Date: Fri, 15 Sep 2000 23:49:42 +0200 (CEST) From: =?ISO-8859-1?Q?G=E9rard_Roudier?= <groudier@club-internet.fr> To: Jaye Mathisen <mrcpu@internetcds.com> Cc: hackers@FreeBSD.ORG Subject: Re: SYM driver for Compaq 5500 Xeon? Message-ID: <Pine.LNX.4.10.10009152337130.1895-100000@linux.local> In-Reply-To: <Pine.BSF.4.21.0009151411160.290-100000@apocalypse.cdsnet.net>
next in thread | previous in thread | raw e-mail | index | archive | help
On Fri, 15 Sep 2000, Jaye Mathisen wrote: > This is with the 4.1 boot floppies. But the drives don't show. I'm > booting -v now to see. >=20 > Just did, still no drives. Nothing extraordinary in the -v output. >=20 > it's a compaq PROLIANT, 5500, quad xeon, 1.25GB of RAM, 2 9GB scsi disks > on ID's 0 and 1 of the only controller. >=20 > bootloader sees them just fine. The bootloader uses the BIOS. > I don't know much about hot-plug stuff, it looks relatively normal to me, > and it's an older rev. That's about it. If you mean that the disks are hot-pluggable, then it could be the SCSI device that allows to control the hot-plug bay that makes problem during the scan of the SCSI BUS. If there is some way to desactivate this 'for now hypothetical device' or to update its firmware, you should try either. > My adaptec suggestion was only because perhaps the driver wasn't > integrated until after the floppies were made, so I could get installed, > then update the kernel. No problem here, if it works with Adaptec. Nobody wants to waste one's time. I just wanted to say that this also may apply in the reverse direction. Regards, G=E9rard. > I guess I"ll try that route, but I'd rather not. >=20 > On Fri, 15 Sep 2000, [ISO-8859-1] G=E9rard Roudier wrote: >=20 > >=20 > >=20 > > On Fri, 15 Sep 2000, Jaye Mathisen wrote: > >=20 > > > Compaq Proliant 5500, with the on-board NCR SCSI: > > >=20 > > > I get: > > >=20 > > > pci0: <unknown card> (vendor=3D0x0e11, dev=3D0xa0f0) > > > sym0: <875> port blahblah > > > sym0: no NVRAM, ID 7, Fast-20, SE, parity-checking > > >=20 > > >=20 > > > And the same for sym1. > > >=20 > > >=20 > > > What's the magic incantation to make this work? Or do I need to use = an > > > adaptect to get installed, then update to -stable or somesuch? > >=20 > > You seemed to say that your hard disks are not discovered in another > > email (I didn't see it but saw a reply to it). > >=20 > > Could you describe the machine ? > > Does it have a some hot-plug backplane, for example ? > > What FreeBSD version ? > >=20 > > About trying to install the system using an Adaptec, why not ? > > (Btw, it also happen that using a Symbios device sometimes cures a fail= ing > > system that used an Adaptec controller). > >=20 > > G=E9rard. To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-hackers" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.LNX.4.10.10009152337130.1895-100000>