Date: Thu, 09 Oct 2003 06:22:44 -0600 From: Scott Long <scottl@freebsd.org> To: Lauri Laupmaa <mauri@minut.ee> Cc: scsi@freebsd.org Subject: Re: Adaptec 2120S & 4.7-STABLE Message-ID: <3F855314.5020601@freebsd.org> In-Reply-To: <BB40F0BC-FA51-11D7-87F6-0003931E3224@minut.ee> References: <BB40F0BC-FA51-11D7-87F6-0003931E3224@minut.ee>
next in thread | previous in thread | raw e-mail | index | archive | help
Hi, Yes, the 'Optional battery present' message is wrong and I just haven't gotten around to fixing it. For your other problem, you need to remove the 'aacp' device from your kernel config. It's an option sub-device of aac and seems to cause many more problems than it's worth. Scott Lauri Laupmaa wrote: > Hi > > I have strange problem with aforementioned adaptec raid controller and > 4.7-STABLE. > The controller is detected by kernel, but for some awkward reason with > optional battery, which is not present actually (aaccli shows correct > info). The biggest problem, however, is that while system works from > ide drives and empty 2120S, it stops working (doesn't boot) when raid > disks are connected, the kernel just repeats last messaga: > aac0: **Monitor** SCSI bus reset issued on channel 0 > I have 3 other servers with 2120S, RAID5 and no IDE, all running 5.X. > > My questions: > a. Should 2120S work with 4.X and specifically with 4.7? > b. Could this be hardware problem? > c. Could this be firmware problem (my other 2120 controllers have Build > #5770 BIOS) > > TIA > L. > > Relevant info: > kernel: > bash-2.05a# uname -a > FreeBSD doall.blaah.com 4.7-STABLE FreeBSD 4.7-STABLE #6: Thu Nov 7 > 03:37:32 EET 2002 root@doall.blaah.com:/usr/obj/usr/src/sys/DOALL > i386 > > dmesg: > Copyright (c) 1992-2002 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > FreeBSD 4.7-STABLE #6: Thu Nov 7 03:37:32 EET 2002 > root@doall.codewiser.com:/usr/obj/usr/src/sys/DOALL > Timecounter "i8254" frequency 1193182 Hz > CPU: Pentium III/Pentium III Xeon/Celeron (863.87-MHz 686-class CPU) > Origin = "GenuineIntel" Id = 0x68a Stepping = 10 > > Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,C > MOV,PAT,PSE36,MMX,FXSR,SSE> > real memory = 536608768 (524032K bytes) > avail memory = 516874240 (504760K bytes) > Preloaded elf kernel "kernel" at 0xc051d000. > Pentium Pro MTRR support enabled > md0: Malloc disk > Using $PIR table, 12 entries at 0xc00f2ed0 > npx0: <math processor> on motherboard > npx0: INT 16 interface > pcib0: <Host to PCI bridge> on motherboard > pci0: <PCI bus> on pcib0 > pcib1: <Intel 82801BA/BAM (ICH2) PCI-PCI (AGP) bridge> at device 1.0 on > pci0 > pci2: <PCI bus> on pcib1 > pci2: <ATI Mach64-GM graphics accelerator> at 0.0 irq 11 > pcib2: <Intel 82801BA/BAM (ICH2) Hub to PCI bridge> at device 30.0 on pci0 > pci1: <PCI bus> on pcib2 > fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0xce80-0xcebf mem > 0xfc980000-0xfc99ffff,0xfc9ee000-0xfc9eefff irq 9 at device 9.0 on pci1 > fxp0: Ethernet address 00:02:b3:46:5a:8c > inphy0: <i82555 10/100 media interface> on miibus0 > inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto > fxp1: <Intel Pro 10/100B/100+ Ethernet> port 0xcf00-0xcf3f mem > 0xfc9c0000-0xfc9dffff,0xfc9ef000-0xfc9effff irq 4 at device 10.0 on pci1 > fxp1: Ethernet address 00:02:b3:8d:46:4b > inphy1: <i82555 10/100 media interface> on miibus1 > inphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto > aac0: <Adaptec SCSI RAID 2120S> mem 0xf0000000-0xf3ffffff irq 9 at > device 13.0 on pci1 > aac0: i960RX 100MHz, 48MB cache memory, optional battery present > aac0: Kernel 4.0-0, Build 6003, S/N b85172 > aacp0: <SCSI Passthrough Bus> on aac0 > isab0: <Intel 82801BA/BAM (ICH2) PCI to LPC bridge> at device 31.0 on pci0 > isa0: <ISA bus> on isab0 > atapci0: <Intel ICH2 ATA100 controller> port 0xffa0-0xffaf at device > 31.1 on pci0 > ata0: at 0x1f0 irq 14 on atapci0 > ata1: at 0x170 irq 15 on atapci0 > uhci0: <Intel 82801BA/BAM (ICH2) USB controller USB-A> port > 0xef40-0xef5f irq 7 at device 31.2 on pci0 > usb0: <Intel 82801BA/BAM (ICH2) USB controller USB-A> on uhci0 > usb0: USB revision 1.0 > uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub0: 2 ports with 2 removable, self powered > pci0: <unknown card> (vendor=0x8086, dev=0x2443) at 31.3 irq 10 > uhci1: <Intel 82801BA/BAM (ICH2) USB controller USB-B> port > 0xef80-0xef9f irq 3 at device 31.4 on pci0 > usb1: <Intel 82801BA/BAM (ICH2) USB controller USB-B> on uhci1 > usb1: USB revision 1.0 > uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub1: 2 ports with 2 removable, self powered > pci0: <unknown card> (vendor=0x8086, dev=0x2445) at 31.5 irq 10 > orm0: <Option ROMs> at iomem > 0xc0000-0xc7fff,0xc8000-0xcbfff,0xcc000-0xcd7ff,0xcd800-0xcefff on isa0 > fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0 > fdc0: FIFO enabled, 8 bytes threshold > fd0: <1440-KB 3.5" drive> on fdc0 drive 0 > atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 > sc0: <System console> at flags 0x100 on isa0 > sc0: VGA <16 virtual consoles, flags=0x300> > sio0: configured irq 4 not in bitmap of probed irqs 0 > sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 > sio0: type 8250 > sio1: configured irq 3 not in bitmap of probed irqs 0 > ppc0: parallel port not found. > ad0: 9773MB <FUJITSU MPF3102AT> [19857/16/63] at ata0-master UDMA66 > ad2: 38172MB <QUANTUM FIREBALLP AS40.0> [77557/16/63] at ata1-master > UDMA100 > ad3: 39266MB <IC35L040AVER07-0> [79780/16/63] at ata1-slave UDMA33 > acd0: CDROM <LTN526D> at ata0-slave PIO4 > Waiting 15 seconds for SCSI devices to settle > aac0: **Monitor** SCSI bus reset issued on channel 0 > aac0: **Monitor** PrintfToHost timeout > aac0: unknown command from controller > Mounting root from ufs:/dev/ad0s1a > > aacli: > AAC0> controller details > Executing: controller details > Controller Information > ---------------------- > Remote Computer: S > Device Name: S > Controller Type: No Info > Access Mode: READ-WRITE > Controller Serial Number: Last Six Digits = B85172 > Number of Buses: 1 > Devices per Bus: 15 > Controller CPU: i960 R series > Controller CPU Speed: 100 Mhz > Controller Memory: 64 Mbytes > Battery State: Not Present > > Component Revisions > ------------------- > CLI: 1.0-0 (Build #5263) > API: 1.0-0 (Build #5263) > Miniport Driver: 4.0-0 (Build #6003) > Controller Software: 4.0-0 (Build #6003) > Controller BIOS: 4.0-0 (Build #6003) > Controller Firmware: (Build #6003) > Controller Hardware: 2.64 > > _______________________________________________ > freebsd-scsi@freebsd.org mailing list > http://lists.freebsd.org/mailman/listinfo/freebsd-scsi > To unsubscribe, send any mail to "freebsd-scsi-unsubscribe@freebsd.org" >
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?3F855314.5020601>