Date: Sat, 23 Aug 1997 00:11:58 -0700 (PDT) From: Alex <garbanzo@hooked.net> To: Daniel Unruh <unruh@informatik.uni-freiburg.de> Cc: aic7xxx@FreeBSD.ORG Subject: Re: ``Unexpected busfree'' with 2.1.51 Message-ID: <Pine.BSF.3.96.970823001141.236A-100000@zippy.dyn.ml.org> In-Reply-To: <XFMail.970823084201.unruh@informatik.uni-freiburg.de>
next in thread | previous in thread | raw e-mail | index | archive | help
On Sat, 23 Aug 1997, Daniel Unruh wrote: > When booting 2.1.51, the kernel hangs during SCSI device detection: > > [...] > scsi target 3 [...] refusing wide [...] > (scsi0:3:0) Reset device active_scb 0 > scsi0: (targ 3, chan A) matching scb to (targ 3/chan A) > scsi0: (targ 3, chan A) matching scb to (targ 3/chan A) > scsi0: Unexpected busfree, LASTPHASE=0xe0, SEQADDR=0x4f > > Then it spews out kernel debug messages and reboots. > > > > Hardware: Gigabyte GA-586DX w/ onboard AIC7880. > > Compile Options: > AIC7XXX_RESET_DELAY : 15 > AIC7XXX_TAGGED_QUEUEING: Enabled > AIC7XXX_PAGE_ENABLE : Enabled > AIC7XXX_PROC_STATS : Disabled > > Adapter Configuration: > SCSI Adapter: Adaptec AIC-7880 Ultra SCSI host adapter > (AIC-788x chipset) > Host Bus: Wide > Base IO: 0x6200 > Base IO Memory: 0xe0804000 > IRQ: 9 > SCBs: Used 1, HW 16, Page 255 > Interrupts: 94 > Serial EEPROM: True > Extended Translation: Enabled > SCSI Bus Reset: Disabled > Ultra SCSI: Enabled > Target Disconnect: Enabled > > Attached devices: > Host: scsi0 Channel: 00 Id: 02 Lun: 00 > Vendor: TOSHIBA Model: CD-ROM XM-5301TA Rev: 0925 > Type: CD-ROM ANSI SCSI revision: 02 > Host: scsi0 Channel: 00 Id: 03 Lun: 00 > Vendor: SEAGATE Model: ST43400N Rev: 1028 > Type: Direct-Access ANSI SCSI revision: 02 > Host: scsi0 Channel: 00 Id: 04 Lun: 00 > Vendor: TANDBERG Model: TDC 3800 Rev: =04: > Type: Sequential-Access ANSI SCSI revision: 02 > Host: scsi0 Channel: 00 Id: 05 Lun: 00 > Vendor: IMS Model: CDD2000/00 Rev: 1.26 > Type: CD-ROM ANSI SCSI revision: 02 > Host: scsi0 Channel: 00 Id: 12 Lun: 00 > Vendor: IBM Model: DCAS-34330W Rev: S61A > Type: Direct-Access ANSI SCSI revision: 02 > > > > Turning on/off tagged queueing, paging and scsi bios does not help. > Disconnecting the Seagate fixes the problem. > > 2.0.30 runs just fine. > > Is there anything I can do to get the driver running? Have you tried updating the firmware on the Segate? - alex
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.BSF.3.96.970823001141.236A-100000>