Date: Fri, 19 Nov 2004 12:20:20 +0100 From: Marcin <creep@desk.pl> To: freebsd-acpi@freebsd.org Subject: FBSD5.3 Compaq AP400 cannot warm-reboot (as in kern/27834) Message-ID: <20041119112020.GA12853@daedalus.desk.pl>
next in thread | raw e-mail | index | archive | help
Hello FreeBSD users! I have posted this problem to freebsd-questions, but then figured it was not actually the best place to send it. I'm experiencing the same problem described in http://www.freebsd.org/cgi/query-pr.cgi?pr=27834 but the fix included doesn't actually fix the problem. The system is FreeBSD 5.3 with GENERIC kernel on dual Compaq AP400 (Professional workstation) (dmesg/mptables below). When i reboot the system shutdowns properly (prints Rebooting...) but then just hangs with no activity (screen blank, disk diodes dead,etc). I have to push power button two times to reboot it, which is impossible with remote administration. This is the case with acpi.ko not loaded or with acpi.ko loaded but APIC disabled with hints.acpi.0.disabled. When i want to load acpi.ko wit APIC enabled i get a panic at system boottime with following message: "ACPI disabled by blacklist. Contact your BIOS vendor." (from sys/dev/acpica/acpi.c acpi_Startup returning AE_ERROR) called by: MADT: ACPI Startup failed with ACPI disabled by blacklist. Contact your BIOS vendor. Try disabling either ACPI or apic support. panic("Using MADT but ACPI doesn't work"); (from sys/i386/acpica/madt.c madt_setup_io()) (i'm writing these from memory, i didn't have serial console to catch the exact message. If it's needed, i'll provide the exact hand written version) I thought that there is nothing i could do except installing linux back [there was a linux system there before, the person using it said he had no problem with rebooting] but when the ACPI panic happes (the one listed above) and the user is prompted to press any key [or wait 15 secs] system prints Rebooting... and really restarts the machine the way i want! I searched for 'Rebooting' code in the kernel. found sys/kern/kern_shutdown.c shutdown_reset which calls cpu_reset(), then, checked what shutdown(1)/reboot(1) do and found they call the same function... so what happens in cpu_reset() what is different at panic and normal shutdown is still a mystery to me, but may be a hint for someone knowing the subject. Hints? Ideas? Pointers? -- Best regards, m. DMESG: [with apic disabled, unfortunately i can't catch messages on panic] Copyright (c) 1992-2004 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 5.3-RELEASE #0: Fri Nov 5 04:19:18 UTC 2004 root@harlow.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: Pentium II/Pentium II Xeon/Celeron (399.06-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x652 Stepping = 2 Features=0x183fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR> real memory = 335544320 (320 MB) avail memory = 318705664 (303 MB) ACPI disabled by blacklist. Contact your BIOS vendor. npx0: [FAST] npx0: <math processor> on motherboard npx0: INT 16 interface pcib0: <Intel 82443BX (440 BX) host to PCI bridge> pcibus 0 on motherboard pir0: <PCI Interrupt Routing Table: 8 Entries> on motherboard pci0: <PCI bus> on pcib0 $PIR: No matching entry for 0.11.INTA agp0: <Intel 82443BX (440 BX) host to PCI bridge> mem 0x54000000-0x57ffffff at device 0.0 on pci0 pcib1: <PCI-PCI bridge> at device 1.0 on pci0 pci1: <PCI bus> on pcib1 sym0: <875> port 0x5000-0x50ff mem 0x50a00000-0x50a00fff,0x50b00000-0x50b000ff irq 11 at device 11.0 on pci0 sym0: No NVRAM, ID 7, Fast-20, SE, parity checking sym0: [GIANT-LOCKED] fxp0: <Intel 82558 Pro/100 Ethernet> port 0x5400-0x541f mem 0x50800000-0x508fffff,0x50c00000-0x50c00fff irq 11 at device 12.0 on pci0 miibus0: <MII bus> on fxp0 inphy0: <i82555 10/100 media interface> on miibus0 inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto fxp0: Ethernet address: 00:08:c7:5c:cc:38 pci0: <display, VGA> at device 15.0 (no driver attached) isab0: <PCI-ISA bridge> at device 20.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <Intel PIIX4 UDMA33 controller> port 0x5440-0x544f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 20.1 on pci0 ata0: channel #0 on atapci0 ata1: channel #1 on atapci0 uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0x5420-0x543f irq 11 at device 20.2 on pci0 uhci0: [GIANT-LOCKED] usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0 usb0: USB revision 1.0 uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered pci0: <bridge, PCI-unknown> at device 20.3 (no driver attached) cpu0 on motherboard orm0: <ISA Option ROMs> at iomem 0xec000-0xeffff,0xc8000-0xcbfff,0xc0000-0xc7fff on isa0 pmtimer0 on isa0 atkbdc0: <Keyboard controller (i8042)> at port 0x64,0x60 on isa0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 kbd0 at atkbd0 atkbd0: [GIANT-LOCKED] fdc0: <Enhanced floppy controller> at port 0x3f0-0x3f5 irq 6 drq 2 on isa0 fdc0: [FAST] fd0: <1440-KB 3.5" drive> on fdc0 drive 0 ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0 ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode ppc0: FIFO with 16/16/8 bytes threshold ppbus0: <Parallel port bus> on ppc0 plip0: <PLIP network interface> on ppbus0 lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port ppi0: <Parallel I/O> on ppbus0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 16550A sio1 at port 0x2f8-0x2ff irq 3 on isa0 sio1: type 16550A vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 unknown: <PNP0401> can't assign resources (port) unknown: <PNP0501> can't assign resources (port) unknown: <PNP0501> can't assign resources (port) unknown: <PNP0700> can't assign resources (port) unknown: <PNP0303> can't assign resources (port) unknown: <PNP0c02> can't assign resources (port) unknown: <PNP0c02> can't assign resources (port) Timecounter "TSC" frequency 399062929 Hz quality 800 Timecounters tick every 10.000 msec acd0: CDROM <COMPAQ CR-588/LC15> at ata0-master PIO4 Waiting 15 seconds for SCSI devices to settle da0 at sym0 bus 0 target 0 lun 0 da0: <HP 4.26GB B 68-5541 5541> Fixed Direct Access SCSI-2 device da0: 40.000MB/s transfers (20.000MHz, offset 16, 16bit), Tagged Queueing Enabled da0: 4067MB (8330543 512 byte sectors: 255H 63S/T 518C) Mounting root from ufs:/dev/da0s1a MPTables [with blank lines truncated] =============================================================================== MPTable, version 2.0.15 ------------------------------------------------------------------------------- MP Floating Pointer Structure: location: BIOS physical address: 0x000f6420 signature: '_MP_' length: 16 bytes version: 1.4 checksum: 0xfd mode: Virtual Wire ------------------------------------------------------------------------------- MP Config Table Header: physical address: 0x000f6430 signature: 'PCMP' base table length: 396 version: 1.4 checksum: 0x75 OEM ID: 'COMPAQ ' Product ID: 'Workstation ' OEM table pointer: 0x00000000 OEM table size: 0 entry count: 40 local APIC address: 0xfee00000 extended table length: 0 extended table checksum: 0 ------------------------------------------------------------------------------- MP Config Base Table Entries: -- Processors: APIC ID Version State Family Model Step Flags 1 0x10 BSP, usable 6 5 2 0x183fbff 0 0x10 AP, usable 6 5 2 0x183fbff -- Bus: Bus ID Type 0 PCI 1 PCI 9 ISA -- I/O APICs: APIC ID Version State Address 8 0x11 usable 0xfec00000 -- I/O Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN# INT active-lo level 0 12:A 8 20 INT active-lo level 0 11:A 8 21 INT active-lo level 0 1:A 8 22 INT active-lo level 0 1:B 8 23 INT active-lo level 0 16:A 8 16 INT active-lo level 0 16:B 8 17 INT active-lo level 0 16:C 8 18 INT active-lo level 0 16:D 8 19 INT active-lo level 0 15:A 8 18 INT active-lo level 0 15:B 8 19 INT active-lo level 0 15:C 8 16 INT active-lo level 0 15:D 8 17 INT active-lo level 0 14:A 8 19 INT active-lo level 0 14:B 8 16 INT active-lo level 0 14:C 8 17 INT active-lo level 0 14:D 8 18 INT active-lo level 0 13:A 8 17 INT active-lo level 0 13:B 8 18 INT active-lo level 0 13:C 8 19 INT active-lo level 0 13:D 8 16 INT conforms conforms 9 0 8 2 INT conforms conforms 9 1 8 1 INT conforms conforms 9 3 8 3 INT conforms conforms 9 4 8 4 INT conforms conforms 9 5 8 5 INT conforms conforms 9 6 8 6 INT conforms conforms 9 7 8 7 INT conforms conforms 9 8 8 8 INT conforms conforms 9 9 8 9 INT conforms conforms 9 10 8 10 INT conforms conforms 9 12 8 12 INT conforms conforms 9 13 8 13 INT conforms conforms 9 14 8 14 INT conforms conforms 9 15 8 15 ===============================================================================
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20041119112020.GA12853>