Date: Wed, 6 Jun 2007 09:16:48 +0200 From: Hans Petter Selasky <hselasky@c2i.net> To: freebsd-isdn@freebsd.org Subject: Re: Digium b410p with i4b Message-ID: <200706060916.48120.hselasky@c2i.net> In-Reply-To: <4665CAFA.3080801@wanagain.net> References: <4665CAFA.3080801@wanagain.net>
next in thread | previous in thread | raw e-mail | index | archive | help
On Tuesday 05 June 2007 22:43, Mikael Batard wrote:
> Hi,
>
> i'm trying to get the Digium b410p card (quadbri) working with i4b (svn
> trunk revision 510) on FreeBSD 6.2.
>
> I've added the vendor hardware code to the
> i4b/trunk/i4b/src/sys/i4b/layer1/ihfc2/i4b_hfc4s8s.h file :
> I4B_PCI_DRIVER(/* HFC-4S B410P */
> .vid =3D 0xb410d161,
> .sub =3D 0xb410d161);
Thanks for the ID, I've added it to the SVN repo. Maybe you want to do a "s=
vn=20
revert trunk/i4b/src/sys/i4b/layer1/ihfc2/i4b_hfc4s8s.h" then "svn update".
This entry should be under "double_clock" =3D 0.
>
> The card is detected with pciconf :
> $ pciconf -vl
> ihfc0@pci6:1:0: class=3D0x020400 card=3D0xb410d161 chip=3D0xb410d161 rev=
=3D0x01
> hdr=3D0x00
> class =3D network
> subclass =3D ISDN
>
> and isdnconfig :
> $ isdnconfig
> controller 8 =3D {
> Layer 1:
> description : HFC-4S PCI ISDN adapter
> type : passive ISDN (Basic Rate, 2xB)
> channels : 0x3
> serial : 0xabd5
> power_save : on
> dialtone : enabled
> attached : yes
> PH-state : F3: Deactivated
> Layer 2:
> driver_type : DRVR_DSS1_TE
> }
>
> If I insert the isdn cable in the card the PH-state change to this:
> PH-state : F7: Activated
>
> But if I call my isdn number (which is sent through the cable to the
> card), it doesn't work, i get no tone on my phone (which is external
> from this isdn network).
>
> I've tried to do some tests with capitest and isdndecode, and I've got
> lots of lines like this one :
=46irst you must ensure that you have set the correct protocol=20
using "isdnconfig". For example:
isdnconfig -u 8 -p DRVR_DSS1_TE
Then according to "man isdnconfig" it is also required to set "pcm_master"=
=20
mode before the card will operate. That is printed out in the "dmesg". This=
=20
is to avoid problems when you connect your HFC-4S to another clock source.
=46rom "man isdnconfig":
isdnconfig -m 0 pcm_64 \
-m 1 pcm_64 \
-u 8 pcm_64 pcm_map 0 1 end pcm_master te_mode \
-p DRVR_DSS1_TE \
-u 9 pcm_64 pcm_map 0 1 end pcm_master nt_mode \
power_on -p DRVR_DSS1_NT
>
> Asterisk 1.2.17, zaptel 1.4.1, libpri 1.4.0 and libpri-bristuff 1.2.3
> are installed.
> There are 2 other cards installed : 1 Digium TDM400p (with 2 FXO ports)
> and 1 Passive ISDN BRI card (which works perfectly except for echo
> cancellation).
You need to use "chan_capi" from the SVN repo, and not "zaptel", to get the=
=20
ISDN cards detected under Asterisk. Also I4B has a new Fast Fourier Transfo=
rm=20
Based Acoustic Echo Canceller. Did you try that?
Look at the "chan_capi/extensions.conf" and "chan_capi/capi.conf" example=20
files.
=2D-HPS
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?200706060916.48120.hselasky>