Date: Mon, 30 Jun 2008 23:37:09 +0100 From: Craig Butler <craig001@lerwick.hopto.org> To: freebsd-sparc64@freebsd.org Subject: installing freebsd on b100 blade -- STUCK !! Message-ID: <1214865429.1501.6.camel@main.lerwick.hopto.org>
next in thread | raw e-mail | index | archive | help
Hi Guys,
Am stuck trying to install FreeBSD 7 on a sparc B100 sitting in a B1600
chassis.
Any help would be appreciated....
b1600-01bootmode bootscript="boot net" s0
b1600-01reset s0
Are you sure you want to reset S0 (y/n)? y
Reset of S0 successful
b1600-01console s0
[Connected with input enabled on fru S0]
Escape Sequence is '#.'
Probing Memory Bank #0 512 Megabytes
Probing Memory Bank #1 512 Megabytes
Probing Memory Bank #2 0 Megabytes
Probing Memory Bank #3 0 Megabytes
No clientid supplied by the BSC.
Sun Serverblade1 (UltraSPARC-IIe 650MHz), No Keyboard
Copyright 1998-2002 Sun Microsystems, Inc. All rights reserved.
OpenBoot 4.7.5, 1024 MB memory installed, Serial #52823543.
Ethernet address 0:3:ba:2a:11:b8, Host ID: 832605f7.
Boot device: /pci@1f,0/network@a File and args:
1000 Mbps FDXLink up
36800
Server IP address: 10.0.0.10
Client IP address: 10.0.0.20
Consoles: Open Firmware console
Booting with sun4u support.
FreeBSD/sparc64 bootstrap loader, Revision 1.0
(root@obrian.cse.buffalo.edu, Sun Feb 24 17:36:50 UTC 2008)
bootpath="/pci@1f,0/network@a"
boot: ethernet address: 00:03:ba:2a:11:b8
1000 Mbps FDXLink up
net_open: server addr: 10.0.0.10
net_open: server path: /tftpboot
Loading /boot/defaults/loader.conf
/boot/kernel/kernel data=0x6f0848+0x72c68 syms=[0x8+0x76920+0x8+0x6668e]
\
Hit [Enter] to boot immediately, or any other key for command prompt.
Booting [/boot/kernel/kernel] in 9 seconds...
Type '?' for a list of commands, 'help' for more detailed help.
OK set console
Available consoles:
ofw
operation not permitted
OK help set console
/
set console[=<value>]
Sets the current console. If <value> is omitted, a list of
valid
- consoles will be displayed.
OK set console=ofw
OK boot
nothing to autoload yet.
jumping to kernel entry at 0xc0070000.
Copyright (c) 1992-2008 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights
reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 7.0-RELEASE #0: Mon Feb 25 09:35:41 UTC 2008
root@obrian.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC
Timecounter "tick" frequency 650000000 Hz quality 1000
real memory = 1073741824 (1024 MB)
avail memory = 1027727360 (980 MB)
cpu0: Sun Microsystems UltraSparc-IIe Processor (650.00 MHz CPU)
registered firmware set <isp_1000>
registered firmware set <isp_1040>
registered firmware set <isp_1040_it>
registered firmware set <isp_1080>
registered firmware set <isp_1080_it>
registered firmware set <isp_12160>
registered firmware set <isp_12160_it>
registered firmware set <isp_2100>
registered firmware set <isp_2200>
registered firmware set <isp_2300>
registered firmware set <isp_2322>
registered firmware set <isp_2400>
ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413,
RF5413, REGOPS_FUNC)
nexus0: <Open Firmware Nexus device>
pcib0: <U2P UPA-PCI bridge> mem
0x1fe00000000-0x1fe0000ffff,0x1fe01000000-0x1fe010000ff irq
2032,2030,2031,2021 on nexus0
pcib0: Hummingbird compatible, impl 0, version 0, IGN 0x1f, bus A
pcib0: [FILTER]
pcib0: [FILTER]
pcib0: [GIANT-LOCKED]
pcib0: [ITHREAD]
pcib0 dvma: DVMA map: 0xc0000000 to 0xc3ffffff
pcib0: [FILTER]
pci0: <OFW PCI bus> on pcib0
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa_setup_children: no PnP map entry for node 0xf006f7b8: bscbus
isa0: <ISA bus> on isab0
pci0: <old, non-VGA display device> at device 3.0 (no driver attached)
pci0: <network, ethernet> at device 10.0 (no driver attached)
pci0: <network, ethernet> at device 11.0 (no driver attached)
atapci0: <AcerLabs M5229 UDMA100 controller> port
0x900-0x907,0x918-0x91b,0x910-0x917,0x908-0x90b,0x920-0x92f at device
13.0 on pci0
atapci0: [ITHREAD]
atapci0: using PIO transfers above 137GB as workaround for 48bit DMA
access bug, expect reduced performance
ata2: <ATA channel 0> on atapci0
ata2: [ITHREAD]
ata3: <ATA channel 1> on atapci0
ata3: [ITHREAD]
nexus0: <syscons> type unknown (no driver attached)
At this point it just hangs..... any clues ?
Thanks in advance
Craig B
============================================================
This email has been handled by lerwick.hopto.org mail server
and has been scanned by 3 virus killers and spamassassin
============================================================
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?1214865429.1501.6.camel>