Date: Sun, 8 Apr 2001 22:51:17 -0400 From: Matthew Beauchesne <mjb@adam.cheshire.net> To: freebsd-questions@FreeBSD.org Subject: Re: Ensoniq AudioPCI problems. Message-ID: <20010408225117.A225@cheshire.net> In-Reply-To: <Pine.BSF.4.21.0104082126280.4827-100000@shell-3.enteract.com>; from dscheidt@tumbolia.com on Sun, Apr 08, 2001 at 09:28:53PM -0500 References: <20010408221031.B228@cheshire.net> <Pine.BSF.4.21.0104082126280.4827-100000@shell-3.enteract.com>
next in thread | previous in thread | raw e-mail | index | archive | help
--TB36FDmn/VVEgNH/
Content-Type: text/plain; charset=us-ascii
Content-Disposition: inline
On Sun, Apr 08, 2001 at 09:28:53PM -0500, David Scheidt wrote:
> On Sun, 8 Apr 2001, Matthew Beauchesne wrote:
>
> :On Sun, Apr 08, 2001 at 06:52:38PM -0700, Kent Stewart wrote:
> :> You said compiled the kernel but since you are having problems, did you do a
> :> make install and reboot.
> :>
> :> Kent
> :>
> :> >
> :>
> :
> :Yes I did install it and reboot but it still doesn't detect the
> :card.
> :
>
> I don't think this card is supported. The handbook mentions the ENSONIQ
> AudioPCI ES1370/1371 but not the one you've got. Can you post the dmesg
> from a boot -v?
>
> David
Hello,
The card does use the 1371 chip. I had similar problems with the card
under BeOS. It turned out that a certain chip used on the card wasn't
supported. So that just may be the case here. Were there significant
changes in the es1371 driver between 4.0 and 4.2? Would upgrading help?
The output from boot -v should be attached.
--
Matthew Beauchesne
mjb@cheshire.net
--
--TB36FDmn/VVEgNH/
Content-Type: text/plain; charset=us-ascii
Content-Description: boot -v output
Content-Disposition: attachment; filename=log
Copyright (c) 1992-2000 The FreeBSD Project.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
FreeBSD 4.0-RELEASE #8: Sun Apr 8 22:37:39 EDT 2001
root@cheshire.net:/usr/src/sys/compile/MJB
Calibrating clock(s) ... TSC clock: 851887278 Hz, i8254 clock: 1193120 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz
CLK_USE_TSC_CALIBRATION not specified - using old calibration method
CPU: Pentium III/Pentium III Xeon (851.94-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x683 Stepping = 3
Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,XMM>
real memory = 134217728 (131072K bytes)
Physical memory chunk(s):
0x00001000 - 0x0009efff, 647168 bytes (158 pages)
0x0035c000 - 0x07ff7fff, 130662400 bytes (31900 pages)
avail memory = 126763008 (123792K bytes)
bios32: Found BIOS32 Service Directory header at 0xc00faba0
bios32: Entry = 0xfb020 (c00fb020) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xb050
pnpbios: Found PnP BIOS data at 0xc00fbcc0
pnpbios: Entry = f0000:bce8 Rev = 1.0
Other BIOS signatures found:
ACPI: 00000000
Preloaded elf kernel "kernel" at 0xc0343000.
Preloaded userconfig_script "/boot/kernel.conf" at 0xc03430a8.
Pentium Pro MTRR support enabled
md0: Malloc disk
Creating DISK md0
Math emulator present
pci_open(1): mode 1 addr port (0x0cf8) is 0x80000060
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=06911106)
devclass_alloc_unit: pcib0 already exists, using next available unit number
npx0: <math processor> on motherboard
npx0: INT 16 interface
pci_open(1): mode 1 addr port (0x0cf8) is 0x00000000
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=06911106)
pcib0: <Host to PCI bridge> on motherboard
found-> vendor=0x1106, dev=0x0691, revid=0x44
class=06-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[10]: type 1, range 32, base d0000000, size 26
found-> vendor=0x1106, dev=0x8598, revid=0x00
class=06-04-00, hdrtype=0x01, mfdev=0
subordinatebus=1 secondarybus=1
found-> vendor=0x1106, dev=0x0686, revid=0x1b
class=06-01-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
found-> vendor=0x1106, dev=0x0571, revid=0x06
class=01-01-8a, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[20]: type 1, range 32, base 0000c000, size 4
found-> vendor=0x1106, dev=0x3038, revid=0x0e
class=0c-03-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=d, irq=11
map[20]: type 1, range 32, base 0000c400, size 5
found-> vendor=0x1106, dev=0x3038, revid=0x0e
class=0c-03-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=d, irq=11
map[20]: type 1, range 32, base 0000c800, size 5
found-> vendor=0x1106, dev=0x3057, revid=0x20
class=06-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
found-> vendor=0x1106, dev=0x3058, revid=0x21
class=04-01-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=c, irq=10
map[10]: type 1, range 32, base 0000cc00, size 8
map[14]: type 1, range 32, base 0000d000, size 2
map[18]: type 1, range 32, base 0000d400, size 2
found-> vendor=0x9004, dev=0x5078, revid=0x03
class=01-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=5
map[10]: type 1, range 32, base 0000d800, size 8
map[14]: type 1, range 32, base d9000000, size 12
found-> vendor=0x121a, dev=0x0005, revid=0x01
class=03-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=9
map[10]: type 1, range 32, base d4000000, size 25
map[14]: type 1, range 32, base d6000000, size 25
map[18]: type 1, range 32, base 0000dc00, size 8
found-> vendor=0x1274, dev=0x5880, revid=0x02
class=04-01-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=10
map[10]: type 1, range 32, base 0000e000, size 6
found-> vendor=0x109e, dev=0x036e, revid=0x02
class=04-00-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
intpin=a, irq=11
map[10]: type 1, range 32, base d9001000, size 12
found-> vendor=0x109e, dev=0x0878, revid=0x02
class=04-80-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
intpin=a, irq=11
map[10]: type 1, range 32, base d9002000, size 12
pci0: <PCI bus> on pcib0
pcib2: <VIA 82C598MVP (Apollo MVP3) PCI-PCI (AGP) bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib2
isab0: <VIA 82C686 PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <VIA 82C686 ATA66 controller> port 0xc000-0xc00f at device 7.1 on pci0
ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0xc000
ata0: mask=03 status0=50 status1=50
ata0: mask=03 status0=50 status1=50
ata0: devices = 0x3
ata0: at 0x1f0 irq 14 on atapci0
ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0xc008
ata1: mask=03 status0=7f status1=7f
ata1: mask=03 status0=7d status1=7f
ata1: devices = 0x0
ata1: probe allocation failed
pci0: <VIA 83C572 USB controller> (vendor=0x1106, dev=0x3038) at 7.2 irq 11
pci0: <VIA 83C572 USB controller> (vendor=0x1106, dev=0x3038) at 7.3 irq 11
chip2: <VIA 82C686 AC97 Audio> port 0xd400-0xd403,0xd000-0xd003,0xcc00-0xccff irq 10 at device 7.5 on pci0
ahc0: <Adaptec 2910/15/20/30C SCSI adapter> port 0xd800-0xd8ff mem 0xd9000000-0xd9000fff irq 5 at device 15.0 on pci0
ahc0: No SEEPROM available.
ahc0: aic7850 Single Channel A, SCSI Id=7, 3/255 SCBs
ahc0: Host Adapter Bios disabled. Using default SCSI device parameters
ahc0: Downloading Sequencer Program... 411 instructions downloaded
pci0: <3Dfx Voodoo 3 graphics accelerator> (vendor=0x121a, dev=0x0005) at 16.0 irq 9
pci0: <unknown card> (vendor=0x1274, dev=0x5880) at 19.0 irq 10
pci0: <unknown card> (vendor=0x109e, dev=0x036e) at 20.0 irq 11
pci0: <unknown card> (vendor=0x109e, dev=0x0878) at 20.1 irq 11
pci_open(1): mode 1 addr port (0x0cf8) is 0x00000000
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=06911106)
devclass_alloc_unit: pci1 already exists, using next available unit number
pcib1: <Host to PCI bridge> on motherboard
pci2: <PCI bus> on pcib1
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
devclass_alloc_unit: ata0 already exists, using next available unit number
devclass_alloc_unit: ata1 already exists, using next available unit number
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ata3: iobase=0x0170 altiobase=0x0376 bmaddr=0x0000
ata3: mask=03 status0=48 status1=7f
ata3: mask=03 status0=7f status1=78
ata3: devices = 0x0
ata3: probe allocation failed
atkbdc0: <keyboard controller (i8042)> at port 0x60-0x6f on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0047
atkbd: keyboard ID 0x41ab (2)
kbdc: RESET_KBD return code:00fa
kbdc: RESET_KBD status:00aa
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
psm0: current command byte:0047
kbdc: TEST_AUX_PORT status:0000
kbdc: RESET_AUX return code:00fa
kbdc: RESET_AUX status:00aa
kbdc: RESET_AUX ID:0000
psm: status 00 02 64
psm: status 90 03 3c
psm: status 90 03 3c
psm: status 90 03 3c
psm: status 00 00 0a
psm: data 08 00 00
psm: status 00 02 64
psm: data 08 00 00
psm: status 00 02 64
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0-00, 3 buttons
psm0: config:00000000, flags:00000000, packet size:3
psm0: syncmask:c0, syncbits:00
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0e 0f 00 00 07 80 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
sc0: <System console> on isa0
sc0: VGA <16 virtual consoles, flags=0x200>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio0: irq maps: 0x2001 0x2011 0x2001 0x2001
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: irq maps: 0x2001 0x2009 0x2001 0x2001
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
sio2: not probed (disabled)
sio3: not probed (disabled)
ppc0: parallel port found at 0x378
ppc0: EPP SPP
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
ppi0: <Parallel I/O> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
plip0: <PLIP network interface> on ppbus0
bpf: lp0 attached
isa_probe_children: probing PnP devices
BIOS Geometries:
0:03fffe3f 0..1023=1024 cylinders, 0..254=255 heads, 1..63=63 sectors
1:020bfe3f 0..523=524 cylinders, 0..254=255 heads, 1..63=63 sectors
0 accounted for
Device configuration finished.
bpf: sl0 attached
bpf: ppp0 attached
new masks: bio 40084040, tty 4003109a, net 4007109a
bpf: lo0 attached
bpf: gif0 attached
bpf: gif1 attached
bpf: gif2 attached
bpf: gif3 attached
bpf: stf0 attached
bpf: faith0 attached
ata0-master: success setting up UDMA4 mode on VIA chip
ad0: <ST313021A/3.03> ATA-5 disk at ata0 as master
ad0: 12419MB (25434228 sectors), 25232 cyls, 16 heads, 63 S/T, 512 B/S
ad0: 16 secs/int, 1 depth queue, UDMA66
ad0: piomode=4 dmamode=2 udmamode=4 cblid=1
Creating DISK ad0
Creating DISK wd0
ata0-slave: success setting up UDMA4 mode on VIA chip
ad1: <WDC WD43AA/29.05T29> ATA-4 disk at ata0 as slave
ad1: 4112MB (8421840 sectors), 8355 cyls, 16 heads, 63 S/T, 512 B/S
ad1: 16 secs/int, 1 depth queue, UDMA66
ad1: piomode=4 dmamode=2 udmamode=4 cblid=1
Creating DISK ad1
Creating DISK wd1
Waiting 15 seconds for SCSI devices to settle
(noperiph:ahc0:0:-1:-1): SCSI bus reset delivered. 0 SCBs aborted.
(probe3:ahc0:0:3:0): INQUIRY. CDB: 12 1 80 0 ff 0
(probe3:ahc0:0:3:0): ILLEGAL REQUEST asc:24,0
(probe3:ahc0:0:3:0): Invalid field in CDB
ahc0: target 3 synchronous at 5.0MHz, offset = 0xf
ahc0: target 6 synchronous at 10.0MHz, offset = 0x8
Creating DISK cd0
Creating DISK cd1
pass0 at ahc0 bus 0 target 3 lun 0
pass0: <SONY CD-ROM CDU-76S 1.0a> Removable CD-ROM SCSI-2 device
pass0: 5.681MB/s transfers (5.681MHz, offset 15)
pass1 at ahc0 bus 0 target 6 lun 0
pass1: <SAF CD-R8020 1.24> Removable CD-ROM SCSI-2 device
pass1: Serial Number \^_
pass1: 10.000MB/s transfers (10.000MHz, offset 8)
Mounting root from ufs:/dev/ad0s1a
ad0s1: type 0xa5, start 63, end = 25430894, size 25430832 : OK
cd1 at ahc0 bus 0 target 6 lun 0
cd1: <SAF CD-R8020 1.24> Removable CD-ROM SCSI-2 device
cd1: Serial Number \^_
cd1: 10.000MB/s transfers (10.000MHz, offset 8)
cd1: cd present [320584 x 2048 byte records]
cd0 at ahc0 bus 0 target 3 lun 0
cd0: <SONY CD-ROM CDU-76S 1.0a> Removable CD-ROM SCSI-2 device
cd0: 5.681MB/s transfers (5.681MHz, offset 15)
cd0: cd present [260752 x 2048 byte records]
start_init: trying /sbin/init
Linux-ELF exec handler installed
splash: image decoder found: logo_saver
--TB36FDmn/VVEgNH/--
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20010408225117.A225>