Date: Tue, 23 Apr 2002 00:44:26 -0400 From: parv <parv@subdimension.com> To: sonam singh <sonamsinghl@yahoo.com> Cc: mobile@freebsd.org Subject: Re: Please Help ..Modem & Sound Info Message-ID: <20020423044426.GA7353@moo.holy.cow> In-Reply-To: <20020423042427.94630.qmail@web14402.mail.yahoo.com> References: <20020423042427.94630.qmail@web14402.mail.yahoo.com>
next in thread | previous in thread | raw e-mail | index | archive | help
in message <20020423042427.94630.qmail@web14402.mail.yahoo.com>, wrote sonam singh thusly... > > I successfuly installed the FreeBSD4.5 on ... Dell Inspiron 4100 > Laptop .but i am not able to configure the modem and sound card > .It has PCtel Modem & Crystal 4205 Sound card . it would help if you tell us the what are the actual problems and/or error messages w/ the modem or the sound card. what/how were you trying to configure that gave you grief? i don't have any experience w/ the mentioned sound card. modem, however, from the dmesg looks like, should just work ... unless it's a software modem. speaking of which, what do you have for "sio" in your kernel. for example, i have... # Serial (COM) ports # sio0/com1 -- 9-pin serial port on dell inspiron 5000e # sio2/com3 is winmodem device sio0 at isa? port IO_COM1 flags 0x10 irq 4 #device sio1 at isa? port IO_COM2 irq 3 device sio2 at isa? disable port IO_COM3 ...and, if possible, please do not wrap the computer generated messages like dmesg output below. - parv > here is output of dmesg. i also try same thing which u > mentioned . I recompile the kernle with > device pcm > device csa ... > Copyright (c) 1992-2002 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, > 1991, 1992, 1993, 1994 > The Regents of the University of California. All > rights reserved. > FreeBSD 4.5-RELEASE #0: Sun Apr 7 10:49:54 IST 2002 > > root@sonamsingh.com:/usr/src/sys/compile/SON_KER2_1 > Timecounter "i8254" frequency 1193182 Hz > CPU: Pentium III/Pentium III Xeon/Celeron (863.79-MHz > 686-class CPU) > Origin = "GenuineIntel" Id = 0x6b1 Stepping = 1 > > Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE> > real memory = 134094848 (130952K bytes) > config> di sn0 > config> di lnc0 > config> di le0 > No such device: le0 > Invalid command or syntax. Type `?' for help. > config> di ie0 > config> di fe0 > config> di ed0 > config> di cs0 > config> q > avail memory = 125517824 (122576K bytes) > Preloaded elf kernel "kernel" at 0xc04e1000. > Preloaded userconfig_script "/boot/kernel.conf" at > 0xc04e109c. > Pentium Pro MTRR support enabled > md0: Malloc disk > Using $PIR table, 11 entries at 0xc00fbba0 > apm0: <APM BIOS> on motherboard > apm: found APM BIOS v1.2, connected at v1.2 > npx0: <math processor> on motherboard > npx0: INT 16 interface > pcib0: <Host to PCI bridge> on motherboard > pci0: <PCI bus> on pcib0 > pcib1: <PCI to PCI bridge (vendor=8086 device=3576)> > at device 1.0 on pci0 > pci1: <PCI bus> on pcib1 > pci1: <ATI model 4c59 graphics accelerator> at 0.0 irq > 11 > uhci0: <UHCI (generic) USB controller> port > 0xbf80-0xbf9f irq 11 at device 29.0 on pci0 > uhci0: (New UHCI DeviceId=0x24828086) > usb0: <UHCI (generic) USB controller> on uhci0 > usb0: USB revision 1.0 > uhub0: (0x24828086) UHCI root hub, class 9/0, rev > 1.00/1.00, addr 1 > uhub0: 2 ports with 2 removable, self powered > pcib2: <PCI to PCI bridge (vendor=8086 device=2448)> > at device 30.0 on pci0 > pci2: <PCI bus> on pcib2 > pcic0: <TI PCI-1420 PCI-CardBus Bridge> irq 11 at > device 1.0 on pci2 > pcic0: PCI Memory allocated: 0x44000000 > pcic0: TI12XX PCI Config Reg: [ring enable][speaker > enable][CSC serial isa irq] > pccard0: <PC Card bus (classic)> on pcic0 > pcic1: <TI PCI-1420 PCI-CardBus Bridge> irq 11 at > device 1.1 on pci2 > pcic1: PCI Memory allocated: 0x44001000 > pcic1: TI12XX PCI Config Reg: [ring enable][speaker > enable][CSC serial isa irq] > pccard1: <PC Card bus (classic)> on pcic1 > isab0: <PCI to ISA bridge (vendor=8086 device=248c)> > at device 31.0 on pci0 > isa0: <ISA bus> on isab0 > atapci0: <Intel ICH3 ATA100 controller> port > 0xbfa0-0xbfaf,0x374-0x377,0x170-0x177,0x3f4-0x3f7,0x1f0-0x1f7 > irq 0 at device 31.1 on pci0 > ata0: at 0x1f0 irq 14 on atapci0 > ata1: at 0x170 irq 15 on atapci0 > pcm0: <Intel 82801CA (ICH3)> port > 0xdc80-0xdcbf,0xd800-0xd8ff irq 11 at device 31.5 on > pci0 > pci0: <unknown card> (vendor=0x8086, dev=0x2486) at > 31.6 irq 11 > orm0: <Option ROMs> at iomem > 0xc0000-0xcefff,0xcf000-0xcf7ff,0xcf800-0xcffff on > isa0 > fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 > irq 6 drq 2 on isa0 > fdc0: FIFO enabled, 8 bytes threshold > fd0: <1440-KB 3.5" drive> on fdc0 drive 0 > atkbdc0: <Keyboard controller (i8042)> at port > 0x60,0x64 on isa0 > atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 > kbd0 at atkbd0 > psm0: <PS/2 Mouse> irq 12 on atkbdc0 > psm0: model Generic PS/2 mouse, device ID 0 > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem > 0xa0000-0xbffff on isa0 > sc0: <System console> at flags 0x100 on isa0 > sc0: VGA <16 virtual consoles, flags=0x300> > sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 > sio0: type 16550A > sio1: configured irq 3 not in bitmap of probed irqs 0 > ppc0: <Parallel port> at port 0x378-0x37f irq 7 on > isa0 > ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in > COMPATIBLE mode > ppc0: FIFO with 16/16/8 bytes threshold > plip0: <PLIP network interface> on ppbus0 > lpt0: <Printer> on ppbus0 > lpt0: Interrupt-driven port > ppi0: <Parallel I/O> on ppbus0 > pccard: card inserted, slot 0 > pccard: card removed, slot 0 > pcic0: Card type 32-bit cardbus is unsupported > ad0: 19077MB <IC25N020ATDA04-0> [38760/16/63] at > ata0-master UDMA100 > acd0: CDROM <LG CD-ROM CRN-8245B> at ata1-master using > PIO4 > Mounting root from ufs:/dev/ad0s2a -- To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-mobile" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20020423044426.GA7353>