Date: Wed, 23 Nov 2005 18:40:31 +0100 (CET) From: kama <kama@pvp.se> To: Hendry Sarumpaet <list-freebsd-stable@ezekiel.jasatel.net.id> Cc: freebsd-stable@freebsd.org Subject: Re: 6.0 Stable reboots randomly during high load. Message-ID: <20051123183903.F59053@ns1.as.pvp.se> In-Reply-To: <155534764.20051123223521@ezekiel.jasatel.net.id> References: <20051123134710.G57888@ns1.as.pvp.se> <155534764.20051123223521@ezekiel.jasatel.net.id>
next in thread | previous in thread | raw e-mail | index | archive | help
Try adding a lot of disk IO too. I believe that the problem lays within that area. I get a load of aprox 6 on that machine. /Bjorn On Wed, 23 Nov 2005, Hendry Sarumpaet wrote: > Hello kama, > > Wednesday, November 23, 2005, 8:04:36 PM, you wrote: > > > I have a HP DL380G3 Dual 2.4 w HT disabled. > > > This server is running as a newsserver (Diablo) and recieving more or less > > a full feed. aprox 200Mbps in and out. When the load rises the system > > reboots. > > > I can occupy it with high CPU load w/o problem, but once I allow > > connections to the machine, it will operate for a couple of hours and then > > reboot. It gets aprox 100 connections to the machine, all of them either > > write or read from disk. > > Just for the sharing, We've HP Proliant DL380 G4 with Dual 3.4 Ghz > HTT enabled 2 MB RAM. > this hardware act as our production router it seems > pretty robust on our lab enviroment with netperf we can succesfully forwarded packet up to > 600Mbps(symetric) through bge(configured with 10 vlan) connected to > catalyst Trunk port. CPU load around 60 % under the circumtances > above. currently it run as router with Full internet BGP feed (160K > prefix) with 3 neighbor upstream and moderate IPFW rule as > lightweight packet filter and bandwidth shapper. > nothing special on the configuration it runs with polling and IP > fastforwarding turn on with USB disabled via BIOS and ACPI turn off. > It runs on RELENG_6 latelly as of Nov 11 2005. > > attached boot message and kernel configuration. > > > > > > > > The kernel is GENERIC with small changes. (look at diff below) > > > This system had a working 5.4 system installed before, that did not suffer > > from these reboots. > > > How do I proceed for further gathering of information before I downgrade > > it to 5.4 again? > > > /Bjorn > > > - snip - > > > Copyright (c) 1992-2005 The FreeBSD Project. > > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > > The Regents of the University of California. All rights reserved. > > FreeBSD 6.0-STABLE #8: Mon Nov 21 14:45:30 CET 2005 > > root@newspeer3:/usr/obj/usr/src/sys/newspeer > > ACPI APIC Table: <COMPAQ 00000083> > > Timecounter "i8254" frequency 1193182 Hz quality 0 > > CPU: Intel(R) Xeon(TM) CPU 2.40GHz (2387.52-MHz 686-class CPU) > > Origin = "GenuineIntel" Id = 0xf29 Stepping = 9 > > > Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> > > Features2=0x4400<CNTX-ID,<b14>> > > Hyperthreading: 2 logical CPUs > > real memory = 4110393344 (3919 MB) > > avail memory = 4022607872 (3836 MB) > > FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs > > cpu0 (BSP): APIC ID: 0 > > cpu1 (AP): APIC ID: 6 > > MADT: Forcing active-low polarity and level trigger for SCI > > ioapic0 <Version 1.1> irqs 0-15 on motherboard > > ioapic1 <Version 1.1> irqs 16-31 on motherboard > > ioapic2 <Version 1.1> irqs 32-47 on motherboard > > ioapic3 <Version 1.1> irqs 48-63 on motherboard > > npx0: [FAST] > > npx0: <math processor> on motherboard > > npx0: INT 16 interface > > acpi0: <COMPAQ P29> on motherboard > > acpi0: Power Button (fixed) > > pci_link0: <ACPI PCI Link IUSB> on acpi0 > > pci_link1: <ACPI PCI Link IN16> on acpi0 > > pci_link2: <ACPI PCI Link IN17> on acpi0 > > pci_link3: <ACPI PCI Link IN18> on acpi0 > > pci_link4: <ACPI PCI Link IN19> on acpi0 > > pci_link5: <ACPI PCI Link IN20> on acpi0 > > pci_link6: <ACPI PCI Link IN21> on acpi0 > > pci_link7: <ACPI PCI Link IN22> on acpi0 > > pci_link8: <ACPI PCI Link IN23> on acpi0 > > pci_link9: <ACPI PCI Link IN24> on acpi0 > > pci_link10: <ACPI PCI Link IN25> on acpi0 > > pci_link11: <ACPI PCI Link IN26> on acpi0 > > pci_link12: <ACPI PCI Link IN27> on acpi0 > > pci_link13: <ACPI PCI Link IN28> on acpi0 > > pci_link14: <ACPI PCI Link IN29> on acpi0 > > pci_link15: <ACPI PCI Link IN30> on acpi0 > > pci_link16: <ACPI PCI Link IN31> on acpi0 > > pci_link17: <ACPI PCI Link IN32> on acpi0 > > pci_link18: <ACPI PCI Link IN33> on acpi0 > > pci_link19: <ACPI PCI Link IN34> on acpi0 > > Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000 > > acpi_timer0: <32-bit timer at 3.579545MHz> port 0x920-0x923 on acpi0 > > cpu0: <ACPI CPU> on acpi0 > > cpu1: <ACPI CPU> on acpi0 > > pcib0: <ACPI Host-PCI bridge> on acpi0 > > pci0: <ACPI PCI bus> on pcib0 > > pci0: <display, VGA> at device 3.0 (no driver attached) > > pci0: <base peripheral> at device 4.0 (no driver attached) > > pci0: <base peripheral> at device 4.2 (no driver attached) > > isab0: <PCI-ISA bridge> at device 15.0 on pci0 > > isa0: <ISA bus> on isab0 > > atapci0: <ServerWorks CSB5 UDMA100 controller> port > > 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x2000-0x200f at device 15.1 on pci0 > > ata0: <ATA channel 0> on atapci0 > > ata1: <ATA channel 1> on atapci0 > > ohci0: <OHCI (generic) USB controller> mem 0xf5ef0000-0xf5ef0fff irq 7 at > > device 15.2 on pci0 > > ohci0: [GIANT-LOCKED] > > usb0: OHCI version 1.0, legacy support > > usb0: SMM does not respond, resetting > > usb0: <OHCI (generic) USB controller> on ohci0 > > usb0: USB revision 1.0 > > uhub0: (0x1166) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > > uhub0: 4 ports with 4 removable, self powered > > pcib1: <ACPI Host-PCI bridge> on acpi0 > > pci1: <ACPI PCI bus> on pcib1 > > ciss0: <Compaq Smart Array 5i> port 0x3000-0x30ff mem > > 0xf7cc0000-0xf7cfffff,0xf7bf0000-0xf7bf3fff irq 30 at device 3.0 on pci1 > > ciss0: [GIANT-LOCKED] > > pcib2: <ACPI Host-PCI bridge> on acpi0 > > pci2: <ACPI PCI bus> on pcib2 > > bge0: <Broadcom BCM5703 Gigabit Ethernet, ASIC rev. 0x1002> mem > > 0xf7df0000-0xf7dfffff irq 29 at device 1.0 on pci2 > > miibus0: <MII bus> on bge0 > > brgphy0: <BCM5703 10/100/1000baseTX PHY> on miibus0 > > brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, > > 1000baseTX-FDX, auto > > bge0: Ethernet address: 00:0b:cd:f3:af:4d > > bge1: <Broadcom BCM5703 Gigabit Ethernet, ASIC rev. 0x1002> mem > > 0xf7de0000-0xf7deffff irq 31 at device 2.0 on pci2 > > miibus1: <MII bus> on bge1 > > brgphy1: <BCM5703 10/100/1000baseTX PHY> on miibus1 > > brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, > > 1000baseTX-FDX, auto > > bge1: Ethernet address: 00:0b:cd:f3:af:4c > > pcib3: <ACPI Host-PCI bridge> on acpi0 > > pci3: <ACPI PCI bus> on pcib3 > > pcib4: <PCI-PCI bridge> at device 1.0 on pci3 > > pci4: <PCI bus> on pcib4 > > ciss1: <HP Smart Array 6400> port 0x4000-0x40ff mem 0xf7ef0000-0xf7ef1fff > > irq 20 at device 4.0 on pci4 > > ciss1: [GIANT-LOCKED] > > ciss2: <HP Smart Array 6400 EM> port 0x4400-0x44ff mem > > 0xf7e70000-0xf7e71fff irq 21 at device 5.0 on pci4 > > ciss2: [GIANT-LOCKED] > > pcib5: <ACPI Host-PCI bridge> on acpi0 > > pci6: <ACPI PCI bus> on pcib5 > > pci6: <base peripheral, PCI hot-plug controller> at device 30.0 (no driver > > attached) > > acpi_tz0: <Thermal Zone> on acpi0 > > atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0 > > atkbd0: <AT Keyboard> irq 1 on atkbdc0 > > kbd0 at atkbd0 > > atkbd0: [GIANT-LOCKED] > > sio0: <Standard PC COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 > > sio0: type 16550A > > fdc0: <floppy drive controller (FDE)> port 0x3f2-0x3f5 irq 6 drq 2 on > > acpi0 > > fdc0: [FAST] > > fd0: <1440-KB 3.5" drive> on fdc0 drive 0 > > pmtimer0 on isa0 > > orm0: <ISA Option ROMs> at iomem > > 0xc0000-0xc7fff,0xc8000-0xcbfff,0xcc000-0xcffff,0xd0000-0xd17ff,0xee000-0xeffff > > on isa0 > > ppc0: parallel port not found. > > sc0: <System console> at flags 0x100 on isa0 > > sc0: VGA <16 virtual consoles, flags=0x300> > > sio1: configured irq 3 not in bitmap of probed irqs 0 > > sio1: port may not be enabled > > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 > > Timecounters tick every 1.000 msec > > acd0: CDROM <COMPAQ CD-ROM SN-124/N104> at ata0-master PIO4 > > da0 at ciss0 bus 0 target 0 lun 0 > > da0: <COMPAQ RAID 1 VOLUME OK> Fixed Direct Access SCSI-0 device > > da0: 135.168MB/s transfers > > da0: 17359MB (35553120 512 byte sectors: 255H 32S/T 4357C) > > da1 at ciss0 bus 0 target 1 lun 0 > > da1: <COMPAQ RAID 1 VOLUME OK> Fixed Direct Access SCSI-0 device > > da1: 135.168MB/s transfers > > da1: 17359MB (35553120 512 byte sectors: 255H 32S/T 4357C) > > da2 at ciss1 bus 0 target 0 lun 0 > > da2: <COMPAQ RAID 1 VOLUME OK> Fixed Direct Access SCSI-0 device > > da2: 135.168MB/s transfers > > da2: 138919MB (284506560 512 byte sectors: 255H 32S/T 34866C) > > SMP: AP CPU #1 Launched! > > Trying to mount root from ufs:/dev/da0s1a > > WARNING: / was not properly dismounted > > WARNING: /usr was not properly dismounted > > WARNING: /var was not properly dismounted > > bge0: link state changed to UP > > bge1: link state changed to UP > > > # diff -ub GENERIC newspeer > > --- GENERIC Fri Oct 28 21:21:27 2005 > > +++ newspeer Mon Nov 21 14:02:53 2005 > > @@ -19,10 +19,10 @@ > > # $FreeBSD: src/sys/i386/conf/GENERIC,v 1.429.2.4 2005/10/28 19:21:27 jhb > > Exp $ > > > machine i386 > > -cpu I486_CPU > > -cpu I586_CPU > > +#cpu I486_CPU > > +#cpu I586_CPU > > cpu I686_CPU > > -ident GENERIC > > +ident newspeer > > > # To statically compile in device wiring instead of /boot/device.hints > > #hints "GENERIC.hints" # Default places to look for > > devices. > > @@ -33,7 +33,7 @@ > > options SCHED_4BSD # 4BSD scheduler > > options PREEMPTION # Enable kernel thread preemption > > options INET # InterNETworking > > -options INET6 # IPv6 communications protocols > > +#options INET6 # IPv6 communications protocols > > options FFS # Berkeley Fast Filesystem > > options SOFTUPDATES # Enable FFS soft updates support > > options UFS_ACL # Support for access control lists > > @@ -62,6 +62,11 @@ > > options AHD_REG_PRETTY_PRINT # Print register bitfields in > > debug > > # output. Adds ~215k to driver. > > options ADAPTIVE_GIANT # Giant mutex is adaptive. > > + > > +options DEVICE_POLLING > > + > > +# To make an SMP kernel, the next line is needed > > +options SMP # Symmetric MultiProcessor Kernel > > > device apic # I/O APIC > > > _______________________________________________ > > freebsd-stable@freebsd.org mailing list > > http://lists.freebsd.org/mailman/listinfo/freebsd-stable > > To unsubscribe, send any mail to > > "freebsd-stable-unsubscribe@freebsd.org" > > >
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20051123183903.F59053>