Date: Fri, 17 Oct 2003 14:16:56 +0800 From: Joel Adams <joel@perthradclinic.com.au> To: freebsd-scsi@freebsd.org Subject: Adaptec 2120S problem Message-ID: <1066371416.3f8f89581c6ae@dao.perthradclinic.com.au>
next in thread | raw e-mail | index | archive | help
Hi, I've been running a new server with 4.8-RELEASE-p13 for the past week, and it's been fine, until this morning where I've had the same SCSI error twice. Once it comes, the system is basically unusable (you can't ssh in) and needs a hard boot. An example error: aac0: COMMAND 0x342622c TIMEOUT AFTER 34 SECONDS This is the error, and it continually repeated, although the command and timeout values change. Does anyone have any idea what this means? I have not built my kernel with aacp. Latest controller firmware has been installed. The power supplies seem OK. Any help would be much appreciated. Thanks, -Joel. Copyright (c) 1992-2003 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 4.8-RELEASE-p13 #0: Sat Oct 11 13:55:56 WST 2003 root@dao.perthradclinic.com.au:/usr/obj/usr/src/sys/DAO Timecounter "i8254" frequency 1193182 Hz CPU: Intel(R) Xeon(TM) CPU 2.40GHz (2392.30-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0xf27 Stepping = 7 Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> Hyperthreading: 2 logical CPUs real memory = 1073676288 (1048512K bytes) avail memory = 1039929344 (1015556K bytes) Programming 24 pins in IOAPIC #0 IOAPIC #0 intpin 2 -> irq 0 Programming 24 pins in IOAPIC #1 Programming 24 pins in IOAPIC #2 FreeBSD/SMP: Multiprocessor motherboard cpu0 (BSP): apic id: 0, version: 0x00050014, at 0xfee00000 cpu1 (AP): apic id: 1, version: 0x00050014, at 0xfee00000 cpu2 (AP): apic id: 6, version: 0x00050014, at 0xfee00000 cpu3 (AP): apic id: 7, version: 0x00050014, at 0xfee00000 io0 (APIC): apic id: 8, version: 0x00178020, at 0xfec00000 io1 (APIC): apic id: 9, version: 0x00178020, at 0xfec81000 io2 (APIC): apic id: 10, version: 0x00178020, at 0xfec81400 Preloaded elf kernel "kernel" at 0xc04fc000. Pentium Pro MTRR support enabled md0: Malloc disk Using $PIR table, 19 entries at 0xc00f2f10 npx0: <math processor> on motherboard npx0: INT 16 interface pcib0: <Host to PCI bridge> on motherboard IOAPIC #0 intpin 16 -> irq 2 IOAPIC #0 intpin 19 -> irq 16 pci0: <PCI bus> on pcib0 pci0: <unknown card> (vendor=0x8086, dev=0x2541) at 0.1 pcib1: <PCI to PCI bridge (vendor=8086 device=2545)> at device 3.0 on pci0 pci2: <PCI bus> on pcib1 pci2: <unknown card> (vendor=0x8086, dev=0x1461) at 28.0 pcib2: <PCI to PCI bridge (vendor=8086 device=1460)> at device 29.0 on pci2 IOAPIC #2 intpin 2 -> irq 18 IOAPIC #2 intpin 1 -> irq 19 pci4: <PCI bus> on pcib2 ahd0: <adaptec AIC7902 Ultra320 SCSI adapter> port 0x4000-0x40ff,0x3800-0x38ff mem 0xfe9e0000-0xfe9e1fff irq 18 at device 7.0 on pci4 aic7902: Ultra320 Wide Channel A, SCSI Id=7, PCI-X 67-100Mhz, 512 SCBs ahd1: <adaptec AIC7902 Ultra320 SCSI adapter> port 0x3400-0x34ff,0x3000-0x30ff mem 0xfe9f0000-0xfe9f1fff irq 19 at device 7.1 on pci4 aic7902: Ultra320 Wide Channel B, SCSI Id=7, PCI-X 67-100Mhz, 512 SCBs pci2: <unknown card> (vendor=0x8086, dev=0x1461) at 30.0 pcib3: <PCI to PCI bridge (vendor=8086 device=1460)> at device 31.0 on pci2 IOAPIC #1 intpin 6 -> irq 20 IOAPIC #1 intpin 7 -> irq 21 IOAPIC #1 intpin 3 -> irq 22 pci3: <PCI bus> on pcib3 em0: <Intel(R) PRO/1000 Network Connection, Version - 1.4.10> port 0x2040-0x207f mem 0xfe6a0000-0xfe6bffff irq 20 at device 7.0 on pci3 em0: Speed:100 Mbps Duplex:Full em1: <Intel(R) PRO/1000 Network Connection, Version - 1.4.10> port 0x2000-0x203f mem 0xfe6c0000-0xfe6dffff irq 21 at device 7.1 on pci3 em1: Speed:N/A Duplex:N/A aac0: <adaptec SCSI RAID 2120S> mem 0xf8000000-0xfbffffff irq 22 at device 9.0 on pci3 aac0: i960RX 100MHz, 48MB cache memory, optional battery present aac0: Kernel 4.0-0, Build 6008, S/N b82d7d pci0: <unknown card> (vendor=0x8086, dev=0x2546) at 3.1 uhci0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> port 0x5020-0x503f irq 2 at device 29.0 on pci0 usb0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> on uhci0 usb0: USB revision 1.0 uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered uhci1: <Intel 82801CA/CAM (ICH3) USB controller USB-B> port 0x5000-0x501f irq 16 at device 29.1 on pci0 usb1: <Intel 82801CA/CAM (ICH3) USB controller USB-B> on uhci1 usb1: USB revision 1.0 uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub1: 2 ports with 2 removable, self powered pcib4: <Intel 82801BA/BAM (ICH2) Hub to PCI bridge> at device 30.0 on pci0 pci1: <PCI bus> on pcib4 pci1: <aTI Mach64-GR graphics accelerator> at 12.0 irq 17 isab0: <PCI to ISA bridge (vendor=8086 device=2480)> at device 31.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <Intel ICH3 ATA100 controller> port 0x3a0-0x3af,0-0x3,0-0x7,0-0x3,0-0x7 irq 0 at device 31.1 on pci0 ata0: at 0x1f0 irq 14 on atapci0 ata1: at 0x170 irq 15 on atapci0 pci0: <unknown card> (vendor=0x8086, dev=0x2483) at 31.3 irq 17 orm0: <Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xcbfff,0xcc000-0xcd7ff,0xcd800-0xcefff on isa0 fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0 fdc0: FIFO enabled, 8 bytes threshold fd0: <1440-KB 3.5" drive> on fdc0 drive 0 atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 atkbd0: <aT Keyboard> flags 0x1 irq 1 on atkbdc0 kbd0 at atkbd0 vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 16550A sio1 at port 0x2f8-0x2ff irq 3 on isa0 sio1: type 16550A ppc0: parallel port not found. APIC_IO: Testing 8254 interrupt delivery APIC_IO: routing 8254 via IOAPIC #0 intpin 2 SMP: AP CPU #2 Launched! SMP: AP CPU #3 Launched! SMP: AP CPU #1 Launched! acd0: CDROM <SAMSUNG CD-ROM SN-124> at ata1-master PIO4 Waiting 15 seconds for SCSI devices to settle aacd0: <RAID 1 (Mirror)> on aac0 aacd0: 34998MB (71677440 sectors) aacd1: <RAID 1 (Mirror)> on aac0 aacd1: 70006MB (143372544 sectors) Mounting root from ufs:/dev/aacd0s1a WARNING: / was not properly dismounted
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?1066371416.3f8f89581c6ae>