Date: Wed, 29 Oct 2008 15:02:04 +0100 From: Michael Moll <kvedulv@kvedulv.de> To: Marius Strobl <marius@alchemy.franken.de> Cc: freebsd-sparc64@freebsd.org Subject: Re: Booting of snapshot-iso on SUN Fire V280R Message-ID: <20081029140204.GS5156@darkthrone.kvedulv.de> In-Reply-To: <20081029081558.GB31338@alchemy.franken.de> References: <20081028172823.GO5156@darkthrone.kvedulv.de> <20081028221321.GA32214@alchemy.franken.de> <20081029001112.GR5156@darkthrone.kvedulv.de> <20081029081558.GB31338@alchemy.franken.de>
next in thread | previous in thread | raw e-mail | index | archive | help
Hi Marius, On Wed, Oct 29, 2008 at 09:15:58AM +0100, Marius Strobl wrote: > I'm uploading a new one at: > http://people.freebsd.org/~marius/8.0-20081028-SNAP-sparc64-disc1.iso.gz Besides one LOR everything seems fine now, thanks a lot! :) Sun Fire 280R (2 X UltraSPARC-III+) , No Keyboard Copyright 1998-2004 Sun Microsystems, Inc. All rights reserved. OpenBoot 4.16.4, 8192 MB memory installed, Serial #53054758. Ethernet address 0:3:ba:29:8d:26, Host ID: 83298d26. Rebooting with command: boot cdrom Boot device: /pci@8,700000/scsi@6/disk@6,0:f File and args: >> FreeBSD/sparc64 boot block Boot path: /pci@8,700000/scsi@6/disk@6,0:f Boot loader: /boot/loader Consoles: Open Firmware console Booting with sun4u support. Boot path set to /pci@8,700000/scsi@6/disk@6,0:a FreeBSD/sparc64 bootstrap loader, Revision 1.0 (root@nimrod.franken.de, Wed Oct 29 00:11:36 UTC 2008) bootpath="/pci@8,700000/scsi@6/disk@6,0:a" Loading /boot/defaults/loader.conf /boot/kernel/kernel data=0x813348+0x216928 syms=[0x8+0x91578+0x8+0x8387c] - Hit [Enter] to boot immediately, or any other key for command prompt. Booting [/boot/kernel/kernel]... jumping to kernel entry at 0xc0080000. GDB: no debug ports present KDB: debugger backends: ddb KDB: current backend: ddb Copyright (c) 1992-2008 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 8.0-20081028-SNAP #0: Wed Oct 29 02:22:05 UTC 2008 root@nimrod.franken.de:/usr/obj/usr/src/sys/GENERIC WARNING: WITNESS option enabled, expect reduced performance. real memory = 8589934592 (8192 MB) avail memory = 8381685760 (7993 MB) cpu0: Sun Microsystems UltraSparc-III+ Processor (900.00 MHz CPU) cpu1: Sun Microsystems UltraSparc-III+ Processor (900.00 MHz CPU) FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs registered firmware set <isp_1000> registered firmware set <isp_1040> registered firmware set <isp_1040_it> registered firmware set <isp_1080> registered firmware set <isp_1080_it> registered firmware set <isp_12160> registered firmware set <isp_12160_it> registered firmware set <isp_2100> registered firmware set <isp_2200> registered firmware set <isp_2300> registered firmware set <isp_2322> registered firmware set <isp_2400> kbd0 at kbdmux0 ath_hal: 0.10.5.10 (AR5210, AR5211, AR5212, AR5416, RF5111, RF5112, RF2413, RF5413, RF2133, RF2425, RF2417, REGOPS_FUNC) nexus0: <Open Firmware Nexus device> nexus0: <memory-controller> mem 0x40000400000-0x40000400047 type memory-controller (no driver attached) nexus0: <memory-controller> mem 0x40000c00000-0x40000c00047 type memory-controller (no driver attached) pcib0: <Sun Host-PCI bridge> mem 0x40004700000-0x40004717fff,0x40004410000-0x4000441004f,0x7ffee000000-0x7ffee0000ff irq 563,560,561,564,550 on nexus0 pcib0: Schizo, version 5, IGN 0x8, bus B, 33MHz pcib0: DVMA map: 0xc0000000 to 0xffffffff pcib0: [FILTER] pcib0: [FILTER] pcib0: [FILTER] pcib0: [FILTER] pci0: <OFW PCI bus> on pcib0 ebus0: <PCI-EBus3 bridge> mem 0x7d000000-0x7dffffff,0x7e000000-0x7e7fffff at device 5.0 on pci0 ebus0: <flashprom> addr 0-0x1fffff (no driver attached) ebus0: <i2c> addr 0x10000002e-0x10000002f,0x10000002d irq 35 (no driver attached) ebus0: <bbc> addr 0x100000000-0x1000fffff (no driver attached) ebus0: <power> addr 0x10030002e-0x10030002f,0x100300600-0x100300607 (no driver attached) ebus0: <i2c> addr 0x100000030-0x100000031 irq 35 (no driver attached) ebus0: <beep> addr 0x100000032-0x100000037 (no driver attached) rtc0: <Real-Time Clock> addr 0x100300070-0x100300071 irq 36 on ebus0 ebus0: <gpio> addr 0x100300600-0x100300607 (no driver attached) ebus0: <pmc> addr 0x100300700-0x100300701 (no driver attached) ebus0: <parallel> addr 0x100300278-0x100300287,0x10030002e-0x10030002f,0x100700000-0x10070000f irq 28 (no driver attached) uart0: <16550 or compatible> addr 0x1003062f8-0x1003062ff irq 46 on ebus0 uart0: [FILTER] uart1: <16550 or compatible> addr 0x1003083f8-0x1003083ff irq 45 on ebus0 uart1: [FILTER] uart1: console (115200,n,8,1) scc0: <Siemens SAB 82532 dual channel SCC> addr 0x100400000-0x10040007f irq 34 on ebus0 scc0: [FILTER] uart2: <SAB 82532 v3.2, channel A> on scc0 uart2: [FILTER] uart2: CTS oflow uart3: <SAB 82532 v3.2, channel B> on scc0 uart3: [FILTER] uart3: CTS oflow gem0: <Sun ERI 10/100 Ethernet> mem 0x100000-0x11ffff at device 5.1 on pci0 miibus0: <MII bus> on gem0 ukphy0: <Generic IEEE 802.3u media interface> PHY 1 on miibus0 ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto gem0: 2kB RX FIFO, 2kB TX FIFO gem0: Ethernet address: 00:03:ba:29:8d:26 gem0: [ITHREAD] ohci0: <Sun PCIO-2 USB controller> mem 0x1000000-0x1007fff at device 5.3 on pci0 ohci0: [GIANT-LOCKED] ohci0: [ITHREAD] usb0: OHCI version 1.0, legacy support usb0: <Sun PCIO-2 USB controller> on ohci0 usb0: USB revision 1.0 uhub0: <(0x108e) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0 uhub0: 4 ports with 4 removable, self powered sym0: <875> port 0x300-0x3ff mem 0x124000-0x1240ff,0x126000-0x126fff at device 6.0 on pci0 sym0: No NVRAM, ID 7, Fast-20, SE, parity checking sym0: [ITHREAD] sym1: <875> port 0x400-0x4ff mem 0x128000-0x1280ff,0x12a000-0x12afff at device 6.1 on pci0 sym1: No NVRAM, ID 7, Fast-20, SE, parity checking sym1: [ITHREAD] pcib1: <OFW PCI-PCI bridge> at device 3.0 on pci0 pci1: <OFW PCI bus> on pcib1 pci1: <bridge> at device 0.0 (no driver attached) hme0: <Sun HME 10/100 Ethernet> mem 0x3800000-0x3807fff at device 0.1 on pci1 miibus1: <MII bus> on hme0 ukphy1: <Generic IEEE 802.3u media interface> PHY 1 on miibus1 ukphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto hme0: Ethernet address: 00:03:ba:1f:72:39 hme0: [ITHREAD] pci1: <bridge> at device 1.0 (no driver attached) hme1: <Sun HME 10/100 Ethernet> mem 0x3808000-0x380ffff at device 1.1 on pci1 miibus2: <MII bus> on hme1 ukphy2: <Generic IEEE 802.3u media interface> PHY 1 on miibus2 ukphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto hme1: Ethernet address: 00:03:ba:1f:72:3a hme1: [ITHREAD] pci1: <bridge> at device 2.0 (no driver attached) hme2: <Sun HME 10/100 Ethernet> mem 0x3810000-0x3817fff at device 2.1 on pci1 miibus3: <MII bus> on hme2 ukphy3: <Generic IEEE 802.3u media interface> PHY 1 on miibus3 ukphy3: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto hme2: Ethernet address: 00:03:ba:1f:72:3b hme2: [ITHREAD] pci1: <bridge> at device 3.0 (no driver attached) hme3: <Sun HME 10/100 Ethernet> mem 0x3818000-0x381ffff at device 3.1 on pci1 miibus4: <MII bus> on hme3 ukphy4: <Generic IEEE 802.3u media interface> PHY 1 on miibus4 ukphy4: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto hme3: Ethernet address: 00:03:ba:1f:72:3c hme3: [ITHREAD] pcib2: <Sun Host-PCI bridge> mem 0x40004600000-0x40004617fff,0x40004410000-0x4000441004f,0x7ffec000000-0x7ffec0000ff irq 562,560,561,564 on nexus0 pcib2: Schizo, version 5, IGN 0x8, bus A, 66MHz Timecounter "pcib2" frequency 150000000 Hz quality 100 pcib2: DVMA map: 0xc0000000 to 0xffffffff pcib2: [FILTER] pci2: <OFW PCI bus> on pcib2 isp0: <Qlogic ISP 2200 PCI FC-AL Adapter> port 0x300-0x3ff mem 0x100000-0x100fff at device 4.0 on pci2 isp0: [ITHREAD] isp0: Board Type 2200, Chip Revision 0x5, loaded F/W Revision 2.2.6 isp0: invalid NVRAM header isp0: invalid NVRAM header nexus0: <syscons> type unknown (no driver attached) Timecounter "tick" frequency 900000000 Hz quality 10 Timecounters tick every 1.000 msec Waiting 5 seconds for SCSI devices to settle md0: Preloaded image </boot/mfsroot> 4194304 bytes at 0xc0b3ea78 da0 at isp0 bus 0 target 0 lun 0 da0: <SEAGATE ST373405FSUN72G 0438> Fixed Direct Access SCSI-3 device da0: 100.000MB/s transfers da0: Command Queueing Enabled da0: 70007MB (143374738 512 byte sectors: 255H 63S/T 8924C) da1 at isp0 bus 0 target 1 lun 0 da1: <SEAGATE ST373405FSUN72G 0438> Fixed Direct Access SCSI-3 device da1: 100.000MB/s transfers WWNN 0x20000004cfa12ee6 WWPN 0x21000004cfa12ee6 PortID 0xe8 da1: Command Queueing Enabled da1: 70007MB (143374738 512 byte sectors: 255H 63S/T 8924C) SMP: AP CPU #1 Launched! WARNING: WITNESS option enabled, expect reduced performance. cd0 at sym0 bus 0 target 6 lun 0 cd0: <TOSHIBA DVD-ROM SD-M1401 1009> Removable CD-ROM SCSI-2 device cd0: 3.300MB/s transfers cd0: cd present [979800 x 512 byte records] GEOM_LABEL: Label for provider cd0 is iso9660/FreeBSD_Install. Trying to mount root from ufs:/dev/md0 lock order reversal: 1st 0xfffff8000309e070 user map (user map) @ /usr/src/sys/vm/vm_map.c:3115 2nd 0xfffff800035c94e0 ufs (ufs) @ /usr/src/sys/kern/vfs_subr.c:2046 KDB: stack backtrace: _witness_debugger() at _witness_debugger+0x38 witness_checkorder() at witness_checkorder+0xcf8 __lockmgr_args() at __lockmgr_args+0x2d0 ffs_lock() at ffs_lock+0x88 VOP_LOCK1_APV() at VOP_LOCK1_APV+0x110 _vn_lock() at _vn_lock+0x80 vget() at vget+0x120 vnode_pager_lock() at vnode_pager_lock+0x240 vm_fault() at vm_fault+0x208 trap_pfault() at trap_pfault+0x198 trap() at trap+0xd0 -- fast data access mmu miss tar=0x476001 %o7=0xc0081208 -- userland() at 0x10015c user trace: trap %o7=0xc0081208 pc 0x10015c, sp 0x7fdffffe531 pc 0, sp 0x7fdffffe5f1 done /stand/sysinstall running as init on serial console Kind Regards -- Michael Moll e-mail : kvedulv@kvedulv.de WWW : http://www.kvedulv.de/ GSM : +49 175 606 7861
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20081029140204.GS5156>