Date: Fri, 13 Oct 2006 19:32:39 -0500 From: Mark Kane <mark@mkproductions.org> To: freebsd-stable <freebsd-stable@freebsd.org> Subject: Machine hangs when loading snd_emu10k1 Message-ID: <20061013193239.211edf9a@localhost>
next in thread | raw e-mail | index | archive | help
[-- Attachment #1 --]
Hi everyone.
I rebooted my machine today and when it came back up and I tried to
load the snd_emu10k1 kernel module, the machine hung without returning
to the prompt. I tried waiting 5-10+ minutes and it was totally
irrecoverable. At that point, nothing had changed since the last
reboot so it was weird that it would happen all of a sudden.
Last week I did cvsup to RELENG_6 after 6.2 BETA 2 was out and built
world/kernel with the intent to update and use it, but I never got
around to finishing the process (I had not installed anything either,
so it was just sitting all built). So tonight when the hanging of
emu10k1 happened, I did the installkernel/installworld process as
normal thinking something might have been fixed between my previous
cvsup (September 21 I believe) and my current one from Oct 5.
Unfortunately there was no change in behavior -- it hung again and I
waited at least 10 minutes before hard rebooting.
I'm currently running:
FreeBSD amd64.localhost 6.2-PRERELEASE FreeBSD 6.2-PRERELEASE #15: Thu
Oct 5 17:52:05 CDT 2006
mixx941@amd64.localhost:/usr/obj/usr/src/sys/AMD643000 amd64
With a Sound Blaster Augidy 2 Platinum:
none2@pci2:8:0: class=0x040100 card=0x10021102 chip=0x00041102 rev=0x04
hdr=0x00 vendor = 'Creative Labs'
device = 'SoundBlaster Audigy Audigy Audio Processor'
class = multimedia
subclass = audio
none3@pci2:8:1: class=0x098000 card=0x00601102 chip=0x70031102 rev=0x04
hdr=0x00 vendor = 'Creative Labs'
device = 'EMU10K2 Audigy Gameport'
class = input device
fwohci0@pci2:8:2: class=0x0c0010 card=0x00101102 chip=0x40011102
rev=0x04 hdr=0x00 vendor = 'Creative Labs'
device = 'EMU10K2 Audigy IEEE1394 Firewire Controller'
class = serial bus
subclass = FireWire
Later on tonight I can try to cvsup to RELENG_6 and rebuild again to see
if it has been fixed already, but I need my CPU power for some encoding
at the moment. Also, I'd rather not have to do a third hard reboot with
an hour long fsck for seven hard drives, so I wanted to post here first
in case it's known already or if anyone has any suggestions before
doing it again.
Thanks in advance.
-Mark
--
Internet Radio:
Party107 (Trance/Electronic) - http://www.party107.com
Rock 101.9 The Edge (Rock) - http://www.rock1019.net
IRC:
MIXXnet IRC Network - irc.mixxnet.net (Nick: MIXX941)
[-- Attachment #2 --]
Copyright (c) 1992-2006 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 6.2-PRERELEASE #15: Thu Oct 5 17:52:05 CDT 2006
mixx941@amd64.localhost:/usr/obj/usr/src/sys/AMD643000
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: AMD Athlon(tm) 64 Processor 3000+ (2009.79-MHz K8-class CPU)
Origin = "AuthenticAMD" Id = 0xfc0 Stepping = 0
Features=0x78bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2>
AMD Features=0xe0500800<SYSCALL,NX,MMX+,LM,3DNow+,3DNow>
real memory = 1610547200 (1535 MB)
avail memory = 1543823360 (1472 MB)
ACPI APIC Table: <Nvidia AWRDACPI>
ioapic0 <Version 1.1> irqs 0-23 on motherboard
acpi0: <Nvidia AWRDACPI> on motherboard
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
cpu0: <ACPI CPU> on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff,0xcf0-0xcf3 on acpi0
pci0: <ACPI PCI bus> on pcib0
agp0: <NVIDIA nForce3-250 AGP Controller> mem 0xf0000000-0xf7ffffff at device 0.0 on pci0
isab0: <PCI-ISA bridge> at device 1.0 on pci0
isa0: <ISA bus> on isab0
pci0: <serial bus, SMBus> at device 1.1 (no driver attached)
ohci0: <OHCI (generic) USB controller> mem 0xfc002000-0xfc002fff irq 20 at device 2.0 on pci0
ohci0: [GIANT-LOCKED]
usb0: OHCI version 1.0, legacy support
usb0: <OHCI (generic) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: nVidia OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 4 ports with 4 removable, self powered
ohci1: <OHCI (generic) USB controller> mem 0xfc003000-0xfc003fff irq 21 at device 2.1 on pci0
ohci1: [GIANT-LOCKED]
usb1: OHCI version 1.0, legacy support
usb1: <OHCI (generic) USB controller> on ohci1
usb1: USB revision 1.0
uhub1: nVidia OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 4 ports with 4 removable, self powered
ehci0: <NVIDIA nForce3 250 USB 2.0 controller> mem 0xfc004000-0xfc0040ff irq 22 at device 2.2 on pci0
ehci0: [GIANT-LOCKED]
usb2: EHCI version 1.0
usb2: companion controllers, 4 ports each: usb0 usb1
usb2: <NVIDIA nForce3 250 USB 2.0 controller> on ehci0
usb2: USB revision 2.0
uhub2: nVidia EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub2: 8 ports with 8 removable, self powered
atapci0: <nVidia nForce3 Pro UDMA133 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xf000-0xf00f at device 8.0 on pci0
ata0: <ATA channel 0> on atapci0
ata1: <ATA channel 1> on atapci0
atapci1: <nVidia nForce3 Pro SATA150 controller> port 0x9f0-0x9f7,0xbf0-0xbf3,0x970-0x977,0xb70-0xb73,0xe400-0xe40f,0xe800-0xe87f irq 20 at device 10.0 on pci0
ata2: <ATA channel 0> on atapci1
ata3: <ATA channel 1> on atapci1
pcib1: <ACPI PCI-PCI bridge> at device 11.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pci1: <display, VGA> at device 0.0 (no driver attached)
pcib2: <ACPI PCI-PCI bridge> at device 14.0 on pci0
pci2: <ACPI PCI bus> on pcib2
atapci2: <Promise PDC20269 UDMA133 controller> port 0x8000-0x8007,0x8400-0x8403,0x8800-0x8807,0x8c00-0x8c03,0x9000-0x900f mem 0xfb000000-0xfb003fff irq 18 at device 6.0 on pci2
ata4: <ATA channel 0> on atapci2
ata5: <ATA channel 1> on atapci2
pci2: <multimedia, audio> at device 8.0 (no driver attached)
pci2: <input device> at device 8.1 (no driver attached)
fwohci0: <1394 Open Host Controller Interface> mem 0xfb010000-0xfb0107ff,0xfb004000-0xfb007fff irq 17 at device 8.2 on pci2
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:02:3c:00:91:01:6c:20
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:02:3c:01:6c:20
fwe0: Ethernet address: 02:02:3c:01:6c:20
fwe0: if_start running deferred for Giant
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwohci0: Initiate bus reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
ahc0: <Adaptec 2940 Ultra2 SCSI adapter> port 0x9c00-0x9cff mem 0xfb012000-0xfb012fff irq 17 at device 9.0 on pci2
ahc0: [GIANT-LOCKED]
aic7890/91: Ultra2 Wide Channel A, SCSI Id=7, 32/253 SCBs
skc0: <Marvell Gigabit Ethernet> port 0xa000-0xa0ff mem 0xfb008000-0xfb00bfff irq 19 at device 11.0 on pci2
skc0: Marvell Yukon Lite Gigabit Ethernet rev. A3(0x7)
sk0: <Marvell Semiconductor, Inc. Yukon> on skc0
sk0: Ethernet address: 00:0f:ea:4f:83:8b
miibus0: <MII bus> on sk0
e1000phy0: <Marvell 88E1000 Gigabit PHY> on miibus0
e1000phy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX-FDX, auto
atapci3: <ITE IT8212F UDMA133 controller> port 0xa410-0xa417,0xa800-0xa803,0xac10-0xac17,0xb000-0xb003,0xb400-0xb40f irq 16 at device 12.0 on pci2
ata6: <ATA channel 0> on atapci3
ata7: <ATA channel 1> on atapci3
fwohci1: <Texas Instruments TSB43AB23> mem 0xfb011000-0xfb0117ff,0xfb00c000-0xfb00ffff irq 18 at device 14.0 on pci2
fwohci1: OHCI version 1.10 (ROM=1)
fwohci1: No. of Isochronous channels is 4.
fwohci1: EUI64 00:0f:ea:00:00:47:38:9b
fwohci1: Phy 1394a available S400, 3 ports.
fwohci1: Link S400, max_rec 2048 bytes.
firewire1: <IEEE1394(FireWire) bus> on fwohci1
fwe1: <Ethernet over FireWire> on firewire1
if_fwe1: Fake Ethernet address: 02:0f:ea:47:38:9b
fwe1: Ethernet address: 02:0f:ea:47:38:9b
fwe1: if_start running deferred for Giant
sbp1: <SBP-2/SCSI over FireWire> on firewire1
fwohci1: Initiate bus reset
fwohci1: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
firewire1: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire1: bus manager 0 (me)
fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0
fdc0: [FAST]
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
ppc0: <Standard parallel printer port> port 0x378-0x37f irq 7 on acpi0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
orm0: <ISA Option ROMs> at iomem 0xc0000-0xcf7ff,0xd2000-0xd47ff,0xd5000-0xd57ff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
ums0: Microsoft Microsoft 5-Button Mouse with IntelliEye(TM), rev 1.10/3.00, addr 2, iclass 3/1
ums0: 5 buttons and Z dir.
Timecounter "TSC" frequency 2009790491 Hz quality 800
Timecounters tick every 1.000 msec
ad0: 194481MB <Maxtor 6B200R0 BAH41BM0> at ata0-master UDMA133
acd0: DMA limited to UDMA33, device found non-ATA66 cable
acd0: DVDR <LITE-ON DVDRW SOHW-1693S/KS04> at ata1-slave UDMA33
ad6: 305245MB <Seagate ST3320620AS 3.AAC> at ata3-master SATA150
ad8: 76344MB <MAXTOR 6L080J4 A93.0500> at ata4-master UDMA133
ad10: 78166MB <Maxtor 6Y080P0 YAR41BW0> at ata5-master UDMA133
ad11: 156334MB <Maxtor 6Y160P0 YAR41BW0> at ata5-slave UDMA133
ad12: 194481MB <Maxtor 6B200P0 BAH41BM0> at ata6-master UDMA133
ad14: 239372MB <Maxtor 6Y250P0 YAR41BW0> at ata7-master UDMA133
Waiting 5 seconds for SCSI devices to settle
sa0 at ahc0 bus 0 target 4 lun 0
sa0: <SUN DLT4000 CC2E> Removable Sequential Access SCSI-2 device
sa0: 10.000MB/s transfers (10.000MHz, offset 15)
sa1 at ahc0 bus 0 target 6 lun 0
sa1: <ARCHIVE Python 06241-XXX 912L> Removable Sequential Access SCSI-3 device
sa1: 80.000MB/s transfers (40.000MHz, offset 32, 16bit)
cd0 at ata1 bus 0 target 1 lun 0
cd0: <LITE-ON DVDRW SOHW-1693S KS04> Removable CD-ROM SCSI-0 device
cd0: 33.000MB/s transfers
cd0: Attempt to query device size failed: NOT READY, Medium not present
ch0 at ahc0 bus 0 target 6 lun 1
ch0: <ARCHIVE Python 06241-XXX 912L> Removable Changer SCSI-3 device
ch0: 80.000MB/s transfers (40.000MHz, offset 32, 16bit)
ch0: 6 slots, 1 drive, 1 picker, 0 portals
Trying to mount root from ufs:/dev/ad0s1a
ipfw2 (+ipv6) initialized, divert loadable, rule-based forwarding disabled, default to deny, logging disabled
sk0: link state changed to UP
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20061013193239.211edf9a>