Date: Fri, 7 Aug 1998 20:39:11 -0400 (EDT) From: Spidey <beaupran@JSP.UMontreal.CA> To: Doug White <dwhite@resnet.uoregon.edu> Cc: Luigi Rizzo <luigi@labinfo.iet.unipi.it>, Questions=answers <freebsd-questions@FreeBSD.ORG> Subject: Re: 2.7: problems with Luigi pnp... Message-ID: <Pine.BSF.3.96.980807203300.7633A-100000@outpost.nada.org> In-Reply-To: <Pine.BSF.4.00.9808071329530.15104-100000@resnet.uoregon.edu>
next in thread | previous in thread | raw e-mail | index | archive | help
After all, it worked... I had to ./MAKEDEV snd1, and keep the 'pcm0' line... I still have strange output from reboot (dmesg -v): >>>>>>>>>>>>>>>>>>>>>> [snipped for sanity...] Probing for PnP devices: Trying Read_Port at 203 CSN 1 Vendor ID: CIR2000 [0x0020320d] Serial 0xffffffff CSN 2 Vendor ID: CTL0070 [0x70008c0e] Serial 0xffffffff PnP: override config for CSN 2 LDN 0 vend_id 0x70008c0e pnp2:0 port 0x0000 0x0000 0x0000 0x0000 irq 0:0 drq 4:4 en 0 fl 0x0 pnp2:0 port 0x0220 0x0330 0x0388 0x0000 irq 10:0 drq 1:5 en 1 fl 0x0 pnp2:0 port 0x0220 0x0330 0x0388 0x0000 irq 10:0 drq 1:5 en 1 fl 0x0 pcm1 (SB16pnp <SB16 PnP> sn 0xffffffff) at 0x220 irq 10 drq 1 flags 0x15 id 0 Probing for devices on the ISA bus: [snipped...] apm: found APM BIOS version 1.1 mss_probe: no address supplied, try default 0x530 mss_detect error, busy still set (0xff) sb_probe: no address supplied, try defaults (0x220,0x240) device at 0x220 already attached as unit 1 pcm0 not found at 0xffffffff imasks: bio c0084040, tty c00304ba, net c0060000 [snipped again...] wd0s4: type 0xa5, start 2056320, end = 3072383, size 1016064 : OK pid 333 (ee), uid 1000: exited on signal 11 (core dumped) pcm0: unit not configured, perhaps you want pcm1 ? 1 open: device busy 1 open: device busy 1 open: device busy timeout flushing dbuf_out, chan 1 cnt 0xccb4 flags 0x00000441 Luigi told me there was no reason to use pcm1 in my kernel, but I don't understand the output... And YES, I did rebuilt my kernel many times with many configuration, to the point of getting ones freezing!!! Goodbye! On Fri, 7 Aug 1998, Doug White wrote: > > On Thu, 6 Aug 1998, Spidey wrote: > > > > > I just upgraded from 2.2.6 to 2.2.7 release. In 2.6, I used the PnP > > > > controller and the pcm0 driver to enable my Sound Blaster 16 P'n p... Now > > > > it's not working anymore, even though I recompiled the kernel. > > > > > > > > This is dmesg: > > > > mss_probe: no address supplied, try default 0x530 > > > > mss_detect error, busy still set (0xff) > > > > sb_probe: no address supplied, try defaults (0x220,0x240) > > > > device at 0x220 already attached as unit 1 > > > ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ > > > > > > working OK as pcm1. Read your boot messages. > > > > Uh? I don't get it. Habitually, it gives me: > > sb at gnagnagna > > sbvxi at blahblah > > sbmidi at blah > > etc. > > > > Now it's shutting up! Why? > > You rebuilt your kernel? The pcm driver is new with 2.2.6. > > Doug White | University of Oregon > Internet: dwhite@resnet.uoregon.edu | Residence Networking Assistant > http://gladstone.uoregon.edu/~dwhite | Computer Science Major > > > To Unsubscribe: send mail to majordomo@FreeBSD.org > with "unsubscribe freebsd-questions" in the body of the message > Spidey How 'bout a little ride through your own world? http://www.JSP.UMontreal.CA/~beaupran/ To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.BSF.3.96.980807203300.7633A-100000>