Date: Thu, 11 Apr 1996 21:36:56 GMT From: Gary DeMarco <gary@ase.ase.com> To: questions@FreeBSD.ORG Message-ID: <199604112136.VAA01556@localhost>
next in thread | raw e-mail | index | archive | help
Well, here I am again, folks. Had to reinstall the entire system because of problems I was having. Went back to redoing my compiler, and followed the instructions: first, make depend. During this phase got the following error message twice: cc: Internal compiler error: program cpp got fatal signal 11 However, the make depend phase continued without aborting. After this was done, I went ahead with the `make' phase. It continued for a while but then the following occurred: cc -c -O -W -Wreturn-type -Wcomment -Wredundant-decls -I. -I../.. -I../../sys -DGARYP -DI486_CPU -DNCONS=4 -DSCSI_DELAY=5 -DFAT_CURSOR -DUCONSOLE -DCOMPAT_43 -DPROCFS -DCD9660 -DFFS -DINET -DKERNEL -Di386 -DLOAD_ADDRESS=0xF0100000 ../../kern/kern_sig.c cc: Internal compiler error: program cc1 got fatal signal 11 *** Error code 1 Stop. Usually, at this point, I might type `make' again and it would continue on from this point. In this case, though, it kept spitting this same error out at this same point and aborted every time. The following is a copy of my customized kernel file: # # GENERIC -- Generic machine with WD/AHx/NCR/BTx family disks # # GENERIC,v 1.20 1994/11/18 19:10:25 jkh Exp # machine "i386" #cpu "I386_CPU" cpu "I486_CPU" #cpu "I586_CPU" ident GARYP maxusers 10 #options MATH_EMULATE #Support for x87 emulation options INET #InterNETworking options FFS #Berkeley Fast Filesystem #options NFS #Network Filesystem #options MSDOSFS #MSDOS Filesystem options "CD9660" #ISO 9660 Filesystem options PROCFS #Process filesystem options "COMPAT_43" #Compatible with BSD 4.3 options UCONSOLE #X Console support options "FAT_CURSOR" #block cursor in syscons or pccons options "SCSI_DELAY=5" #Be pessimistic about Joe SCSI device options "NCONS=4" #4 virtual consoles #options BOUNCE_BUFFERS #include support for DMA bounce buffers config kernel root on wd0 swap on wd0 and wd1 dumps on wd0 controller isa0 #controller pci0 controller fdc0 at isa? port "IO_FD1" bio irq 6 drq 2 vector fdintr disk fd0 at fdc0 drive 0 disk fd1 at fdc0 drive 1 #tape ft0 at fdc0 drive 2 controller wdc0 at isa? port "IO_WD1" bio irq 14 vector wdintr disk wd0 at wdc0 drive 0 #disk wd1 at wdc0 drive 1 controller wdc1 at isa? port "IO_WD2" bio irq 15 vector wdintr disk wd2 at wdc1 drive 0 #disk wd3 at wdc1 drive 1 controller ncr0 #controller bt0 at isa? port "IO_BT0" bio irq ? vector btintr #controller uha0 at isa? port "IO_UHA0" bio irq ? drq 5 vector uhaintr #controller ahc0 at isa? bio irq ? vector ahcintr #controller ahb0 at isa? bio irq ? vector ahbintr controller aha0 at isa? port "IO_AHA0" bio irq ? drq 5 vector ahaintr #controller aic0 at isa? port 0x340 bio irq 11 vector aicintr #controller pas0 at isa? port 0x1f88 bio #controller sea0 at isa? bio irq 5 iomem 0xc8000 iosiz 0x2000 vector seaintr controller scbus0 device sd0 #device sd1 #device sd2 #device sd3 #device st0 #device st1 device cd0 #Only need one of these, the code dynamically grows #device wt0 at isa? port 0x300 bio irq 5 drq 1 vector wtintr #device mcd0 at isa? port 0x300 bio irq 10 vector mcdintr #device mcd1 at isa? port 0x340 bio irq 11 vector mcdintr device sc0 at isa? port "IO_KBD" tty irq 1 vector scintr device npx0 at isa? port "IO_NPX" irq 13 vector npxintr device sio0 at isa? port "IO_COM1" tty irq 4 vector siointr device sio1 at isa? port "IO_COM2" tty irq 3 vector siointr device sio2 at isa? port "IO_COM3" tty irq 5 vector siointr device sio3 at isa? port "IO_COM4" tty irq 9 vector siointr device lpt0 at isa? port? tty irq 7 vector lptintr #device lpt1 at isa? port? tty #device lpt2 at isa? port? tty #device de0 #device ed0 at isa? port 0x280 net irq 5 iomem 0xd8000 vector edintr #device ed1 at isa? port 0x300 net irq 5 iomem 0xd8000 vector edintr #device ie0 at isa? port 0x360 net irq 7 iomem 0xd0000 vector ieintr #device ep0 at isa? port 0x300 net irq 10 vector epintr #device is0 at isa? port 0x280 net irq 10 drq 7 vector isintr #device le0 at isa? port 0x300 net irq 5 iomem 0xd0000 vector le_intr #device ze0 at isa? port 0x300 net irq 5 iomem 0xd8000 vector zeintr pseudo-device loop #pseudo-device ether pseudo-device log pseudo-device sl 2 pseudo-device pty 16 pseudo-device speaker #pseudo-device gzip # Exec gzipped a.out's If you guys have any suggestion, comments, whatever, please let me know. Appreciate all the help. Gary DeMarco gary@garyp.ase.com
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?199604112136.VAA01556>