Date: Sun, 8 Jul 2001 15:39:19 +0200 From: Eelke Blok <e.blok@student.utwente.nl> To: freebsd-multimedia@freebsd.org Subject: Getting Pinnacle PCTV Pro to work Message-ID: <01070815391903.00338@hotrod>
next in thread | raw e-mail | index | archive | help
Hi all, I tried to find the answer to my question on the web, but couldn't find it. I am having some trouble getting my Pinnacle PCTV Pro TV-card to work in FreeBSD with fxtv. All I get from fxtv is a blue screen. Channel change works in that the OSD displays a channel identifier and a frequency when pushing the buttons. I also get a click on start-up of fxtv and some faint noise from the speakers the (but nowhere near as loud as a mistuned channel, it basically sounds as though something was "turned on"). The version of FXTV I'm using is 1.02. I copied over a configuration file from a friend in the same building, which means at least the channels and frequencies should be OK. I wanted to check any other options in there, but I can't find where the config file is supposed to be (neither in the documentation to fxtv nor using find). You can probably tell I am a total newbie, so don't be too hard on me :) Here's my dmesg output, if it's any use: --- Copyright (c) 1992-2001 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 4.3-STABLE #5: Thu Jun 28 21:15:37 CEST 2001 eelke@hotrod:/usr/obj/usr/src/sys/HOTROD Timecounter "i8254" frequency 1193182 Hz Timecounter "TSC" frequency 706294477 Hz CPU: AMD Athlon(tm) Processor (706.29-MHz 686-class CPU) Origin = "AuthenticAMD" Id = 0x642 Stepping = 2 Features=0x183f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR> AMD Features=0xc0440000<<b18>,AMIE,DSP,3DNow!> real memory = 268353536 (262064K bytes) config> di sn0 No such device: sn0 Invalid command or syntax. Type `?' for help. config> di lnc0 No such device: lnc0 Invalid command or syntax. Type `?' for help. config> di ie0 No such device: ie0 Invalid command or syntax. Type `?' for help. config> di fe0 No such device: fe0 Invalid command or syntax. Type `?' for help. config> di ed0 config> di cs0 No such device: cs0 Invalid command or syntax. Type `?' for help. config> q avail memory = 258445312 (252388K bytes) Preloaded elf kernel "kernel" at 0xc02d6000. Preloaded userconfig_script "/boot/kernel.conf" at 0xc02d609c. Pentium Pro MTRR support enabled npx0: <math processor> on motherboard npx0: INT 16 interface pcib0: <Host to PCI bridge> on motherboard pci0: <PCI bus> on pcib0 pcib2: <PCI to PCI bridge (vendor=1106 device=8305)> at device 1.0 on pci0 pci1: <PCI bus> on pcib2 pci1: <Matrox MGA G400 AGP graphics accelerator> at 0.0 irq 11 isab0: <VIA 82C686 PCI-ISA bridge> at device 4.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <VIA 82C686 ATA66 controller> port 0xd800-0xd80f at device 4.1 on pci0 ata0: at 0x1f0 irq 14 on atapci0 ata1: at 0x170 irq 15 on atapci0 pci0: <VIA 83C572 USB controller> at 4.2 irq 9 pci0: <VIA 83C572 USB controller> at 4.3 irq 9 pcm0: <Creative EMU10K1> port 0xa400-0xa41f irq 9 at device 9.0 on pci0 ed0: <NE2000 PCI Ethernet (ProLAN)> port 0x9800-0x981f irq 5 at device 10.0 on pci0 ed0: address 00:40:95:01:8c:84, type NE2000 (16 bit) bktr0: <BrookTree 878> mem 0xe1000000-0xe1000fff irq 9 at device 13.0 on pci0 iicbb0: <I2C generic bit-banging driver> on bti2c0 iicbus0: <Philips I2C bus> on iicbb0 master-only smbus0: <System Management Bus> on bti2c0 bktr0: Detected a MSP3451G-A2 at 0x80 bktr0: Pinnacle/Miro TV, Temic PAL tuner, msp3400c stereo. pci0: <unknown card> (vendor=0x109e, dev=0x0878) at 13.1 irq 9 atapci1: <Promise ATA100 controller> port 0x8000-0x803f,0x8400-0x8403,0x8800-0x8807,0x9000-0x9003,0x9400-0x9407 mem 0xde800000-0xde81ffff irq 10 at device 17.0 on pci0 pcib1: <Host to PCI bridge> on motherboard pci2: <PCI bus> on pcib1 orm0: <Option ROM> at iomem 0xc0000-0xc7fff on isa0 fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0 fdc0: FIFO enabled, 8 bytes threshold fd0: <1440-KB 3.5" drive> on fdc0 drive 0 atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 kbd0 at atkbd0 psm0: <PS/2 Mouse> irq 12 on atkbdc0 psm0: model MouseMan+, device ID 0 vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 16550A sio1 at port 0x2f8-0x2ff irq 3 on isa0 sio1: type 16550A ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0 ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode ppc0: FIFO with 16/16/8 bytes threshold lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port ad0: 19574MB <WDC WD205BA> [39770/16/63] at ata0-master UDMA66 acd0: CD-RW <PLEXTOR CD-R PX-W8432T> at ata1-master using PIO4 acd1: CDROM <CD-ROM 36X/AKW> at ata1-slave using PIO4 Mounting root from ufs:/dev/ad0s3a ad0s2: raw partition size != slice size ad0s2: start 3148740, end 33527654, size 30378915 ad0s2c: start 3148740, end 6265349, size 3116610 uhci0: <VIA 83C572 USB controller> port 0xd400-0xd41f irq 9 at device 4.2 on pci0 usb0: <VIA 83C572 USB controller> on uhci0 usb0: USB revision 1.0 uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered uhci1: <VIA 83C572 USB controller> port 0xd000-0xd01f irq 9 at device 4.3 on pci0 usb1: <VIA 83C572 USB controller> on uhci1 usb1: USB revision 1.0 uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub1: 2 ports with 2 removable, self powered --- Any help would be very much appreciated. Cheers, Eelke To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-multimedia" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?01070815391903.00338>