Date: Mon, 8 Dec 2014 12:11:34 +0100 (CET) From: elof2@sentor.se To: "Alexey V. Panfilov" <lehis@starnet.ru> Cc: freebsd-net <freebsd-net@freebsd.org> Subject: Re: IPMI stops respond if boot in single user mode Message-ID: <alpine.BSF.2.00.1412081207290.89836@farmermaggot.shire.sentor.se> In-Reply-To: <5473582D.9060100@starnet.ru> References: <546F1A96.1060309@mail.ru> <5473582D.9060100@starnet.ru>
next in thread | previous in thread | raw e-mail | index | archive | help
(Late response) I don't have an IBM-server, but isn't it equipped with a dedicated ILO/IPMI NIC? If so, the solution is rather to use that dedicated NIC instead of letting ILO/IPMI reuse the NIC for the OS. /Elof On Mon, 24 Nov 2014, Alexey V. Panfilov wrote: > 21.11.2014 13:57, Alexey V. Panfilov wrote: >> Hi, >> >> My IBM System x3250 M5 has IPMI. It shares onboard NIC Broadcom BCM5719. >> I'm setup it and IPMI works perfectly. >> But when server boots in single user mode IPMI's IP becomes unreachable. >> It occures when bge0 init. >> >> Any hints? >> >> Thanks. >> >> >> Details are: >> >> FreeBSD 10.1-STABLE (r274690) amd64 >> >> /boot/loader.conf >> hw.bge.allow_asf=1 >> >> >> bge0: <Broadcom NetXtreme Gigabit Ethernet Controller, ASIC rev. >> 0x5719001> mem >> 0x82a50000-0x82a5ffff,0x82a40000-0x82a4ffff,0x82a30000-0x82a3ffff irq 16 >> at device 0.0 on pci6 >> bge0: APE FW version: NCSI v1.2.33.0 >> bge0: CHIP ID 0x05719001; ASIC REV 0x5719; CHIP REV 0x57190; PCI-E >> miibus0: <MII bus> on bge0 >> brgphy0: <BCM5719C 1000BASE-T media interface> PHY 1 on miibus0 >> brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, >> 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow >> bge0: Using defaults for TSO: 65518/35/2048 >> bge0: Ethernet address: 6c:ae:8b:5b:74:98 >> >> >> bge0@pci0:6:0:0: class=0x020000 card=0x04911014 chip=0x165714e4 >> rev=0x01 hdr=0x00 >> vendor = 'Broadcom Corporation' >> device = 'NetXtreme BCM5719 Gigabit Ethernet PCIe' >> class = network >> subclass = ethernet >> bar [10] = type Prefetchable Memory, range 64, base 0x82a50000, >> size 65536, enabled >> bar [18] = type Prefetchable Memory, range 64, base 0x82a40000, >> size 65536, enabled >> bar [20] = type Prefetchable Memory, range 64, base 0x82a30000, >> size 65536, enabled >> cap 01[48] = powerspec 3 supports D0 D3 current D0 >> cap 03[50] = VPD >> cap 05[58] = MSI supports 8 messages, 64 bit enabled with 1 message >> cap 11[a0] = MSI-X supports 17 messages >> Table in map 0x20[0x0], PBA in map 0x20[0x1000] >> cap 10[ac] = PCI-Express 2 endpoint max data 128(256) FLR link x2(x4) >> speed 5.0(5.0) ASPM disabled(L0s/L1) >> ecap 0001[100] = AER 1 0 fatal 0 non-fatal 1 corrected >> ecap 0003[13c] = Serial 1 00006cae8b5b7498 >> ecap 0004[150] = Power Budgeting 1 >> ecap 0002[160] = VC 1 max VC0 >> >> > > When it boots in single-user mode and manually run: > > #ifconfig bge0 up > > then ipmi become accessable. > > How it can be fixed automatically after system is boot in single-user mode? > > > -- > With best regards, > Alexey V. Panfilov > > phone: (495)678-8007 ext 6000 > mail: lehis@starnet.ru > _______________________________________________ > freebsd-net@freebsd.org mailing list > http://lists.freebsd.org/mailman/listinfo/freebsd-net > To unsubscribe, send any mail to "freebsd-net-unsubscribe@freebsd.org" >
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?alpine.BSF.2.00.1412081207290.89836>