Skip site navigation (1)Skip section navigation (2)
Date:      Fri, 11 Apr 2003 00:26:27 +0200
From:      Erik Trulsson <ertr1013@student.uu.se>
To:        John Baldwin <jhb@FreeBSD.org>
Cc:        freebsd-hackers@freebsd.org
Subject:   Re: Anyone seen 4.8-RELEASE running on a real 386 (not 486 586 etc) ?
Message-ID:  <20030410222627.GA65278@falcon.midgard.homeip.net>
In-Reply-To: <XFMail.20030410163458.jhb@FreeBSD.org>
References:  <20030410193810.GA52024@falcon.midgard.homeip.net> <XFMail.20030410163458.jhb@FreeBSD.org>

next in thread | previous in thread | raw e-mail | index | archive | help
On Thu, Apr 10, 2003 at 04:34:58PM -0400, John Baldwin wrote:
> 
> On 10-Apr-2003 Erik Trulsson wrote:
> > On Thu, Apr 10, 2003 at 08:43:04PM +0200, Julian Stacey wrote:
> >> freebsd-hackers@,
> >> Anyone seen 4.8-RELEASE running on a real 386 processor (not a 486, 586 etc) ?
> >> 
> >> I have a 386 that runs 4.7, dmesg below, both GENERIC & my own kernel;
> >> But it wont boot 4.8 { either generic or my own config } compiled on my
> >> other 4.8 box.  I tried making with & without /etc/make.conf
> >>      CFLAGS =        -m386 -march=i386 -msoft-float -mcpu=i386 -O -pipe
> >>      COPTFLAGS=      -m386 -march=i386 -msoft-float -mcpu=i386 -O -pipe
> >> I tried the /kernel copied from a 4.8 cdrom to hard disk (no cdrom
> >> drive on the box).  I tried 4.8 boot floppies (to prove its not
> >> something wrong in hard disc /boot) Every 4.8 kernel crashes during boot -s.
> >> 
> >> This 386 box is no bigger than a book, so worth persevering :-)
> >> "SX 33" is written on chip, though dmesg reports "DX".
> >> 
> >> I recall 386 support was dropped in 5.0, but presume not dropped in 4.8,
> >> ( I don't see any signs in /usr/share/mk comparing 4.7 & 4.8 )
> >> The 4.8 cdrom /[A-Z]* files say i386 is still supported.
> >> 
> >> I removed the only card in the box (a 3com ISA ethernet jumperless) - 
> >> it still wouldnt boot, so put ethernet card back in, as not the problem.
> >> 
> >> I compiled a kernel with ddb,  Results copied by hand as no serial for
> >> remote gdb.t present
> >> 
> >> Ideas or solutions anyone ?
> >> 
> >> 4.8 ddb:
> >>    Fatal trap 1: priveleged instruction fault while in kernel mode
> >>    instruction pointer = 0x8:0xc02695a0
> >>    stack pointewr      = 0x10:0xc0379fcc
> >>    frame pointer       = 0x10:0xc0379fcc
> >>    code segment          = base 0x0, limit 0xfffff, type 0x1b
> >>                  = DPL 0, pres 1, def 32 1, gran 1
> >>    processor eflags    = interrupt enabled, resume, IOPL = 0
> >>    current process     = Idle
> >>    interrupt mask      = net tty bio cam
> >>    kernel: type 1 trap, code=0
> >>    stopped at 0xc02695a0:     invlpg  0(%ecx)
> > 
> > Try the following patch.
> > Makes my 386sx/33 work fine at least.
> > (Without it I get the same panic as you do.)
> 
> Oh my, I hope that isn't it.  If so it's my fault. :(
> 
> Hmm, can you try this patch instead?
> 
> http://www.FreeBSD.org/~jhb/patches/4x_386.patch

That patch does not work for me.
The patch I posted earlier does work for me.

(Reverting identcpu.c to 1.80.2.13 also works but that seems
a bit ... excessive IMO.)


-- 
<Insert your favourite quote here.>
Erik Trulsson
ertr1013@student.uu.se



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20030410222627.GA65278>