Date: Wed, 2 Dec 1998 12:29:27 +0000 (GMT) From: freebsd-questions account <question@namodn.com> To: Chris Martino <chrismar@peanut.readington.com> Cc: freebsd-questions@FreeBSD.ORG Subject: Re: Sound.....again! (yamaha OPL3) Message-ID: <Pine.BSF.3.96.981202122718.9570F-100000@namodn.com> In-Reply-To: <Pine.BSF.3.96.981202151234.8300A-100000@peanut.readington.com>
next in thread | previous in thread | raw e-mail | index | archive | help
You should set it to 10 then, although i believe you can set it to what you like.. you would want to pnp 1 0 os enable (to let it know that you want to configure it rather than let your bios do it) pnp 1 0 irq0 10 etc, etc.. :) -rob ( www.namodn.com ) ( mailto : robert@namodn.com ) On Wed, 2 Dec 1998, Chris Martino wrote: > Ok... i'll leave it the way it is, how do I know what IRQ the card it at > also...it says 10 in the kernel config file because that is what is in > LINT. I took it straight outta there.. > > a cat /dev/sndstat shows: > > [chrismar@crazy ~ ] % cat /dev/sndstat > cat: /dev/sndstat: Device not configured > > Chris > > -- > > Chris Martino > chrismar@readington.com > > On Wed, 2 Dec 1998, freebsd-questions account wrote: > > > No, then you'd get pcm2 for your pnp device :) > > > > Leave it the way it is for now. > > > > When you get the boot prompt and type -c, don't go into visual mode. > > Type ls. At the bottom of the screen your pnp device should be > > configurable. > > ? will give you more help; just make sure it's enabled and stuff. > > > > Does doing cat /dev/sndstat at the regular ol' BSD prompt give you any > > useful output? I'm thinking maybe it's already assigned to pcm1... > > > > -rob > > ( www.namodn.com ) > > ( mailto : robert@namodn.com ) > > > > On Wed, 2 Dec 1998, Chris Martino wrote: > > > > > So, does that mean that I have to add > > > > > > device pcm1 at isa? port ? tty irq 10 drq 1 flags 0x0 vector pcmintr > > > > > > to my kernel config file and re-compile? > > > > > > Also, I'm not sure of what to type in the kernel config to turn on that > > > stuff you mentioned. > > > > > > Chris > > > > > > -- > > > > > > Chris Martino > > > chrismar@readington.com > > > > > > On Wed, 2 Dec 1998, freebsd-questions account wrote: > > > > > > > > > > > When you use plug n play cards with the pcm driver, the card uses the pcm1 > > > > device, not pcm0 (i know, i know :) although it does not seem that your > > > > card is assigned to pcm1.. > > > > > > > > Did you go into the kernel config (not visual!) and make sure the pnp > > > > settings are the way you want them? (enabled, irq, port, etc) > > > > > > > > One thing you must do when the card is pcm1, rm the /dev/audio, dsp, dspW, > > > > etc, and make new symlinks ln -s dsp1 dsp, audio1 audio, as opposed to the > > > > dsp -> dsp0 like before... > > > > > > > > Do a cat /dev/sndstat and see if the card is successfully detected as > > > > pcm1.. > > > > > > > > -rob > > > > ( www.namodn.com ) > > > > ( mailto : robert@namodn.com ) > > > > > > > > On Wed, 2 Dec 1998, Chris Martino wrote: > > > > > > > > > Over the last couple of days there has been a thread about the yamaha > > > > > OPL-SA sound card. I've followed the thread closely as I have a Yamaha > > > > > OPL3-SA3 sound board. > > > > > > > > > > Now, I followed the various hints to the T, and I'm still unable to get it > > > > > to work. Here is the stuff that I have so far theat seems the most > > > > > promising: > > > > > > > > > > In my kernel config: > > > > > controller pnp0 > > > > > device pcm0 at isa? port ? tty irq 10 drq 1 flags 0x0 vector pcmintr > > > > > > > > > > w/ that in there the dmesg shows: > > > > > Probing for PnP devices: > > > > > CSN 1 Vendor ID: YMH0800 [0x0008a865] Serial 0xffffffff > > > > > Probing for devices on the ISA bus: > > > > > sc0 at 0x60-0x6f irq 1 on motherboard > > > > > sc0: VGA color <16 virtual consoles, flags=0x0> > > > > > pcm0 not found at 0xffffffff > > > > > > > > > > Notice how it says it's not found...but I wonder why....what can I do do > > > > > make it found? > > > > > > > > > > I'll send the pnpinfo to anyone who wants it. > > > > > > > > > > I'm running FreeBSD 2.2.6. > > > > > > > > > > Any suggestions are GREATLY appreaciated. > > > > > > > > > > TIA, > > > > > Chris > > > > > > > > > > > > > > > > > > > > To Unsubscribe: send mail to majordomo@FreeBSD.org > > > > > with "unsubscribe freebsd-questions" in the body of the message > > > > > > > > > > > > > > > > > > > > > > > > > To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.BSF.3.96.981202122718.9570F-100000>