Date: Sun, 28 Sep 2008 11:21:19 +0200 From: "Julian Stacey" <jhs@berklix.org> To: stable@freebsd.org Cc: pyunyh@gmail.com, Jeremy Chadwick <koitsu@freebsd.org>, Abdullah Ibn Hamad Al-Marri <wearabnet@yahoo.ca> Subject: Re: rl0: watchdog timeout + 40, 000 ms ping with 7.1-BETA-i386-disc1.iso Message-ID: <200809280921.m8S9LJtA030248@fire.js.berklix.net> In-Reply-To: Your message "Fri, 26 Sep 2008 19:54:04 %2B0200." <200809261754.m8QHs41D011762@fire.js.berklix.net>
next in thread | previous in thread | raw e-mail | index | archive | help
Hi, Reference: > From: "Julian Stacey" <jhs@berklix.org> > Date: Fri, 26 Sep 2008 19:54:04 +0200 > Message-id: <200809261754.m8QHs41D011762@fire.js.berklix.net> "Julian Stacey" wrote: > Hi, > Reference: > > From: "Julian Stacey" <jhs@berklix.org> > > Date: Fri, 26 Sep 2008 19:16:57 +0200 > > Message-id: <200809261717.m8QHGvmx011312@fire.js.berklix.net> > > "Julian Stacey" wrote: > > > > I'm remaking binaries, > > > > New generic kernel built & installed, & install of all src/ done too. > > No improvement. > > > > > Is there reliable way to reproduce the issue? > > > > Its continuous, the machine virtually never does a ping in less > > than 10 seconds. > > > > > Anyway, would you try attached patch and let me know result? > > > > Thanks > > Done, doesnt help. > > Seeing a new message now too: > > ping: sendto: No buffer space available. > > > > Output of vmstat -i and pciconf -lv look the same as before > > > > It's a small card. Weighs 46 gram. I was going to write > > I could simply post it to you, & you could keep it if you > > want. As I had quessed it might be some new kind of card > > unexperienced before, > > RTL8139D, card just says made in China > > > > But I just grabbed another card > > card says Level One. > > chip 8139B > > & with both patched kernel & original no improvement. > > So I tried a totaly different card xl0 fails too, > > I think that 3com xl0 card was OK before in another box, > > so I'd guess not an rl problem, Sorry. > > > > Probably not 7.1 either, but probably a BIOS config problem of some sort. > > > > IRQ 12 was listed in Award BIOS as Primary, options were also secondary or disabled, so Ive set it disabled. > > PNP OS Yes > > Resources: Auto > > "Reset config data" to Enabled (I forgot before after card changes) > > > > Did another restore BIOS factory defaults, no help. > > Moved xl0 to another slot (all other 3 slots never use I guess, as > > chassis plates not torn off on what I guess is original chassis. > > No luck with xl0 > > I'm out of ideas. > > Got it working on xl > interrupt problem, I turned off lpt com2 & something else > in bios. > Got to go out now > Ill go back to rl0 too & report back soon > thanks for help both ! I'm wrong it is Not working. (I typed my own own card address of 192.168.x.x by mistake, not the 192.168.x.x of another host on net. ) Ive fiddled more with BIOS IRQ to no good effect (not suprsing, dont understand some options in BIOS & no MOtherboard manual for this Award BIOS 2A6LGB09, on box: fujitsu siemens t-bird I was wondering if setting anything to polling might help a bit I went looking with syctl -a -d | grep hw.pci hw.pci.do_power_nodriver: 0 hw.pci.do_power_nodriver: Place a function into D3 state when no driver attaches to it. 0 means hw.pci.do_power_resume: 1 hw.pci.do_power_resume: Transition from D3 -> D0 on resume. hw.pci.enable_io_modes: 1 hw.pci.enable_io_modes: Enable I/O and memory bits in the config register. Some BIOSes do not hw.pci.enable_msi: 1 hw.pci.enable_msi: Enable support for MSI interrupts hw.pci.enable_msix: 1 hw.pci.enable_msix: Enable support for MSI-X interrupts hw.pci.honor_msi_blacklist: 1 hw.pci.honor_msi_blacklist: Honor chipset blacklist for MSI hw.pci.host_mem_start: 2147483648 hw.pci.host_mem_start: Limit the host bridge memory to being above this address. Must be hw.pci.irq_override_mask: 57080 hw.pci.irq_override_mask: Mask of allowed irqs to try to route when it has no good clue about hw.pcic.intr_mask: 57016 hw.pcic.intr_mask: Mask of allowable interrupts for this laptop. The default is generally hw.pcic.pd6722_vsense: 1 hw.pcic.pd6722_vsense: Select CL-PD6722's VSENSE method. VSENSE is used to determine the Abdullah wrote: > Do you have poll enabled for rl0 ? I didnt understand question but after "man 4 polling" & eg ifconfig xl0 192.168.100.64 polling I dont see ifconfig -a showing polling Still stuck not working, with BSD showing: xl0 on irq10 BIOS showing irq10 disabled Changed bios irq10 to "Secondary" rebooted. PC Manufacturer has no manual on line (to describe BIOS options) Ideas & comments welcome ! Cheers, Julian -- Julian Stacey: BSDUnixLinux C Prog Admin SysEng Consult Munich www.berklix.com Mail plain ASCII text. HTML & Base64 text are spam. www.asciiribbon.org
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?200809280921.m8S9LJtA030248>