Date: Fri, 20 Sep 2002 10:50:34 GMT From: "zvezdi" <zvezdi@LanGame.Net> To: hackers@freebsd.org Subject: microuptime() went backwards? Message-ID: <20020920105034.48316.qmail@mailman.langame.net>
next in thread | raw e-mail | index | archive | help
I have dual pentium, and started lately to come to the
console.
microuptime() went backwards.
I went over the list (hackers) and saw the last discussion
on microuptime() which suggested to remove apm0.
I have it disabled in my config (by default), but still I see these.
APM is disabled in the bios.
I had some problems 1 month ago, when this system didn't want
to boot, and always was freesing at USBxx at the boot process,
nomatter that usb?x didn't existed in the config??? and the
usb devices were disabled by the bios.
Any ideas on what should I do?
Thank you very much for your time.
Zvezdelin Vladov
--dmesg-boot-
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.6.2-RELEASE #0: Mon Aug 26 12:00:32 EEST 2002
basic@fix.langame.net:/usr/src/obj/usr/src/sys/FIX-GW
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium III/Pentium III Xeon/Celeron (548.54-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x673 Stepping = 3
Features=0x387fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA
,
CMOV,PAT,PSE36,PN,MMX,FXSR,SSE>
real memory = 536805376 (524224K bytes)
avail memory = 518836224 (506676K bytes)
Programming 24 pins in IOAPIC #0
IOAPIC #0 intpin 2 -> irq 0
FreeBSD/SMP: Multiprocessor motherboard
cpu0 (BSP): apic id: 0, version: 0x00040011, at 0xfee00000
cpu1 (AP): apic id: 1, version: 0x00040011, at 0xfee00000
io0 (APIC): apic id: 2, version: 0x00170011, at 0xfec00000
Preloaded elf kernel "kernel" at 0xc032d000.
Pentium Pro MTRR support enabled
md0: Malloc disk
Using $PIR table, 7 entries at 0xc00fdd10
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82443BX (440 BX) host to PCI bridge> on motherboard
IOAPIC #0 intpin 18 -> irq 2
IOAPIC #0 intpin 19 -> irq 16
pci0: <PCI bus> on pcib0
pcib1: <Intel 82443BX (440 BX) PCI-PCI (AGP) bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
isab0: <Intel 82371AB PCI to ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0xf000-0xf00f at device 7.1 on
pc
i0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pci0: <Intel 82371AB/EB (PIIX4) USB controller> at 7.2
Timecounter "PIIX" frequency 3579545 Hz
chip1: <Intel 82371AB Power management controller> port 0x5000-0x500f at
devic
e 7.3 on pci0
xl0: <3Com 3c905B-TX Fast Etherlink XL> port 0xe400-0xe47f mem
0xe6001000-0xe6
00107f irq 2 at device 10.0 on pci0
xl0: Ethernet address: 00:50:da:51:16:d9
miibus0: <MII bus> on xl0
xlphy0: <3Com internal media interface> on miibus0
xlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
xl1: <3Com 3c905B-TX Fast Etherlink XL> port 0xe800-0xe87f mem
0xe6000000-0xe6
00007f irq 16 at device 11.0 on pci0
xl1: Ethernet address: 00:50:da:51:18:d1
miibus1: <MII bus> on xl1
xlphy1: <3Com internal media interface> on miibus1
xlphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
orm0: <Option ROM> at iomem 0xc0000-0xc7fff on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> on isa0
sc0: VGA <16 virtual consoles, flags=0x200>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
APIC_IO: Testing 8254 interrupt delivery
APIC_IO: routing 8254 via IOAPIC #0 intpin 2
IP packet filtering initialized, divert enabled, rule-based forwarding
enabled
, default to accept, logging limited to 100 packets/entry by default
DUMMYNET initialized (011031)
SMP: AP CPU #1 Launched!
ad0: 8063MB <QUANTUM FIREBALL CR8.4A> [16383/16/63] at ata0-master UDMA33
Mounting root from ufs:/dev/ad0s1a
---------
config:
---------
machine i386
#cpu I386_CPU
#cpu I486_CPU
#cpu I586_CPU
cpu I686_CPU
ident FIX-GW
maxusers 128
#makeoptions DEBUG=-g #Build kernel with gdb(1) debug
symbols
options MAXDSIZ=(1024UL*1024*1024)
options NMBCLUSTERS=65535
options MATH_EMULATE #Support for x87 emulation
options INET #InterNETworking
#options INET6 #IPv6 communications protocols
options FFS #Berkeley Fast Filesystem
options FFS_ROOT #FFS usable as root device [keep
this!
]
options MFS #Memory Filesystem
#options MD_ROOT #MD is a potential root device
#options NFS #Network Filesystem
#options NFS_ROOT #NFS usable as root device, NFS
requir
ed
options MSDOSFS #MSDOS Filesystem
options CD9660 #ISO 9660 Filesystem
options CD9660_ROOT #CD-ROM usable as root, CD9660
require
d
options PROCFS #Process filesystem
options COMPAT_43 #Compatible with BSD 4.3 [KEEP
THIS!]
options SCSI_DELAY=15000 #Delay (in ms) before probing SCSI
options UCONSOLE #Allow users to grab the console
options USERCONFIG #boot -c editor
options VISUAL_USERCONFIG #visual boot -c editor
options KTRACE #ktrace(1) support
options SYSVSHM #SYSV-style shared memory
options SYSVMSG #SYSV-style message queues
options SYSVSEM #SYSV-style semaphores
options P1003_1B #Posix P1003_1B real-time extentions
options _KPOSIX_PRIORITY_SCHEDULING
options ICMP_BANDLIM #Rate limit bad replies
options IPFIREWALL # firewall
options IPFIREWALL_VERBOSE #print information about
# dropped packets
options IPFIREWALL_FORWARD #enable transparent proxy support
options IPFIREWALL_VERBOSE_LIMIT=100 #limit verbosity
options IPFIREWALL_DEFAULT_TO_ACCEPT #allow everything by default
options IPDIVERT
#options IPFILTER #ipfilter support
#options IPFILTER_LOG #ipfilter logging
#options IPSTEALTH #support for stealth forwarding
options DUMMYNET
#options BRIDGE
#options IPX
#options NCP
# To make an SMP kernel, the next two are needed
options SMP # Symmetric MultiProcessor Kernel
options APIC_IO # Symmetric (APIC) I/O
# Optionally these may need tweaked, (defaults shown):
#options NCPU=2 # number of CPUs
#options NBUS=4 # number of busses
#options NAPIC=2 # number of IO APICs
#options NINTR=24 # number of INTs
device isa
#device eisa
device pci
# Floppy drives
device fdc0 at isa? port IO_FD1 irq 6 drq 2
device fd0 at fdc0 drive 0
device fd1 at fdc0 drive 1
# ATA and ATAPI devices
device ata0 at isa? port IO_WD1 irq 14
device ata1 at isa? port IO_WD2 irq 15
device ata
device atadisk # ATA disk drives
device atapicd # ATAPI CDROM drives
device atapifd # ATAPI floppy drives
device atapist # ATAPI tape drives
options ATA_STATIC_ID #Static device numbering
#options ATA_ENABLE_ATAPI_DMA #Enable DMA on ATAPI devices
# SCSI Controllers
#device ahb # EISA AHA1742 family
device ahc # AHA2940 and onboard AIC7xxx devices
#device amd # AMD 53C974 (Teckram DC-390(T))
#device dpt # DPT Smartcache - See LINT for options!
#device isp # Qlogic family
#device ncr # NCR/Symbios Logic
#device sym # NCR/Symbios Logic (newer chipsets)
device adv0 at isa?
device adw
device bt0 at isa?
device aha0 at isa?
device aic0 at isa?
# SCSI peripherals
device scbus # SCSI bus (required)
device da # Direct Access (disks)
device sa # Sequential Access (tape etc)
device cd # CD
device pass # Passthrough device (direct SCSI access)
# RAID controllers
#device ida # Compaq Smart RAID
#device amr # AMI MegaRAID
#device mlx # Mylex DAC960 family
# atkbdc0 controls both the keyboard and the PS/2 mouse
device atkbdc0 at isa? port IO_KBD
device atkbd0 at atkbdc? irq 1
device psm0 at atkbdc? irq 12
device vga0 at isa?
# splash screen/screen saver
pseudo-device splash
# syscons is the default console driver, resembling an SCO console
device sc0 at isa?
# Enable this and PCVT_FREEBSD for pcvt vt220 compatible console driver
#device vt0 at isa?
#options XSERVER # support for X server on a vt
console
options FAT_CURSOR # start with block cursor
# If you have a ThinkPAD, uncomment this along with the rest of the PCVT
lines
#options PCVT_SCANSET=2 # IBM keyboards are non-std
# Floating point support - do not disable.
device npx0 at nexus? port IO_NPX irq 13
# Power management support (see LINT for more options)
#device apm0 at nexus? disable flags 0x20 # Advanced Power
Manageme
nt
# PCCARD (PCMCIA) support
#device card
#device pcic0 at isa? irq 10 port 0x3e0 iomem 0xd0000
#device pcic1 at isa? irq 11 port 0x3e2 iomem 0xd4000 disable
# Serial (COM) ports
device sio0 at isa? port IO_COM1 flags 0x10 irq 4
device sio1 at isa? port IO_COM2 irq 3
device sio2 at isa? disable port IO_COM3 irq 5
device sio3 at isa? disable port IO_COM4 irq 9
# Parallel port
device ppc0 at isa? irq 7
device ppbus # Parallel port bus (required)
device lpt # Printer
device plip # TCP/IP over parallel
device ppi # Parallel port interface device
#device vpo # Requires scbus and da
# PCI Ethernet NICs.
#device de # DEC/Intel DC21x4x (``Tulip'')
#device fxp # Intel EtherExpress PRO/100B (82557, 82558)
#device tx # SMC 9432TX (83c170 ``EPIC'')
device vx # 3Com 3c590, 3c595 (``Vortex'')
#device wx # Intel Gigabit Ethernet Card (``Wiseman'')
# PCI Ethernet NICs that use the common MII bus controller code.
device miibus # MII bus support
#device dc # DEC/Intel 21143 and various workalikes
device rl # RealTek 8129/8139
#device sf # Adaptec AIC-6915 (``Starfire'')
#device sis # Silicon Integrated Systems SiS 900/SiS
7016
#device ste # Sundance ST201 (D-Link DFE-550TX)
#device tl # Texas Instruments ThunderLAN
device vr # VIA Rhine, Rhine II
device wb # Winbond W89C840F
device xl # 3Com 3c90x (``Boomerang'', ``Cyclone'')
# ISA Ethernet NICs.
device ed0 at isa? port 0x280 irq 10 iomem 0xd8000
#device ex
#device ep
# WaveLAN/IEEE 802.11 wireless NICs. Note: the WaveLAN/IEEE really
# exists only as a PCMCIA device, so there is no ISA attatement needed
# and resources will always be dynamically assigned by the pccard code.
#device wi
# Aironet 4500/4800 802.11 wireless NICs. Note: the declaration below will
# work for PCMCIA and PCI cards, as well as ISA cards set to ISA PnP
# mode (the factory default). If you set the switches on your ISA
# card for a manually chosen I/O address and IRQ, you must specify
## those paremeters here.
#device an
# The probe order of these is presently determined by i386/isa/isa_compat.c.
#device ie0 at isa? port 0x300 irq 10 iomem 0xd0000
#device fe0 at isa? port 0x300
#device le0 at isa? port 0x300 irq 5 iomem 0xd0000
#device lnc0 at isa? port 0x280 irq 10 drq 0
#device cs0 at isa? port 0x300
#device sn0 at isa? port 0x300 irq 10
# requires PCCARD (PCMCIA) support to be activated
#device xe0 at isa?
# Pseudo devices - the number indicates how many units to allocated.
pseudo-device loop # Network loopback
pseudo-device ether # Ethernet support
pseudo-device sl 1 # Kernel SLIP
pseudo-device ppp 1 # Kernel PPP
pseudo-device tun # Packet tunnel.
pseudo-device pty # Pseudo-ttys (telnet etc)
pseudo-device md # Memory "disks"
pseudo-device gif 4 # IPv6 and IPv4 tunneling
#pseudo-device faith 1 # IPv6-to-IPv4 relaying (translation)
# The `bpf' pseudo-device enables the Berkeley Packet Filter.
# Be aware of the administrative consequences of enabling this!
pseudo-device bpf #Berkeley packet filter
# the snoop device
pseudo-device snp 3 # snoop device
# USB support
#device uhci # UHCI PCI->USB interface
#device ohci # OHCI PCI->USB interface
#device usb # USB Bus (required)
#device ugen # Generic
#device uhid # "Human Interface Devices"
#device ukbd # Keyboard
#device ulpt # Printer
#device umass # Disks/Mass storage - Requires scbus and da
#device ums # Mouse
# USB Ethernet, requires mii
#device aue # ADMtek USB ethernet
#device cue # CATC USB ethernet
#device kue # Kawasaki LSI USB ethernet
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-hackers" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20020920105034.48316.qmail>