca:12
Jan 24 20:33:38 lucid kernel: cas2: [FILTER]
Jan 24 20:33:38 lucid kernel: cas3: <NS DP83065 Saturn Gigabit Ethernet> mem 0xdfe00000-0xdfffffff irq 32 at device 3.0 on pci4
Jan 24 20:33:38 lucid kernel: cas3: MIF=0x100 PCFG=0x1f
Jan 24 20:33:38 lucid kernel: miibus5: <MII bus> on cas3
Jan 24 20:33:38 lucid kernel: nsgphy3: <DP83865 10/100/1000 media interface> PHY 1 on miibus5
Jan 24 20:33:38 lucid kernel: nsgphy3: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
Jan 24 20:33:38 lucid kernel: cas3: internal PHY
Jan 24 20:33:38 lucid kernel: cas3: 16kB RX FIFO, 9kB TX FIFO
Jan 24 20:33:38 lucid kernel: cas3: Ethernet address: 00:14:4f:25:ca:13
Jan 24 20:33:38 lucid kernel: cas3: [FILTER]
--------------050702010903090304000103
Content-Type: text/plain; charset=us-ascii;
name="dmesg.out"
Content-Transfer-Encoding: 7bit
Content-Disposition: attachment;
filename="dmesg.out"
Copyright (c) 1992-2012 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.3-RELEASE #0: Thu Jan 24 11:15:13 CST 2013
toor@lucid:/usr/obj/usr/src/sys/LUCID amd64
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Xeon(R) CPU X3210 @ 2.13GHz (2133.42-MHz K8-class CPU)
Origin = "GenuineIntel" Id = 0x6fb Family = 6 Model = f Stepping = 11
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Features2=0xe3bd<SSE3,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM>
AMD Features=0x20100800<SYSCALL,NX,LM>
AMD Features2=0x1<LAHF>
TSC: P-state invariant
real memory = 4294967296 (4096 MB)
avail memory = 4099231744 (3909 MB)
ACPI APIC Table: <DELL PE_SC3 >
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
FreeBSD/SMP: 1 package(s) x 4 core(s)
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 1
cpu2 (AP): APIC ID: 2
cpu3 (AP): APIC ID: 3
ioapic0: Changing APIC ID to 4
ioapic1: Changing APIC ID to 5
ioapic0 <Version 2.0> irqs 0-23 on motherboard
ioapic1 <Version 2.0> irqs 32-55 on motherboard
kbd1 at kbdmux0
acpi0: <DELL PE_SC3> on motherboard
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
cpu0: <ACPI CPU> on acpi0
cpu1: <ACPI CPU> on acpi0
cpu2: <ACPI CPU> on acpi0
cpu3: <ACPI CPU> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> irq 16 at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pcib2: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0
pci2: <ACPI PCI bus> on pcib2
pcib3: <ACPI PCI-PCI bridge> at device 0.0 on pci2
pci3: <ACPI PCI bus> on pcib3
pcib4: <PCI-PCI bridge> at device 2.0 on pci3
pci4: <PCI bus> on pcib4
pci4: <network, ethernet> at device 0.0 (no driver attached)
pci4: <network, ethernet> at device 1.0 (no driver attached)
pci4: <network, ethernet> at device 2.0 (no driver attached)
pci4: <network, ethernet> at device 3.0 (no driver attached)
pcib5: <ACPI PCI-PCI bridge> irq 16 at device 28.4 on pci0
pci5: <ACPI PCI bus> on pcib5
bge0: <Broadcom NetXtreme Gigabit Ethernet Controller, ASIC rev. 0x004201> mem 0xdf3f0000-0xdf3fffff irq 16 at device 0.0 on pci5
bge0: CHIP ID 0x00004201; ASIC REV 0x04; CHIP REV 0x42; PCI-E
miibus0: <MII bus> on bge0
brgphy0: <BCM5750 10/100/1000baseTX PHY> PHY 1 on miibus0
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
bge0: Ethernet address: 00:19:b9:fa:82:51
bge0: [ITHREAD]
pcib6: <ACPI PCI-PCI bridge> irq 17 at device 28.5 on pci0
pci6: <ACPI PCI bus> on pcib6
bge1: <Broadcom NetXtreme Gigabit Ethernet Controller, ASIC rev. 0x004201> mem 0xdf4f0000-0xdf4fffff irq 17 at device 0.0 on pci6
bge1: CHIP ID 0x00004201; ASIC REV 0x04; CHIP REV 0x42; PCI-E
miibus1: <MII bus> on bge1
brgphy1: <BCM5750 10/100/1000baseTX PHY> PHY 1 on miibus1
brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
bge1: Ethernet address: 00:19:b9:fa:82:52
bge1: [ITHREAD]
uhci0: <Intel 82801I (ICH9) USB controller> port 0xdc60-0xdc7f irq 21 at device 29.0 on pci0
uhci0: [ITHREAD]
usbus0: <Intel 82801I (ICH9) USB controller> on uhci0
uhci1: <Intel 82801I (ICH9) USB controller> port 0xdc80-0xdc9f irq 20 at device 29.1 on pci0
uhci1: [ITHREAD]
usbus1: <Intel 82801I (ICH9) USB controller> on uhci1
uhci2: <Intel 82801I (ICH9) USB controller> port 0xdca0-0xdcbf irq 21 at device 29.2 on pci0
uhci2: [ITHREAD]
usbus2: <Intel 82801I (ICH9) USB controller> on uhci2
ehci0: <Intel 82801I (ICH9) USB 2.0 controller> mem 0xdf2ffc00-0xdf2fffff irq 21 at device 29.7 on pci0
ehci0: [ITHREAD]
usbus3: EHCI version 1.0
usbus3: <Intel 82801I (ICH9) USB 2.0 controller> on ehci0
pcib7: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci7: <ACPI PCI bus> on pcib7
vgapci0: <VGA-compatible display> port 0xec00-0xecff mem 0xd0000000-0xd7ffffff,0xdf5f0000-0xdf5fffff irq 19 at device 5.0 on pci7
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH9 SATA300 controller> port 0xdc30-0xdc37,0xdc28-0xdc2b,0xdc38-0xdc3f,0xdc2c-0xdc2f,0xdc40-0xdc4f,0xdc50-0xdc5f irq 23 at device 31.2 on pci0
atapci0: [ITHREAD]
ata2: <ATA channel> at channel 0 on atapci0
ata2: [ITHREAD]
ata3: <ATA channel> at channel 1 on atapci0
ata3: [ITHREAD]
acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
Timecounter "HPET" frequency 14318180 Hz quality 900
atrtc0: <AT realtime clock> port 0x70-0x7f irq 8 on acpi0
fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0
fdc0: does not respond
device_attach: fdc0 attach returned 6
uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
uart0: [FILTER]
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: [ITHREAD]
psm0: model Generic PS/2 mouse, device ID 0
orm0: <ISA Option ROMs> at iomem 0xc0000-0xc8fff,0xc9000-0xc9fff,0xca000-0xcb7ff,0xec000-0xeffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
ppc0: cannot reserve I/O port range
est0: <Enhanced SpeedStep Frequency Control> on cpu0
p4tcc0: <CPU Frequency Thermal Control> on cpu0
est1: <Enhanced SpeedStep Frequency Control> on cpu1
p4tcc1: <CPU Frequency Thermal Control> on cpu1
est2: <Enhanced SpeedStep Frequency Control> on cpu2
p4tcc2: <CPU Frequency Thermal Control> on cpu2
est3: <Enhanced SpeedStep Frequency Control> on cpu3
p4tcc3: <CPU Frequency Thermal Control> on cpu3
Timecounters tick every 1.000 msec
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 12Mbps Full Speed USB v1.0
usbus3: 480Mbps High Speed USB v2.0
ad4: 76293MB <WDC WD800AAJS-18TDA1 01.00A04> at ata2-master UDMA100 SATA 3Gb/s
ugen0.1: <Intel> at usbus0
uhub0: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
ugen1.1: <Intel> at usbus1
uhub1: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
ugen2.1: <Intel> at usbus2
uhub2: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2
ugen3.1: <Intel> at usbus3
uhub3: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus3
acd0: DVDROM <TEAC DVD-ROM DV28EV/D.AE> at ata2-slave UDMA33 SATA 1.5Gb/s
SMP: AP CPU #2 Launched!
SMP: AP CPU #1 Launched!
SMP: AP CPU #3 Launched!
Root mount waiting for: usbus3 usbus2 usbus1 usbus0
uhub0: 2 ports with 2 removable, self powered
uhub1: 2 ports with 2 removable, self powered
uhub2: 2 ports with 2 removable, self powered
Root mount waiting for: usbus3
uhub3: 6 ports with 6 removable, self powered
Root mount waiting for: usbus3
ugen3.2: <vendor 0x04b4> at usbus3
uhub4: <vendor 0x04b4 product 0x6560, class 9/0, rev 2.00/0.0b, addr 2> on usbus3
uhub4: 4 ports with 4 removable, self powered
Trying to mount root from ufs:/dev/ad4s1a
bge0: link state changed to UP
cas0: <NS DP83065 Saturn Gigabit Ethernet> mem 0xdf800000-0xdf9fffff irq 35 at device 0.0 on pci4
cas0: MIF=0x100 PCFG=0x1f
miibus2: <MII bus> on cas0
nsgphy0: <DP83865 10/100/1000 media interface> PHY 1 on miibus2
nsgphy0: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
cas0: internal PHY
cas0: 16kB RX FIFO, 9kB TX FIFO
cas0: Ethernet address: 00:14:4f:25:ca:10
cas0: [FILTER]
cas1: <NS DP83065 Saturn Gigabit Ethernet> mem 0xdfa00000-0xdfbfffff irq 34 at device 1.0 on pci4
cas1: MIF=0x100 PCFG=0x1f
cas1: attaching PHYs failed
cas1: could not be attached
device_attach: cas1 attach returned 6
cas2: <NS DP83065 Saturn Gigabit Ethernet> mem 0xdfc00000-0xdfdfffff irq 33 at device 2.0 on pci4
cas2: MIF=0x100 PCFG=0x1f
miibus3: <MII bus> on cas2
nsgphy1: <DP83865 10/100/1000 media interface> PHY 1 on miibus3
nsgphy1: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
cas2: internal PHY
cas2: 16kB RX FIFO, 9kB TX FIFO
cas2: Ethernet address: 00:14:4f:25:ca:12
cas2: [FILTER]
cas3: <NS DP83065 Saturn Gigabit Ethernet> mem 0xdfe00000-0xdfffffff irq 32 at device 3.0 on pci4
cas3: MIF=0x100 PCFG=0x1f
miibus4: <MII bus> on cas3
nsgphy2: <DP83865 10/100/1000 media interface> PHY 1 on miibus4
nsgphy2: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
cas3: internal PHY
cas3: 16kB RX FIFO, 9kB TX FIFO
cas3: Ethernet address: 00:14:4f:25:ca:13
cas3: [FILTER]
nsgphy0: detached
miibus2: detached
cas0: detached
pci4: <network, ethernet> at device 0.0 (no driver attached)
nsgphy1: detached
miibus3: detached
cas2: detached
pci4: <network, ethernet> at device 2.0 (no driver attached)
nsgphy2: detached
miibus4: detached
cas3: detached
pci4: <network, ethernet> at device 3.0 (no driver attached)
cas0: <NS DP83065 Saturn Gigabit Ethernet> mem 0xdf800000-0xdf9fffff irq 35 at device 0.0 on pci4
cas0: MIF=0x100 PCFG=0x1f
miibus2: <MII bus> on cas0
nsgphy0: <DP83865 10/100/1000 media interface> PHY 1 on miibus2
nsgphy0: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
cas0: internal PHY
cas0: 16kB RX FIFO, 9kB TX FIFO
cas0: Ethernet address: 00:14:4f:25:ca:10
cas0: [FILTER]
cas1: <NS DP83065 Saturn Gigabit Ethernet> mem 0xdfa00000-0xdfbfffff irq 34 at device 1.0 on pci4
cas1: MIF=0x100 PCFG=0x1f
miibus3: <MII bus> on cas1
nsgphy1: <DP83865 10/100/1000 media interface> PHY 1 on miibus3
nsgphy1: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
cas1: internal PHY
cas1: 16kB RX FIFO, 9kB TX FIFO
cas1: Ethernet address: 00:14:4f:25:ca:11
cas1: [FILTER]
cas2: <NS DP83065 Saturn Gigabit Ethernet> mem 0xdfc00000-0xdfdfffff irq 33 at device 2.0 on pci4
cas2: MIF=0x100 PCFG=0x1f
miibus4: <MII bus> on cas2
nsgphy2: <DP83865 10/100/1000 media interface> PHY 1 on miibus4
nsgphy2: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
cas2: internal PHY
cas2: 16kB RX FIFO, 9kB TX FIFO
cas2: Ethernet address: 00:14:4f:25:ca:12
cas2: [FILTER]
cas3: <NS DP83065 Saturn Gigabit Ethernet> mem 0xdfe00000-0xdfffffff irq 32 at device 3.0 on pci4
cas3: MIF=0x100 PCFG=0x1f
miibus5: <MII bus> on cas3
nsgphy3: <DP83865 10/100/1000 media interface> PHY 1 on miibus5
nsgphy3: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
cas3: internal PHY
cas3: 16kB RX FIFO, 9kB TX FIFO
cas3: Ethernet address: 00:14:4f:25:ca:13
cas3: [FILTER]
--------------050702010903090304000103--
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?5101F264.7030206>