Date: Sat, 21 Apr 2012 16:31:56 +0200 From: Juergen Lock <nox@jelal.kn-bremen.de> To: Christian Kniep <kniep@videobeatz.de> Cc: freebsd-multimedia@FreeBSD.org, hselasky@FreeBSD.org Subject: Re: DVB-C (CT-3650) with german KabelBW provider under freebsd Message-ID: <20120421143156.GA36513@triton8.kn-bremen.de> In-Reply-To: <67DF20CF-A121-4361-A6A3-99C43B255FD7@videobeatz.de> References: <6A785F59-A051-4F8B-8DA1-D81D7E92D03B@videobeatz.de> <20120415144949.GA75278@triton8.kn-bremen.de> <67DF20CF-A121-4361-A6A3-99C43B255FD7@videobeatz.de>
next in thread | previous in thread | raw e-mail | index | archive | help
On Sat, Apr 21, 2012 at 12:08:31PM +0200, Christian Kniep wrote: > Hi Jürgen, Hi! > > thx for the tipps you provided. I was busy last week so I just started looking into it again. > > Am 15.04.2012 um 16:49 schrieb Juergen Lock: > > > On Sat, Apr 14, 2012 at 03:41:46PM +0200, Christian Kniep wrote: > >> Hey fellows, > > Hi! > >> > >> I am a fresh starter with freebsd but I am pretty exited about it the last couple of days. > >> I bought a N36L from HP and it fits my needs perfectly. > >> 4x2TB as raidz1 (previously on debian with zfs-fuse) and a couple of services I am playing around with. > >> > >> My current problem is that I can't bring the CT-3650 I bought to work with vdr-1.7. > >> webcamd finds them and the device is created, but I could not get any DVB-C bouqet. > >> I try to debug this by adding some parameters, but besides the "Creating*"-output I failed. > >> > >> # webcamd -m dvb-ttusb-budget.debug=1 dvb_frontend.frontend_debug=1 dvb-pll.debug=1 ttusb_dec.debug=1 dvb-usb-init.debug=31 > >> Attached ugen1.4[0] to cuse unit 0 > >> Creating /dev/dvb/adapter0/demux0 > >> Creating /dev/dvb/adapter0/dvr0 > >> Creating /dev/dvb/adapter0/frontend0 > >> Creating /dev/input/event0 > >> > > To see driver messages here you need to build the webcamd port with the > > DEBUG knob enabled. > With the new webcamd-version build (without vTuner) I got > paso# pwd > /root/ports/multimedia/webcamd > paso# cat distinfo > SHA256 (webcamd-3.4.0.1.tar.bz2) = b069d99e521392d5afc771229efa779a5050a7dbfd3f86f24ff05e3f4154e6c2 > SIZE (webcamd-3.4.0.1.tar.bz2) = 9128935 > paso# webcamd > lirc_dev: IR Remote Control driver registered, major 14 > IR NEC protocol handler initialized > IR RC5(x) protocol handler initialized > IR RC6 protocol handler initialized > IR JVC protocol handler initialized > IR Sony protocol handler initialized > IR RC5 (streamzap) protocol handler initialized > IR SANYO protocol handler initialized > IR LIRC bridge handler initialized > Linux video capture interface: v2.00 > Em28xx: Initialized (Em28xx dvb Extension) extension > USBVision USB Video Device Driver for Linux : 0.9.11 > pvrusb2: V4L in-tree version:Hauppauge WinTV-PVR-USB2 MPEG2 Encoder/Tuner > pvrusb2: Debug mask is 31 (0x1f) > cpia2: V4L-Driver for Vision CPiA2 based cameras v3.0.1 > au0828 driver loaded > uvcvideo: Unable to create debugfs directory > USB Video Class driver (1.1.1) > b2c2-flexcop: B2C2 FlexcopII/II(b)/III digital TV receiver chip loaded successfully > Attached ugen1.4[0] to cuse unit 0 > dvb-usb: found a 'Technotrend TT-connect CT-3650' in warm state. > dvb-usb: bulk message failed: -32 (4/0) > ttusb2: there might have been an error during control message transfer. (rlen = 0, was 0) > dvb-usb: bulk message failed: -32 (5/0) > ttusb2: there might have been an error during control message transfer. (rlen = 0, was 0) > dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer. > dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer. > DVB: registering new adapter (Technotrend TT-connect CT-3650) > dvb-usb: bulk message failed: -32 (9/0) > ttusb2: there might have been an error during control message transfer. (rlen = 3, was 0) > ttusb2: i2c transfer failed. > DVB: TDA10023(-1): tda10023_writereg, writereg error (reg == 0x00, val == 0x33, ret == 0) > dvb-usb: bulk message failed: -32 (8/0) > ttusb2: there might have been an error during control message transfer. (rlen = 4, was 0) > ttusb2: i2c transfer failed. > DVB: TDA10023(-1): tda10023_readreg: readreg error (reg == 0x1a, ret == 0) > dvb-usb: no frontend was attached by 'Technotrend TT-connect CT-3650' > Registered IR keymap rc-tt-1500 > rc0: IR-receiver inside an USB DVB receiver as webcamd > dvb-usb: schedule remote query interval to 150 msecs. > dvb-usb: bulk message failed: -32 (4/0) > ttusb2: there might have been an error during control message transfer. (rlen = 0, was 0) > dvb-usb: bulk message failed: -32 (4/0) > ttusb2: there might have been an error during control message transfer. (rlen = 9, was 0) > dvb-usb: error -5 while querying for an remote control event. > dvb-usb: bulk message failed: -32 (5/0) > ttusb2: there might have been an error during control message transfer. (rlen = 0, was 0) > dvb-usb: Technotrend TT-connect CT-3650 successfully initialized and connected. > Creating /dev/dvb/adapter0/demux0 > Creating /dev/dvb/adapter0/dvr0 > Creating /dev/input/event0 > dvb-usb: bulk message failed: -32 (4/0) > ttusb2: there might have been an error during control message transfer. (rlen = 9, was 0) > dvb-usb: error -5 while querying for an remote control event. > dvb-usb: bulk message failed: -32 (4/0) > > Are the error messages showstopper I have to solve first? > Well given the nature of your problems its pretty likely this is related... (Also there seems to be no /dev/dvb/adapter0/frontend0 created?) I have Cc'd Hans (maintainer of webcamd and the usb stack), maybe he has an idea? > > [...] HTH, Juergen
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20120421143156.GA36513>