Date: Fri, 26 Apr 2002 10:42:12 -0700 From: Aditya <aditya@mighty.grot.org> To: freebsd-sparc@freebsd.org Subject: Netra X1 hme ethernet interfaces? [was Re: Netra X1 ISO boot success] Message-ID: <20020426174212.GA25727@mighty.grot.org> In-Reply-To: <20020426063346.GA3931@mighty.grot.org> References: <20020426063346.GA3931@mighty.grot.org>
next in thread | previous in thread | raw e-mail | index | archive | help
I got my Netra X1 to successfully boot off of the IDE drive by following the advice at: http://docs.freebsd.org/cgi/getmsg.cgi?fetch=12853+0+archive/2002/freebsd-sparc/20020421.freebsd-sparc to dd if=/dev/zero of=/dev/ad0 count=16 *before* disklabeling. That seems to have made all the difference. In any case, the box boots fine, however I can't try to cvsup as the on-board, dual ethernet ports (hme) don't seem to be recognized. dmesg output below: ok boot /pci@1f,0/ide@d/disk@0,0 Res LOM event: +12h32m36s host reset etting ... Processor Speed = 400 MHz Baud rate is 9600 8 Data bits, 1 stop bits, no parity (configured from lom) Firmware CORE Sun Microsystems, Inc. @(#) core 1.0.1 2001/02/19 09:55 Software Power ON Verifying NVRAM...Done Bootmode is 0 MCR0 = 16a0b004 MCR1 = c0804000 MCR2 = fe0abb0 MCR3 = 39b Ecache Size = 256 KB Clearing E$ Tags Done Clearing I/D TLBs Done Probing memory Done MEMBASE=0x60000000 MEMSIZE=0x8000000 Clearing memory...Done Turing ON MMUs Done Copy ROM to RAM (148440 bytes) Done Orig PC=0x1fff0007efc New PC=0xf0f07f54 Processor Speed=400MHz Looking for Dropin FVM ... found Decompressing Client Done Transferring control to Client... Reset Control: BXIR:0 BPOR:0 SXIR:0 SPOR:1 POR:0 Probing upa at 1f,0 pci Probing upa at 0,0 SUNW,UltraSPARC-IIe (256 Kb) Loading Support Packages: kbd-translator Loading onboard drivers: Probing /pci@1f,0 Device 7 isa dma rtc power SUNW,lomh serial serial flashprom Probing /pci@1f,0 Device 3 pmu i2c temperature dimm dimm dimm i2c-nvram idprom motherboard-fru ppm beep fan-control lomp Probing Memory Bank #0 0 Megabytes Probing Memory Bank #1 256 Megabytes Probing Memory Bank #2 256 Megabytes Probing Memory Bank #3 128 Megabytes Probing /pci@1f,0 Device 7 Probing /pci@1f,0 Device 3 Probing /pci@1f,0 Device c ethernet Probing /pci@1f,0 Device 5 ethernet Probing /pci@1f,0 Device a usb Probing /pci@1f,0 Device d ide disk cdrom Sun Netra X1 (UltraSPARC-IIe 400MHz), No Keyboard OpenBoot 4.0, 640 MB memory installed, Serial #50992570. Ethernet address 0:3:ba:a:15:ba, Host ID: 830a15ba. Environment monitoring: disabled Executing last command: boot /pci@1f,0/ide@d/disk@0,0 Boot device: /pci@1f,0/ide@d/disk@0,0 File and args: >> FreeBSD/sparc64 boot block Boot path: /pci@1f,0/ide@d/disk@0,0:a Boot loader: /boot/loader Console: OpenFirmware console disk0 is /pci@1f,0/ide@d/disk@0 FreeBSD/sparc64 loader bootpath="/pci@1f,0/ide@d/disk@0,0:a" loaddev=disk0s0a: > \ \: unknown command \ /boot/kernel/kernel data=0x2ca608+0xf2f38 syms=[0x8+0x42b28+0x8+0x349ee] Hit [Enter] to boot immediately, or any other key for command prompt. Booting [/boot/kernel/kernel]... nothing to autoload yet. jumping to kernel entry at 0x80038000. Copyright (c) 1992-2002 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 5.0-CURRENT #9: Tue Apr 9 04:25:17 GMT 2002 jake@u60.locore.ca:/usr/current/src/sys/sparc64/compile/GENERIC Preloaded elf kernel "/boot/kernel/kernel" at 0x80438000. Timecounter "tick" frequency 400000000 Hz cpu0: Sun Microsystems UltraSparc-IIe Processor (400.00 MHZ CPU) nexus0: <OpenFirmware Nexus device> pcib0: <U2P UPA-PCI bridge> on nexus0 pcib0: SUNW,sabre: impl 0, version 0: ign 7c0 bus range 0 to 0; PCI bus 0 DVMA map: 0x60000000 to 0x7fffffff pcib0: ofw_pci_init_intr: no interrupt mapping found for 0/7/0 (preset 0) pcib0: ofw_pci_init_intr: no interrupt mapping found for 0/3/0 (preset 0) pcib0: ofw_pci_init_intr: no interrupt mapping found for 0/3/0 (preset 0) pcib0: ofw_pci_init_intr: mapping intr for 0/12/0 to 6 (preset was 0) pcib0: ofw_pci_init_intr: mapping intr for 0/5/0 to 28 (preset was 0) pcib0: ofw_pci_init_intr: mapping intr for 0/10/0 to 36 (preset was 0) pcib0: ofw_pci_init_intr: mapping intr for 0/13/0 to 12 (preset was 0) pci0: <PCI bus> on pcib0 pci0: <old, non-VGA display device> at device 3.0 (no driver attached) pci0: <network, ethernet> at device 5.0 (no driver attached) isab0: <PCI-ISA bridge> at device 7.0 on pci0 isa0: <ISA bus> on isab0 pci0: <serial bus, USB> at device 10.0 (no driver attached) pci0: <network, ethernet> at device 12.0 (no driver attached) atapci0: <AcerLabs Aladdin ATA66 controller> port 0x10220-0x1022f,0x10208-0x1020b,0x10210-0x10217,0x10218-0x1021b,0x10200-0x10207 irq 12 at device 13.0 on pci0 ata2: at 0x10200 on atapci0 ata3: at 0x10210 on atapci0 ad0: 2014MB <FUJITSU MPA3026ATU> [4092/16/63] at ata2-master UDMA33 acd0: CDROM <ATAPI CDROM> at ata3-master PIO4 Manual root filesystem specification: <fstype>:<device> Mount <device> using filesystem <fstype> eg. ufs:da0a ? List valid disk boot devices <empty line> Abort manual input mountroot> ufs:ad0a Mounting root from ufs:ad0a ... # uname -a FreeBSD 5.0-CURRENT FreeBSD 5.0-CURRENT #9: Tue Apr 9 04:25:17 GMT 2002 jake@u60.locore.ca:/usr/current/src/sys/sparc64/compile/GENERIC sparc64 # Thanks, Adi On Thu, Apr 25, 2002 at 11:33:46PM -0700, Aditya wrote: > I've been able to boot the image in sparc64-20020408.iso with a CDROM drive on > a Netra X1 successfully. I was able to follow the install instructions to > disklabel, copy and untar the distribution on the ISO onto the IDE. However, > it seems to "hang" when I try to boot off the newly installed IDE (I did a > disklabel -B on it). The output is given below. I suspect I've missed a step, > but can't figure it out so would welcome any hints. > > ... > Probing /pci@1f,0 Device 7 > Probing /pci@1f,0 Device 3 > Probing /pci@1f,0 Device c ethernet > Probing /pci@1f,0 Device 5 ethernet > Probing /pci@1f,0 Device a usb > Probing /pci@1f,0 Device d ide disk cdrom > Sun Netra X1 (UltraSPARC-IIe 400MHz), No Keyboard > OpenBoot 4.0, 640 MB memory installed, Serial #50992570. > Ethernet address 0:3:ba:a:15:ba, Host ID: 830a15ba. > > > > Environment monitoring: disabled > Executing last command: boot disk0 > Boot device: /pci@1f,0/ide@d/disk@0,0 File and args: > > at this point, it just hangs. > > Thanks, > Adi > > To Unsubscribe: send mail to majordomo@FreeBSD.org > with "unsubscribe freebsd-sparc" in the body of the message To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-sparc" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20020426174212.GA25727>