Date: Sat, 17 Jan 2004 19:29:12 +0100 From: Ben Stuyts <ben@stuyts.nl> To: current@FreeBSD.org Cc: pdeuskar@FreeBSD.org Subject: em0 watchdog reset (kern/60285) Message-ID: <0C23C66F-491B-11D8-A06B-000A959CFF76@stuyts.nl>
next in thread | raw e-mail | index | archive | help
Hi, I am trying to setup -current (just cvsupped) on a Gigabyte GA-8KNXP and I experience the same symptoms as mentioned in the PR in the subject: em0 keeps getting watchdog resets, and is unusable. (http://www.freebsd.org/cgi/query-pr.cgi?pr=kern%2F60285) It seems there is an acpi problem, which might be related. (pcib2: could not get PCI interrupt routing table for \\_SB_.PCI0.CSAB - AE_NOT_FOUND) Is there something I can do to help solve the problem? Here is a dmesg, using the GENERIC kernel: Copyright (c) 1992-2004 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 5.2-CURRENT #1: Sat Jan 17 18:19:48 CET 2004 root@aurora.stuyts.nl:/mnt2/obj/home/src/sys/GENERIC Preloaded elf kernel "/boot/kernel/kernel" at 0xc0a83000. Preloaded elf module "/boot/kernel/acpi.ko" at 0xc0a831f4. Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: Intel(R) Pentium(R) 4 CPU 2.40GHz (2411.61-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0xf29 Stepping = 9 Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE ,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> Hyperthreading: 2 logical CPUs real memory = 536805376 (511 MB) avail memory = 515579904 (491 MB) ACPI APIC Table: <GBT AWRDACPI> FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs cpu0 (BSP): APIC ID: 0 cpu1 (AP): APIC ID: 1 ioapic0: Changing APIC ID to 2 ioapic0 <Version 2.0> irqs 0-23 on motherboard Pentium Pro MTRR support enabled npx0: [FAST] npx0: <math processor> on motherboard npx0: INT 16 interface acpi0: <GBT AWRDACPI> on motherboard pcibios: BIOS version 2.10 Using $PIR table, 15 entries at 0xc00fd440 acpi0: Power Button (fixed) Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0 acpi_cpu0: <CPU> on acpi0 acpi_cpu1: <CPU> on acpi0 acpi_button0: <Power Button> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0x1000-0x10bf,0xcf8-0xcff on acpi0 pci0: <ACPI PCI bus> on pcib0 agp0: <Intel 82875P host to AGP bridge> mem 0xe8000000-0xefffffff at device 0.0 on pci0 pcib1: <PCI-PCI bridge> at device 1.0 on pci0 pci1: <PCI bus> on pcib1 pcib1: slot 0 INTA is routed to irq 16 pci1: <display, VGA> at device 0.0 (no driver attached) pcib2: <ACPI PCI-PCI bridge> at device 3.0 on pci0 pcib2: could not get PCI interrupt routing table for \\_SB_.PCI0.CSAB - AE_NOT_FOUND pci2: <ACPI PCI bus> on pcib2 em0: <Intel(R) PRO/1000 Network Connection, Version - 1.7.19> port 0xa000-0xa01f mem 0xfa000000-0xfa01ffff irq 11 at device 1.0 on pci2 em0: Speed:N/A Duplex:N/A uhci0: <Intel 82801EB (ICH5) USB controller USB-A> port 0xb000-0xb01f irq 16 at device 29.0 on pci0 usb0: <Intel 82801EB (ICH5) USB controller USB-A> on uhci0 usb0: USB revision 1.0 uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered uhci1: <Intel 82801EB (ICH5) USB controller USB-B> port 0xb400-0xb41f irq 19 at device 29.1 on pci0 usb1: <Intel 82801EB (ICH5) USB controller USB-B> on uhci1 usb1: USB revision 1.0 uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub1: 2 ports with 2 removable, self powered ums0: A4Tech USB Optical Mouse, rev 1.10/0.01, addr 2, iclass 3/1 ums0: 7 buttons and Z dir. uhci2: <Intel 82801EB (ICH5) USB controller USB-C> port 0xb800-0xb81f irq 18 at device 29.2 on pci0 usb2: <Intel 82801EB (ICH5) USB controller USB-C> on uhci2 usb2: USB revision 1.0 uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub2: 2 ports with 2 removable, self powered uhci3: <Intel 82801EB (ICH5) USB controller USB-D> port 0xbc00-0xbc1f irq 16 at device 29.3 on pci0 usb3: <Intel 82801EB (ICH5) USB controller USB-D> on uhci3 usb3: USB revision 1.0 uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub3: 2 ports with 2 removable, self powered pci0: <serial bus, USB> at device 29.7 (no driver attached) pcib3: <ACPI PCI-PCI bridge> at device 30.0 on pci0 pci3: <ACPI PCI bus> on pcib3 fwohci0: <Texas Instruments TSB43AB23> mem 0xfa100000-0xfa103fff,0xfa104000-0xfa1047ff irq 22 at device 10.0 on pci3 fwohci0: OHCI version 1.10 (ROM=1) fwohci0: No. of Isochronous channel is 4. fwohci0: EUI64 00:20:ed:0a:00:86:78:40 fwohci0: Phy 1394a available S400, 3 ports. fwohci0: Link S400, max_rec 2048 bytes. firewire0: <IEEE1394(FireWire) bus> on fwohci0 fwe0: <Ethernet over FireWire> on firewire0 if_fwe0: Fake Ethernet address: 02:20:ed:86:78:40 sbp0: <SBP-2/SCSI over FireWire> on firewire0 fwohci0: Initiate bus reset fwohci0: BUS reset fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me) firewire0: bus manager 0 (me) isab0: <PCI-ISA bridge> at device 31.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <Intel ICH5 UDMA100 controller> port 0xf000-0xf00f,0-0x3,0-0x7,0-0x3,0-0x7 at device 31.1 on pci0 ata0: at 0x1f0 irq 14 on atapci0 ata0: [MPSAFE] ata1: at 0x170 irq 15 on atapci0 ata1: [MPSAFE] atapci1: <Intel ICH5 SATA150 controller> port 0xd000-0xd00f,0xcc00-0xcc03,0xc800-0xc807,0xc400-0xc403,0xc000-0xc007 irq 18 at device 31.2 on pci0 atapci1: [MPSAFE] ata2: at 0xc000 on atapci1 ata2: [MPSAFE] ata3: at 0xc800 on atapci1 ata3: [MPSAFE] pci0: <serial bus, SMBus> at device 31.3 (no driver attached) pci0: <multimedia, audio> at device 31.5 (no driver attached) fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on acpi0 fdc0: FIFO enabled, 8 bytes threshold fd0: <1440-KB 3.5" drive> on fdc0 drive 0 sio0 port 0x3f8-0x3ff irq 4 on acpi0 sio0: type 16550A sio1 port 0x2f8-0x2ff irq 3 on acpi0 sio1: type 16550A ppc0 port 0x378-0x37f irq 7 on acpi0 ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode ppbus0: <Parallel port bus> on ppc0 plip0: <PLIP network interface> on ppbus0 lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port ppi0: <Parallel I/O> on ppbus0 atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0 atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 kbd0 at atkbd0 orm0: <Option ROMs> at iomem 0xd0000-0xd7fff,0xc0000-0xccfff on isa0 pmtimer0 on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 Timecounters tick every 10.000 msec GEOM: create disk ad0 dp=0xc4588c60 ad0: 117246MB <Maxtor 6Y120L0> [238216/16/63] at ata0-master UDMA100 GEOM: create disk ad2 dp=0xc4588a60 ad2: 117246MB <Maxtor 6Y120L0> [238216/16/63] at ata1-master UDMA100 acd0: DVDROM <HL-DT-STDVD-ROM GDR8161B> at ata1-slave PIO4 SMP: AP CPU #1 Launched! Mounting root from ufs:/dev/ad0s1a em0: Link is up 100 Mbps Full Duplex em0: watchdog timeout -- resetting em0: Link is up 100 Mbps Full Duplex em0: watchdog timeout -- resetting em0: Link is up 100 Mbps Full Duplex em0: watchdog timeout -- resetting em0: Link is up 100 Mbps Full Duplex em0: watchdog timeout -- resetting em0: Link is up 100 Mbps Full Duplex Kind regards, Ben
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?0C23C66F-491B-11D8-A06B-000A959CFF76>