Date: Wed, 11 Jun 2008 01:07:08 +0800 From: Razor <bg1tpt@gmail.com> To: "Sam Leffler" <sam@freebsd.org> Cc: freebsd-hardware@freebsd.org Subject: Re: The wireless card can not use after I upgrade to 8-CURRENT. IBM THINKPAD T23 Message-ID: <5e81405d0806101007t1f86a481vee58b95c3c882a03@mail.gmail.com> In-Reply-To: <484EA968.60303@freebsd.org> References: <5e81405d0806090649y7e615b93i3d97be08e29c42cf@mail.gmail.com> <484EA968.60303@freebsd.org>
next in thread | previous in thread | raw e-mail | index | archive | help
OK, Thanks. And here is my boot messages of wi0:
wi0: <Intersil Prism2.5> mem 0xec000000-0xec000fff irq 11 at device 2.0 on pci2
wi0: [ITHREAD]
wi0: using RF:PRISM2.5 MAC:ISL3874A(Mini-PCI)
wi0: Intersil Firmware: Primary (1.1.0), Station (1.4.2)
On Wed, Jun 11, 2008 at 12:18 AM, Sam Leffler <sam@freebsd.org> wrote:
> Razor wrote:
>>
>> The card works well in FreeBSD 7.0-RELEASE. After I upgrade to
>> 8-CURRENT. The wlan0 can not associate with my AP. Here is my rc.conf
>> and wpa_supplicant.conf
>>
>> rc.conf:
>>
>> wlans_wi0=wlan0
>> ifconfig_wlan0="WPA DHCP"
>>
>> /etc/wpa_supplicant.conf:
>> ctrl_interface=/var/run/wpa_supplicant
>> network={
>> ssid="FreeBSD"
>> scan_ssid=1
>> key_mgmt=NONE
>> wep_tx_keyidx=0
>> wep_key0=ABCDEF01234567890ABCDEF012
>> }
>>
>> ifconfig wi0:
>> wi0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 2290
>> ether 00:20:e0:8a:2d:88
>> media: IEEE 802.11 Wireless Ethernet autoselect mode 11b
>> status: associated
>>
>> ifconfig wlan0:
>> wlan0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu
>> 1500
>> ether 00:20:e0:8a:2d:88
>> media: IEEE 802.11 Wireless Ethernet autoselect (autoselect)
>> status: no carrier
>> ssid "" channel 10 (2457 Mhz 11b)
>> country US authmode WPA1+WPA2/802.11i privacy ON deftxkey UNDEF
>> txpower 0 bmiss 7 scanvalid 60 roaming MANUAL bintval 0
>>
>
> Intersil prism cards should work fine though they may require a firmware
> upgrade to ~rev 1.7. Unfortunately you've not shown the boot messages for
> the wi device so there's no way to tell what card you have.
>
> Other devices that used to be supported by wi were broken in the vap
> conversion. Someone else will need to step up and fix the driver to support
> them; I have no time right now.
>
> Sam
>
>
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?5e81405d0806101007t1f86a481vee58b95c3c882a03>