Date: Wed, 27 Oct 2010 12:54:53 +0000 From: Alexander Best <arundel@freebsd.org> To: Garrett Cooper <gcooper@FreeBSD.org> Cc: Bruce Cran <bruce@cran.org.uk>, Tijl Coosemans <tijl@coosemans.org>, Oliver Fromme <olli@lurza.secnetix.de>, freebsd-hackers@freebsd.org, mav@freebsd.org, Dag-Erling =?iso-8859-15?Q?Sm=F8rgrav?= <des@des.no> Subject: Re: Summary: Re: Spin down HDD after disk sync or before power off Message-ID: <20101027125453.GA8433@freebsd.org> In-Reply-To: <AANLkTi=hvkXvAkv68jjpJSKSKZ5a-0yn=Vje4ZjSPc=F@mail.gmail.com> References: <201009161742.24228.tijl@coosemans.org> <201009161619.o8GGJAmv035378@lurza.secnetix.de> <20101018155944.GA12425@freebsd.org> <868w1r92rf.fsf@ds4.des.no> <20101021122110.GA65490@freebsd.org> <86zku77mj6.fsf@ds4.des.no> <20101021135442.000054c9@unknown> <20101021134114.GB72290@freebsd.org> <20101027124113.GA6206@freebsd.org> <AANLkTi=hvkXvAkv68jjpJSKSKZ5a-0yn=Vje4ZjSPc=F@mail.gmail.com>
next in thread | previous in thread | raw e-mail | index | archive | help
On Wed Oct 27 10, Garrett Cooper wrote:
> On Wed, Oct 27, 2010 at 5:41 AM, Alexander Best <arundel@freebsd.org> wrote:
> > On Thu Oct 21 10, Alexander Best wrote:
> >> On Thu Oct 21 10, Bruce Cran wrote:
> >> > On Thu, 21 Oct 2010 14:33:49 +0200
> >> > Dag-Erling Smørgrav <des@des.no> wrote:
> >> >
> >> > > The problem with setting a short idle timeout is that, on a typical
> >> > > laptop or desktop system, you end up spinning the disk down and back
> >> > > up several hundred times a day, which increases power consumption, I/O
> >> > > latency and wear.
> >> >
> >> > Do we think our users are silly enough to set a short timeout of just a
> >> > few minutes? I'd think most would use a setting of 20-30 minutes at
> >> > a minimum. I never did understand why there were so many warnings;
> >> > after all, some laptops even come with a default APM scheme in their
> >> > HDDs that powers the disk down after 7 seconds!
> >>
> >> personally i still think something like the attached patch would be nice to
> >> have. there's a chance users might type the following:
> >>
> >> 'atacontrol spindown device 10'
> >>
> >> thinking the timeout value is measured in minutes. although this gets mentioned
> >> in atacontrol(4) it might still be worth reminding the user that he/she is
> >> performing actions which could damage the hardware.
> >
> > i just stumbled upon PR 144770, where a somebody seems to have mistaken the
> > spindown value for minutes instead of seconds. so i really think we should have
> > this warning in atacontrol!
> >
> > +1 from brucec, if i understood him correctly.
> >
> > another possibility would be of course changing the spindown value from seconds
> > to minutes. imo this seems very reasonable, because measuring spindown time in
> > seconds is too fine grained and not intuitive. just like specifying the
> > 'shutdown -p XX' delay in microseconds would not be useful. ;)
> >
> > cheers.
> > alex
> >
> >>
> >> cheers.
> >> alex
> >>
> >> >
> >> > --
> >> > Bruce Cran
> >>
> >> --
> >> a13x
> >
> >> diff --git a/sbin/atacontrol/atacontrol.c b/sbin/atacontrol/atacontrol.c
> >> index 4354ddf..75a131a 100644
> >> --- a/sbin/atacontrol/atacontrol.c
> >> +++ b/sbin/atacontrol/atacontrol.c
> >> @@ -317,6 +317,10 @@ ata_spindown(int fd, const char *dev, const char *arg)
> >>
> >> if (arg != NULL) {
> >> tmo = strtoul(arg, NULL, 0);
> >> + if (tmo < 600)
> >> + warnx("setting spindown timeout below 10 minutes is \
> >> + not recommended (see EXAMPLES section of \
> >> + atacontrol(8))\n");
> >> if (ioctl(fd, IOCATASSPINDOWN, &tmo) < 0)
> >> err(1, "ioctl(IOCATASSPINDOWN)");
> >> } else {
>
> Why not just be consistent with other interfaces and provide
> suffixes for the values to parse out integral times (i.e. 1 [second],
> 1m, 2h)? As long as the value is behavior is properly documented in
> the manpage (and potentially as examples in the usage message), that
> should be enough.
that would increase usability, since users don't have to specify large values
in seconds, if they e.g. want the spindown to happen after 24 hours (24*60*60).
but this will not solve the real issue: specifying 'atacontrol spindown 1s'
WILL damage your hardware! imo users should be reminded about this even if this
is already mentioned in the manual.
also: will current scripts which set 'atacontrol spindown 600' e.g. continue to
work after implementing the use of suffixes?
> Thanks,
> -Garrett
--
a13x
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20101027125453.GA8433>