Date: Mon, 28 Mar 2005 16:47:55 -0800 From: Julian Elischer <julian@elischer.org> To: John Mok <jmok@attglobal.net> Cc: freebsd-net@freebsd.org Subject: Re: HOWTO connect MCI using Netgraph + Frame Relay with Digi SYNC/570i Message-ID: <4248A5BB.3040508@elischer.org> In-Reply-To: <424898E3.8080007@attglobal.net> References: <42344AF7.6070701@attglobal.net> <423C72A1.7060000@cronyx.ru> <4240497D.5030304@attglobal.net> <42404B15.5040605@elischer.org> <424835C0.9070603@attglobal.net> <42485836.6030203@elischer.org> <424898E3.8080007@attglobal.net>
next in thread | previous in thread | raw e-mail | index | archive | help
John Mok wrote: > > The command "ngctl types" shows :- > > There are 5 total types: > Type name Number of living nodes > --------- ---------------------- > socket 1 > rfc1490 0 > lmi 0 > frame_relay 0 > sync_ar 2 > > What other modules are needed? How to add them, whether load them > dynamically or compiled into kernel? > > Thanks a lot. kldload ng_iface at least it should be loaded automatically if you add the line shown below.. > > John Mok > > > Julian Elischer wrote: > >> what does >> "ngctl types" >> say? >> >> looks like you don't have all the right modules loaded.. >> >> >> John Mok wrote: >> >>> >>> After issuing the following commands :- >>> >>> #ngctl mkpeer sync_ar0: frame_relay rawdata downstream >> ngctl name sync_ar0:rawdata fr-mux replace the next line with.. #ngctl mkpeer fr-mux: lmi dlci0 ansi and add: ngctl name fr-mux:dlci0 lmi >>> #ngctl mkpeer sync_ar0:rawdata rfc1490 dlci16 rfc1490 >> this could be replaved by: ngctl mkpeer fr-mux: rfc1490 dlci16 downstream >>> #ngctl mkpeer sync_ar0:rawdata dlci16 rl0 inet inet >> this line is totally confused.. should be: ngctl name fr-mux:dlci16 protomux ngctl mkpeer protomux: iface inet inet now you can add the ip addresses.. sorry I didn't read it better several days ago.. >>> >>> #ifconfig ng0 1.2.3.4 5.6.7.8 >>> ifconfig: interface ng0 does not exist >> >> >> >> >> >> are you SURE none of these returned an error? >> >>> >>> The command ifconfig shows :- >>> >>> rl0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 >>> options=8<VLAN_MTU> >>> inet6 fe80::207:40ff:fe09:f09%rl0 prefixlen 64 scopeid 0x1 >>> inet 192.168.255.254 netmask 0xffffff00 broadcast 192.168.255.255 >>> ether 00:07:40:09:0f:09 >>> media: Ethernet autoselect (none) >>> status: no carrier >>> xl0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 >>> options=9<RXCSUM,VLAN_MTU> >>> inet6 fe80::201:3ff:fec1:9c58%xl0 prefixlen 64 scopeid 0x2 >>> ether 00:01:03:c1:9c:58 >>> media: Ethernet autoselect (100baseTX <full-duplex>) >>> status: active >>> xl1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 >>> options=9<RXCSUM,VLAN_MTU> >>> inet6 fe80::201:3ff:fe34:61af%xl1 prefixlen 64 scopeid 0x3 >>> inet 192.168.16.254 netmask 0xffffff00 broadcast 192.168.16.255 >>> ether 00:01:03:34:61:af >>> media: Ethernet autoselect (100baseTX <full-duplex>) >>> status: active >>> plip0: flags=108810<POINTOPOINT,SIMPLEX,MULTICAST> mtu 1500 >>> lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384 >>> inet6 ::1 prefixlen 128 >>> inet6 fe80::1%lo0 prefixlen 64 scopeid 0x5 >>> inet 127.0.0.1 netmask 0xff000000 >>> >>> and the command "ngctl list" shows :- >>> >>> There are 4 total nodes: >>> Name: ngctl811 Type: socket ID: 00000011 Num >>> hooks: 0 >>> Name: <unnamed> Type: frame_relay ID: 00000004 Num >>> hooks: 1 >>> Name: sync_ar1 Type: sync_ar ID: 00000002 Num >>> hooks: 0 >>> Name: sync_ar0 Type: sync_ar ID: 00000001 Num >>> hooks: 1 >>> >>> Would it be the problem that I test it with cable disconnected from >>> the modem (i.e.CSU/DSU)? >>> >>> Thanks a lot. >>> >>> John Mok >>> >>> >>> Julian Elischer wrote: >>> >>>> did the last command do anything? >>>> >>>> please show the output of: >>>> ifconfig >>>> ngctl list >>>> >>>> >>
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?4248A5BB.3040508>