Date: Thu, 17 Sep 1998 21:35:49 -0400 (EDT) From: Ted Buswell <tbuswell@mediaone.net> To: freebsd-scsi@FreeBSD.ORG Subject: CAM/ncr messages.. Message-ID: <13825.46672.35984.907842@tbuswell.ne.mediaone.net>
next in thread | raw e-mail | index | archive | help
On a -current system that was CVSup'd and installed today, I'm
getting some interesting messages and was wondering if
anyone had any insight. The messages occur when doing
significant I/O [rm -rf, buildworld, etc.] No softupdates
or anything.
Attached is my dmesg output.
ncr.c is rev 1.128
cam_xpt.c is rev 1.5
Should messages like this be going to -scsi or -current?
Thanks,
-Ted
Copyright (c) 1992-1998 FreeBSD Inc.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
FreeBSD 3.0-CURRENT #0: Thu Sep 17 20:55:48 EDT 1998
tbuswell@tbuswell.ne.mediaone.net:/usr/src/sys/compile/SMPBOX
Timecounter "i8254" frequency 1193182 Hz cost 3372 ns
CPU: Pentium II (686-class CPU)
Origin = "GenuineIntel" Id = 0x634 Stepping=4
Features=0x80fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,MMX>
real memory = 134217728 (131072K bytes)
avail memory = 127528960 (124540K bytes)
Programming 24 pins in IOAPIC #0
FreeBSD/SMP: Multiprocessor motherboard
cpu0 (BSP): apic id: 1, version: 0x00040011, at 0xfee00000
cpu1 (AP): apic id: 0, version: 0x00040011, at 0xfee00000
io0 (APIC): apic id: 2, version: 0x00170011, at 0xfec00000
Probing for devices on PCI bus 0:
chip0: <Host to PCI bridge (vendor=8086 device=7180)> rev 0x03 on pci0.0.0
chip1: <PCI to PCI bridge (vendor=8086 device=7181)> rev 0x03 on pci0.1.0
chip2: <Intel 82371AB PCI to ISA bridge> rev 0x01 on pci0.4.0
chip3: <Intel 82371AB USB host controller> rev 0x01 int d irq 11 on pci0.4.2
chip4: <Intel 82371AB Power management controller> rev 0x01 on pci0.4.3
ahc0: <Adaptec aic7880 Ultra SCSI adapter> rev 0x00 int a irq 19 on pci0.6.0
ahc0: Illegal cable configuration!!. Only two connectors on the adapter may be used at a time!
ahc0: aic7880 Wide Channel A, SCSI Id=7, 16/255 SCBs
de0: <Digital 21041 Ethernet> rev 0x11 int a irq 17 on pci0.11.0
de0: DEC DE450-TA 21041 [10Mb/s] pass 1.1
de0: address 00:00:f8:05:94:b1
ncr0: <ncr 53c825 fast10 wide scsi> rev 0x02 int a irq 16 on pci0.12.0
Probing for devices on PCI bus 1:
vga0: <S3 model 8a10 graphics accelerator> rev 0x04 int a irq 16 on pci1.0.0
Probing for devices on the ISA bus:
sc0 at 0x60-0x6f irq 1 on motherboard
sc0: VGA color <16 virtual consoles, flags=0x0>
ed0 not found at 0x320
ed1 at 0x300-0x31f irq 9 on isa
ed1: address 00:c0:d1:57:4b:24, type NE2000 (16 bit)
sio0 at 0x3f8-0x3ff irq 4 flags 0x10 on isa
sio0: type 16550A
sio1 at 0x2f8-0x2ff irq 3 on isa
sio1: type 16550A
lpt0 at 0x378-0x37f irq 7 on isa
lpt0: Interrupt-driven port
lp0: TCP/IP capable interface
psm0 at 0x60-0x64 irq 12 on motherboard
psm0: model IntelliMouse, device ID 3
fdc0 at 0x3f0-0x3f7 irq 6 drq 2 on isa
fdc0: FIFO enabled, 8 bytes threshold
fd0: 1.44MB 3.5in
npx0 on motherboard
npx0: INT 16 interface
sb0 at 0x220 irq 5 drq 1 on isa
Hmm... Could this be an ESS688 based card (rev 11)
NOTE! SB Pro support required with your soundcard!
snd0: <SoundBlaster Pro 3.1>
opl0 at 0x388 on isa
snd0: <Yamaha OPL3 FM>
sbmidi0 not found at 0x330
de0: enabling 10baseT port
APIC_IO: Testing 8254 interrupt delivery
APIC_IO: routing 8254 via pin 2
IP packet filtering initialized, divert enabled, rule-based forwarding disabled, unlimited logging
SMP: AP CPU #1 Launched!
da0 at ahc0 bus 0 target 5 lun 0
da0: <IOMEGA ZIP 100 J.02> Removable Direct Access SCSI2 device
da0: 3.300MB/s transfers
da0: 96MB (196608 512 byte sectors: 64H 32S/T 96C)
da1 at ncr0 bus 0 target 0 lun 0
da1: <QUANTUM XP34550WD LXY4> Fixed Direct Access SCSI2 device
da1: 20.0MB/s transfers (10.0MHz, offset 8, 16bit), Tagged Queueing Enabled
da1: 4341MB (8890760 512 byte sectors: 255H 63S/T 553C)
da2 at ncr0 bus 0 target 1 lun 0
da2: <QUANTUM XP34550WD LXY4> Fixed Direct Access SCSI2 device
da2: 20.0MB/s transfers (10.0MHz, offset 8, 16bit), Tagged Queueing Enabled
da2: 4341MB (8890760 512 byte sectors: 255H 63S/T 553C)
da3 at ncr0 bus 0 target 2 lun 0
da3: <QUANTUM XP34550WD LXY4> Fixed Direct Access SCSI2 device
da3: 20.0MB/s transfers (10.0MHz, offset 8, 16bit), Tagged Queueing Enabled
da3: 4341MB (8890760 512 byte sectors: 255H 63S/T 553C)
da4 at ncr0 bus 0 target 3 lun 0
da4: <QUANTUM XP34550WD LXY4> Fixed Direct Access SCSI2 device
da4: 20.0MB/s transfers (10.0MHz, offset 8, 16bit), Tagged Queueing Enabled
da4: 4341MB (8890760 512 byte sectors: 255H 63S/T 553C)
cd0 at ahc0 bus 0 target 0 lun 0
cd0: < CRW620 2.03> Removable CD-ROM SCSI2 device
cd0: 3.300MB/s transfers
cd0: Attempt to query device size failed: NOT READY, Medium not present
changing root device to da2s1a
(da4:ncr0:0:3:0): tagged openings now 31
(da2:ncr0:0:1:0): tagged openings now 30
(da4:ncr0:0:3:0): tagged openings now 29
ncr0: timeout nccb=f09dda00 (skip)
ncr0: timeout nccb=f0996400 (skip)
ncr0: timeout nccb=f098aa00 (skip)
ncr0: timeout nccb=f0989600 (skip)
ncr0: timeout nccb=f0989a00 (skip)
ncr0: timeout nccb=f0989c00 (skip)
ncr0: timeout nccb=f0989e00 (skip)
ncr0: timeout nccb=f096de00 (skip)
ncr0: timeout nccb=f096c000 (skip)
(da2:ncr0:0:1:0): tagged openings now 27
ncr0: timeout nccb=f0a7e000 (skip)
ncr0: timeout nccb=f09dde00 (skip)
ncr0: timeout nccb=f09b2800 (skip)
ncr0: timeout nccb=f09b2a00 (skip)
ncr0: timeout nccb=f09b2c00 (skip)
ncr0: timeout nccb=f09b2e00 (skip)
(da2:ncr0:0:1:0): tagged openings now 23
ncr0: timeout nccb=f0989800 (skip)
ncr0: timeout nccb=f0989a00 (skip)
ncr0: timeout nccb=f0989c00 (skip)
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-scsi" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?13825.46672.35984.907842>