Date: Wed, 13 Apr 2005 20:49:24 -0400 From: Stephan Uphoff <ups@tree.com> To: "M. Parsons" <mrparsons@gmail.com> Cc: freebsd-hackers@freebsd.org Subject: Re: Route/arp help? Message-ID: <1113439764.7457.55947.camel@palm> In-Reply-To: <ac8741ae05041313384be3e17@mail.gmail.com> References: <ac8741ae050413102521d1aac7@mail.gmail.com> <ac8741ae05041313384be3e17@mail.gmail.com>
next in thread | previous in thread | raw e-mail | index | archive | help
On Wed, 2005-04-13 at 16:38, M. Parsons wrote: > On 4/13/05, Iasen Kostov <tbyte@otel.net> wrote: > > M. Parsons wrote: > > > > >To access my dsl modem's line stats page, I have to create an arp > > >entry and a route for it, under linux this was done as: (eth1 > > >connected directly to dsl modem) > > > > > >ifconfig eth1 10.0.0.2 netmask 255.255.255.0 > > >route add 10.0.0.1 dev eth1 > > > > > > > > route add -net 10.0.0.1/32 -iface de0 -cloning > > > > But 'ifconfig de0 10.0.0.2 netmask 255.255.255.0' (or ifconfig de0 > > 10.0.0.2/24) should set a 10.0.0.0/24 route via de0 why would you want > > to set it again ? > > > > >arp -s 10.0.0.1 ffffffffffffffffff (not really fffff, but the MAC > > >address of the dsl modem, NOT the nic). > > > > > >unfortunately, I cant seem to figure out the commands to get this to > > >work under FreeBSD 5.3 > > > > > >Ifconfig is simple enough (replace eth1 with de0 in my case) > > > > > >Arp seems the same (except it needs colons) > > > > > >But the route command I have no clue. It doesnt seem to follow the > > >same syntax as linux, and I havent figured out the correct syntax yet. > > > > > >Any help? > > > > > >Thanks, > > > > > >Mark > > > Honestly I have no clue why its not working, it should be simple, but > it isnt.. Here is what the arp cache shows and the routing table (and > its ed0, not de0, my mistake in original message). > > arp: (after doing the arp -s command) > > modem (10.0.0.1) at 00:0b:23:2a:b0:c4 on ed0 permanent [ethernet] > > this looks right doesnt it? > > route: > > default mydslgateway UGS 0 8173 tun0 > 10/24 link#1 UC 0 0 ed0 > modem 00:0b:23:2a:b0:c4 UHLS 0 4 ed0 => > 10.0.0.1/32 link#1 UCS 0 0 ed0 > > no idea here? 3 for ed0? is that right? > > note, ed0 is also creating the tun0 device (pppoe), but that was never > a problem in linux. I was under the impression (but would need to check to make sure) that all incoming packets are diverted to ng_pppoe when it is hooked into the Ethernet interface. This would explain your problems. Can you try this without the interface being used for PPPOE? > > Im just confused. :( > > Its not a big deal, as its only my dsl line stats, but still confused > why it aint working > > For the record, http://www.broadbandreports.com/faq/9693 is the page > on how you access the line stats, and the MAC part is required for my > modem. > > Thanks for all the help > > Mark > _______________________________________________ > freebsd-hackers@freebsd.org mailing list > http://lists.freebsd.org/mailman/listinfo/freebsd-hackers > To unsubscribe, send any mail to "freebsd-hackers-unsubscribe@freebsd.org" > >
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?1113439764.7457.55947.camel>